scholarly journals On the Efficiency of a Piezoelectric Energy Harvester under Combined Aeroelastic and Base Excitation

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 962
Author(s):  
Antiopi-Malvina Stamatellou ◽  
Anestis I. Kalfas
Keyword(s):  
Conversion Efficiency ◽  
Power Output ◽  
Polyvinylidene Fluoride ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Elastic Strain Energy ◽  
Rate Of Change ◽  
Mode Shapes ◽  
Base Excitation ◽  
Piezoelectric Energy

A flutter-type, nonlinear piezoelectric energy harvester was tested in various combinations of aerodynamic and harmonic base excitation to study its power output and efficiency. The commercial polyvinylidene fluoride film transducer LDT1-028K was used in 33 excitation mode. The aerodynamic excitation was created by a centrifugal fan and the base excitation by a cone speaker. The excitations were produced by varying independently the mean airflow velocity and the frequency of base vibration. A capacitive load was used to store the harvested energy. A line laser was employed along with long exposure photography and high-speed video, for the visualization of the piezo film’s mode shapes and the measurement of maximum tip deflection. The harvested power was mapped along with the maximum tip deflection of the piezo-film, and a process of optimally combining the two excitation sources for maximum power harvesting is demonstrated. The energy conversion efficiency is defined by means of electrical power output divided by the elastic strain energy rate of change during oscillations. The efficiency was mapped and correlated with resonance conditions and results from other studies. It was observed that the conversion efficiency is related to the phase difference between excitation and response and tends to decrease as the excitation frequency rises.

Modeling and Experimental Validations of a Piezoelectric Energy Harvester Under Combined Galloping and Base Excitations

2014 ◽  
Author(s):  
Amin Bibo ◽  
Abdessattar Abdelkefi ◽  
Mohammed F. Daqaq
Keyword(s):  
Bluff Body ◽  
Energy Harvester ◽  
Constitutive Relations ◽  
Excitation Frequency ◽  
Primary Resonance ◽  
Beam Theory ◽  
Excitation Amplitude ◽  
The Body ◽  
Base Excitation ◽  
Piezoelectric Energy

This paper develops an experimentally validated model of a piezoelectric energy harvester under combined aeroelastic-galloping and base excitations. To that end, an energy harvester consisting of a thin piezoelectric cantilever beam subjected to vibratory base excitation is considered. To permit galloping excitation, a bluff body is rigidly attached at the free end such that a net aerodynamic lift is generated as the incoming airflow separates on both sides of the body giving rise to limit cycle oscillations when the flow velocity exceeds a critical value. A nonlinear electromechanical distributed-parameter model of the harvester under the combined excitation is derived using the energy approach and by adopting the nonlinear Euler-Bernoulli beam theory, linear constitutive relations for the piezoelectric transduction, and the quasi-steady assumption for the aerodynamic loading. The partial differential equations of the system are discretized and a reduced-order-model is obtained. The mathematical model is validated by conducting a series of experiments with different loading conditions represented by wind speed, base excitation amplitude, and excitation frequency around the primary resonance.

Design and Experimental Verification of Torsion-Bending Low-Frequency Piezoelectric Energy Harvesters

2016 ◽  
Author(s):  
Hichem Abdelmoula ◽  
Nathan Sharpes ◽  
Hyeon Lee ◽  
Abdessattar Abdelkefi ◽  
Shashank Priya
Keyword(s):  
System Analysis ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Low Frequency ◽  
Load Resistance ◽  
Mode Shapes ◽  
Low Frequencies ◽  
Piezoelectric Energy ◽  
The Masses ◽  
Tip Mass

We design and experimentally validate a zigzag piezoelectric energy harvester that can generate energy at low frequencies and which can be used to operate low-power consumption electronic devices. The harvester is composed of metal and piezoelectric layers and is used to harvest energy through direct excitations. A computational model is developed using Abaqus to determine the exact mode shapes and coupled frequencies of the considered energy harvester in order to design a broadband torsion-bending mechanical system. Analysis is then performed to determine the optimal load resistance. The computational results are compared and validated with the experimental measurements. More detailed analysis is then carried out to investigate the effects of the masses on the bending and torsion natural frequencies of the harvester and generated power levels. The results show that due to the coupling between the bending and torsion modes of the zigzag structure, highest levels of the harvested power are obtained when the excitation frequency matches the coupled frequency of torsion type for three different values of the tip mass.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

scholarly journals Analysis of a Cantilevered Piezoelectric Energy Harvester in Different Orientations for Rotational Motion

Sensors ◽  
2020 ◽  
Vol 20 (4) ◽  
pp. 1206 ◽  
Author(s):  
Wei-Jiun Su ◽  
Jia-Han Lin ◽  
Wei-Chang Li
Keyword(s):  
Theoretical Model ◽  
Resonant Frequency ◽  
Rotational Motion ◽  
Axial Load ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Experimental Studies ◽  
Piezoelectric Energy ◽  
Piezoelectric Cantilever ◽  
Tip Mass

This paper investigates a piezoelectric energy harvester that consists of a piezoelectric cantilever and a tip mass for horizontal rotational motion. Rotational motion results in centrifugal force, which causes the axial load on the beam and alters the resonant frequency of the system. The piezoelectric energy harvester is installed on a rotational hub in three orientations—inward, outward, and tilted configurations—to examine their influence on the performance of the harvester. The theoretical model of the piezoelectric energy harvester is developed to explain the dynamics of the system and experiments are conducted to validate the model. Theoretical and experimental studies are presented with various tilt angles and distances between the harvester and the rotating center. The results show that the installation distance and the tilt angle can be used to adjust the resonant frequency of the system to match the excitation frequency.

Optimization of energy harvesting based on the uniform deformation of piezoelectric ceramic

2016 ◽  
Vol 09 (05) ◽  
pp. 1650069 ◽  
Author(s):  
Yaoze Liu ◽  
Tongqing Yang ◽  
Fangming Shu
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Piezoelectric Ceramic ◽  
Energy Harvester ◽  
Optimization Method ◽  
Piezoelectric Energy ◽  
Bonding Area ◽  
Almost All ◽  
Matching Load ◽  
Tip Mass

Since the piezoelectric properties were used for energy harvesting, almost all forms of energy harvester needs to be bonded with a mass block to achieve pre-stress. In this article, disc type piezoelectric energy harvester is chosen as the research object and the relationship between mass bonding area and power output is studied. It is found that if the bonding area is changed as curved, which is usually complanate in previous studies, the deformation of the circular piezoelectric ceramic is more uniform and the power output is enhanced. In order to test the change of the deformation, we spray several homocentric annular electrodes on the surface of a piece of bare piezoelectric ceramic and the output of each electrode is tested. Through this optimization method, the power output is enhanced to more than 11[Formula: see text]mW for a matching load about 24[Formula: see text]k[Formula: see text] and a tip mass of 30[Formula: see text]g at its resonant frequency of 139[Formula: see text]Hz.

Performance Analysis of Piezoelectric Energy Harvesting in Pavement: Laboratory Testing and Field Simulation

2019 ◽  
Vol 2673 (3) ◽  
pp. 115-124 ◽  
Author(s):  
Abbas F. Jasim ◽  
Hao Wang ◽  
Greg Yesner ◽  
Ahmad Safari ◽  
Pat Szary
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Laboratory Testing ◽  
Energy Harvester ◽  
Total Power ◽  
Piezoelectric Energy Harvesting ◽  
Loading Frequency ◽  
Vehicle Speed ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

This study investigated the energy harvesting performance of a piezoelectric module in asphalt pavements through laboratory testing and multi-physics based simulation. The energy harvester module was assembled with layers of Bridge transducers and tested in the laboratory. A decoupled approach was used to study the interaction between the energy harvester and the surrounding pavement. The effects of embedment location, vehicle speed, and temperature on energy harvesting performance were investigated. The analysis findings indicate that the embedment location and vehicle speed affects the resulted power output of the piezoelectric energy harvesting system. The embedment depth of the energy module affects both the magnitude and frequency of stress pulse on top of the energy module induced by tire loading. On the other hand, higher vehicle speed causes greater loading frequency and thus greater power output; the effect of pavement temperature is negligible. The analysis of total power output before reaching fatigue failure of the energy module can be used to determine the optimum embedment location in the asphalt layer. The proposed energy harvesting system provides great potential to generate green energy from waste kinetic energy in roadway pavements. Field study is recommended to verify these findings with long-term performance monitoring of pavement with embedded energy harvesters.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

scholarly journals An Exact Analytical Solution to Exponentially Tapered Piezoelectric Energy Harvester

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
H. Salmani ◽  
G. H. Rahimi ◽  
S. A. Hosseini Kordkheili
Keyword(s):  
Analytical Solution ◽  
Energy Harvester ◽  
Exact Analytical Solution ◽  
Mode Shapes ◽  
Electric Resistance ◽  
Coupled Equations ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam ◽  
Parallel Connections ◽  
Tip Mass

It has been proven that tapering the piezoelectric beam through its length optimizes the power extracted from vibration based energy harvesting. This phenomenon has been investigated by some researchers using semianalytical, finite element and experimental methods. In this paper, an exact analytical solution is presented to calculate the power generated from vibration of exponentially tapered unimorph and bimorph with series and parallel connections. The mass normalized mode shapes of the exponentially tapered piezoelectric beam with tip mass are implemented to transfer the proposed electromechanical coupled equations into modal coordinates. The steady states harmonic solution results are verified both numerically and experimentally. Results show that there exist values for tapering parameter and electric resistance in a way that the output power per mass of the energy harvester will be maximized. Moreover it is concluded that the electric resistance must be higher than a specified value for gaining more power by tapering the beam.

scholarly journals Wearable Core-Shell Piezoelectric Nanofiber Yarns for Body Movement Energy Harvesting

Nanomaterials ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 555 ◽  
Author(s):  
Sang Hyun Ji ◽  
Yong-Soo Cho ◽  
Ji Sun Yun
Keyword(s):  
Polyvinylidene Fluoride ◽  
Output Voltage ◽  
Energy Harvester ◽  
Body Movement ◽  
Effective Area ◽  
Core Shell ◽  
Body Movements ◽  
Bending Tests ◽  
The Core ◽  
Piezoelectric Energy

In an effort to fabricate a wearable piezoelectric energy harvester based on core-shell piezoelectric yarns with external electrodes, flexible piezoelectric nanofibers of BNT-ST (0.78Bi0.5Na0.5TiO3-0.22SrTiO3) and polyvinylidene fluoride-trifluoroethylene (PVDF-TrFE) were initially electrospun. Subsequently, core-shell piezoelectric nanofiber yarns were prepared by twining the yarns around a conductive thread. To create the outer electrode layers, the core-shell piezoelectric nanofiber yarns were braided with conductive thread. Core-shell piezoelectric nanofiber yarns with external electrodes were then directly stitched onto the fabric. In bending tests, the output voltages were investigated according to the total length, effective area, and stitching interval of the piezoelectric yarns. Stitching patterns of the piezoelectric yarns on the fabric were optimized based on these results. The output voltages of the stitched piezoelectric yarns on the fabric were improved with an increase in the pressure, and the output voltage characteristics were investigated according to various body movements of bending and pressing conditions.

Sign in / Sign up

Export Citation Format

Share Document