scholarly journals Analysis of Shape Memory Behavior and Mechanical Properties of Shape Memory Polymer Composites Using Thermal Conductive Fillers

Micromachines ◽  
2021 ◽  
Vol 12 (9) ◽  
pp. 1107
Author(s):  
Mijeong Kim ◽  
Seongeun Jang ◽  
Sungwoong Choi ◽  
Junghoon Yang ◽  
Jungpil Kim ◽  
...  
Keyword(s):  
Physical Properties ◽  
Shape Memory ◽  
Polymer Composites ◽  
Shape Recovery ◽  
Memory Performance ◽  
Shape Memory Polymer ◽  
Scanning Calorimetry ◽  
Wide Range ◽  
Nanocarbon Materials ◽  
Shape Memory Composite

Shape memory polymers (SMPs) are attracting attention for their use in wearable displays and biomedical materials due to their good biocompatibility and excellent moldability. SMPs also have the advantage of being lightweight with excellent shape recovery due to their low density. However, they have not yet been applied to a wide range of engineering fields because of their inferior physical properties as compared to those of shape memory alloys (SMAs). In this study, we attempt to find optimized shape memory polymer composites. We also investigate the shape memory performance and physical properties according to the filler type and amount of hardener. The shape memory composite was manufactured by adding nanocarbon materials of graphite and non-carbon additives of Cu. The shape-recovery mechanism was compared, according to the type and content of the filler. The shape fixation and recovery properties were analyzed, and the physical properties of the shape recovery composite were obtained through mechanical strength, thermal conductivity and differential scanning calorimetry analysis.

scholarly journals Bio-Based Epoxy Shape-Memory Thermosets from Triglycidyl Phloroglucinol

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 542 ◽  
Author(s):  
David Santiago ◽  
Dailyn Guzmán ◽  
Francesc Ferrando ◽  
Àngels Serra ◽  
Silvia De la Flor
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Memory Performance ◽  
Crosslinking Agent ◽  
Shape Memory Polymers ◽  
Crosslinking Density ◽  
Mechanical Analysis ◽  
Diglycidyl Ether ◽  
Partial Substitution ◽  
Scanning Calorimetry

A series of bio-based epoxy shape-memory thermosetting polymers were synthesized starting from a triglycidyl phloroglucinol (3EPOPh) and trimethylolpropane triglycidyl ether (TPTE) as epoxy monomers and a polyetheramine (JEF) as crosslinking agent. The evolution of the curing process was studied by differential scanning calorimetry (DSC) and the materials obtained were characterized by means of DSC, thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), stress-strain tests, and microindentation. Shape-memory properties were evaluated under free and totally constrained conditions. All results were compared with an industrial epoxy thermoset prepared from standard diglycidyl ether of Bisphenol A (DGEBA). Results revealed that materials prepared from 3EPOPh were more reactive and showed a tighter network with higher crosslinking density and glass transition temperatures than the prepared from DGEBA. The partial substitution of 3EPOPh by TPTE as epoxy comonomer caused an increase in the molecular mobility of the materials but without worsening the thermal stability. The shape-memory polymers (SMPs) prepared from 3EPOPh showed good mechanical properties as well as an excellent shape-memory performance. They showed almost complete shape-recovery and shape-fixation, fast shape-recovery rates, and recovery stress up to 7 MPa. The results obtained in this study allow us to conclude that the triglycidyl phloroglucinol derivative of eugenol is a safe and environmentally friendly alternative to DGEBA for preparing thermosetting shape-memory polymers.

RECENT PROGRESSES IN POLYMERIC SMART MATERIALS

2010 ◽  
Vol 24 (15n16) ◽  
pp. 2351-2356 ◽  
Author(s):  
YAN-JU LIU ◽  
XIN LAN ◽  
HAI-BAO LU ◽  
JIN-SONG LENG
Keyword(s):  
Shape Memory ◽  
Smart Materials ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Strain Energy Function ◽  
Electroactive Polymer ◽  
Electrically Conductive ◽  
Wide Range ◽  
Polymer Actuator ◽  
Analysis Of Stability

Smart materials can be defined as materials that sense and react to environmental conditions or stimuli. In recent years, a wide range of novel smart materials have been developed in biomaterials, sensors, actuators, etc. Their applications cover aerospace, automobile, telecommunications, etc. This paper presents some recent progresses in polymeric smart materials. Special emphasis is laid upon electroactive polymer (EAP), shape memory polymer (SMP) and their composites. For the electroactive polymer, an analysis of stability of dielectric elastomer using strain energy function is derived, and one type of electroactive polymer actuator is presented. For the shape memory polymer, a new method is developed to use infrared laser to actuate the SMP through the optical fiber embedded within the SMP. Electrically conductive nanocarbon powders are utilized as the fillers to improve the electrical conductivity of polymer. A series of fundamental investigations of electroactive SMP are performed and the shape recovery is demonstrated.

scholarly journals Development of Trans-1,4-Polyisoprene Shape-Memory Polymer Composites Reinforced with Carbon Nanotubes Modified by Polydopamine

Polymers ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 110
Author(s):  
Chuang Zhang ◽  
Long Li ◽  
Yuanhang Xin ◽  
Jiaqi You ◽  
Jing Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Shape Memory ◽  
Polymer Composites ◽  
Photoelectron Spectroscopy ◽  
Memory Performance ◽  
Shape Memory Polymer ◽  
Structure And Properties ◽  
X Ray

In this study, which was inspired by mussel-biomimetic bonding research, carbon nanotubes (CNTs) were interfacially modified with polydopamine (PDA) to prepare a novel nano-filler (CNTs@PDA). The structure and properties of the CNTs@PDA were studied using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA). The CNTs and the CNTs@PDA were used as nanofillers and melt-blended into trans-1,4 polyisoprene (TPI) to create shape-memory polymer composites. The thermal stability, mechanical properties, and shape-memory properties of the TPI/CNTs and TPI/CNTs@PDA composites were systematically studied. The results demonstrate that these modifications enhanced the interfacial interaction, thermal stability, and mechanical properties of TPI/CNTs@PDA composites while maintaining shape-memory performance.

Influence of Radialization Dosage on Shape Memory Effect of Polystyrene Copolymer

2008 ◽  
Vol 47-50 ◽  
pp. 690-693 ◽  
Author(s):  
Da Wei Zhang ◽  
Jin Song Leng ◽  
Yan Ju Liu
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Smart Materials ◽  
Shape Recovery ◽  
Memory Performance ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Mechanical Analysis ◽  
Styrene Copolymer

This paper is concerned about the synthesis of shape memory styrene copolymer and the investigation of the influence of radialization dosage on its shape memory effect. As one of novel actuators in smart materials, shape memory polymers (SMPs) have been investigated intensively. Styrene copolymer with proper cross-linking degree can exhibit shape memory effect (SME). In this paper, the influence of radialization on shape memory effect of styrene copolymer was investigated through altering the dosage of radialization. The radialization dosage of styrene copolymer was determined by changed radicalization time. The glass transition temperature (Tg) of styrene copolymerwas measured by Dynamic Mechanical Analysis (DMA). The shape memory performance of styrene copolymer with different radiated dosage was also evaluated. Results indicated that the shape memory polymer (SMP) was synthesized successfully. The Tg increased from 60°C to 65°C followed by increasing the radialization dosage. Moreover, the SMP experienced good SME and the largest reversible strain of the SMP reached as high as 150%. When heating above Tg+30°C (different copolymers performed different Tg), the shape recovery speed of the copolymers increased with increasing the radialization dosage. However, the recovery speed decreased with increasing the radialization dosage at the same temperature of 95°C.

An investigation on electro-induced shape memory performances of CE/EP/CB/SCF composites applied for deployable structure

2020 ◽  
Vol 40 (3) ◽  
pp. 203-210 ◽  
Author(s):  
Tianning Ren ◽  
Guangming Zhu ◽  
Yi Liu ◽  
Xiao Hou
Keyword(s):  
Carbon Black ◽  
Shape Memory ◽  
Memory Performance ◽  
Shape Memory Polymer ◽  
Content Increase ◽  
Deployable Structure ◽  
Shape Memory Properties ◽  
Shape Memory Composites ◽  
Shape Memory Composite ◽  
Short Carbon

AbstractThe objective of this work is to investigate the thermomechanical, electrical, and shape-memory properties of bisphenol A-type cyanate ester (BACE)/polybutadiene epoxy (PBEP)/carbon black (CB) composite and assess its feasibility applied for deployable structure. Using a BACE/PBEP polymer as matrix and superconducting carbon black (CB) and short carbon fibers (SCFs) as reinforcing material, the shape memory composite was prepared by compression molding. The effects of CB and SCF content on the shape memory properties of the composites were investigated. The results demonstrate that the glass transition temperature (Tg) and the storage modulus of the composites increases as SCFs content increase. Because of the synergic effect of CB and SCFs, the shape memory composites exhibit excellent shape memory performance, and the shape recovery ratio is about 100%. With the increase in SCF content, the recovery time decreased, and the volume electrical resistivity of the composite could decrease by adding a small amount of SCFs. According to the above results, a shape memory polymer composite deployable structure was prepared.

An experimental–numerical study on shape memory behavior of PU/PCL/ZnO ternary blend

2018 ◽  
Vol 30 (1) ◽  
pp. 116-126 ◽  
Author(s):  
M Abbasi-Shirsavar ◽  
M Baghani ◽  
M Taghavimehr ◽  
M Golzar ◽  
M Nikzad ◽  
...  
Keyword(s):  
Shape Memory ◽  
Polymer Composites ◽  
Zno Nanoparticles ◽  
Shape Recovery ◽  
Numerical Study ◽  
Soft Segment ◽  
Shape Memory Polymer ◽  
Ternary Blend ◽  
Recovery Ratio ◽  
Shape Memory Behavior

Shape memory polymer composites have attracted significant attention due to novel properties and great applications. In this article, we focus on the fabrication and simulation of polyurethane/polycaprolactone nanocomposites. The polyurethane/polycaprolactone blends containing ZnO nanoparticles (5 to 30 wt%) are fabricated using a solution mixing and casting method. It is found that significant improvement of polyurethane/polycaprolactone composites in Young’s modulus is achieved by incorporating 20 wt% of ZnO nanoparticles; also, the results of the shape recovery ratio reveal that adding an optimum amount of ZnO (the reinforcement) can increase the shape recovery ratio (for 20 wt% of ZnO). These results could most likely be explained by the fact that some particles restrict the hard segment–soft segment interactions and provide more mobility to polycaprolactone components, while the other nanoparticles can act as the nucleating agent for polycaprolactone chains. A generalized Maxwell model is then used to examine the shape memory behavior of shape memory polymer composites. The dynamic mechanical thermal analysis results are utilized to define the model coefficients and the simulation is carried out to determine the shape recovery ratio. Simulation of this shape recovery ratio for shape memory polymer composites reveals that the numerical results are in good agreement with those of the experimental data.

Modeling the Thermoviscoelastic Properties and Recovery Behavior of Shape Memory Polymer Composites

2013 ◽  
Vol 81 (4) ◽  
Author(s):  
Stephen Alexander ◽  
Rui Xiao ◽  
Thao D. Nguyen
Keyword(s):  
Stress Response ◽  
Shape Memory ◽  
Polymer Composites ◽  
Young’S Modulus ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Strain Recovery ◽  
Recovery Stress ◽  
Recovery Behavior ◽  
Recovery Response

This work investigated the effects of stiff inclusions on the thermoviscoelastic properties and recovery behavior of shape memory polymer composites. Recent manufacturing advances have increased the applicability and interest in SMPCs made with carbon and glass inclusions. The resulting biphasic material introduces changes to both the thermal and mechanical responses, which are not fully understood. Previous studies of these effects have been concerned chiefly with experimental characterization and application of these materials. The few existing computational studies have been constrained by the limitations of available constitutive models for the SMP matrix material. The present study applied previously developed finite-deformation, time-dependent thermoviscoelastic models for amorphous SMPs to investigate the properties and shape memory behavior of SMPCs with a hexagonal arrangement of hard inclusions. A finite element model of a repeating unit cell was developed for the periodic microstructure of the SMPC and used to evaluate the temperature-dependent viscoelastic properties, including the storage modulus, tan δ, coefficient of thermal expansion, and Young's modulus, as well as the shape recovery response, characterized by the unconstrained strain recovery response and the constrained recovery stress response. The presence of inclusions in greater volume fractions were shown to lower both the glass transition and recovery temperatures slightly, while substantially increasing the storage and Young's modulus. The inclusions also negligibly affected the unconstrained strain recovery rate, while decreasing the constrained recovery stress response. The results demonstrate the potential of using hard fillers to increase the stiffness and hardness of amorphous networks for structural application without significantly affecting the temperature-dependence and time-dependence of the shape recovery response.

A Comparative Analysis of Orientation on the Shape Memory Effect of Fabric Reinforced Shape Memory Polymer Composites

2015 ◽  
Vol 830-831 ◽  
pp. 529-532 ◽  
Author(s):  
D. Mohanakrishnan ◽  
M. Sureshkumar
Keyword(s):  
Comparative Analysis ◽  
Shape Memory ◽  
Polymer Composites ◽  
Smart Materials ◽  
Memory Performance ◽  
Shape Memory Polymer ◽  
Matrix Material ◽  
Resin Matrix ◽  
Structural Applications ◽  
Stimulus Temperature

Shape memory polymer composites (SMPC) are a new kind of smart materials where many researches have been carried out. In SMPC, shape memory polymers serves as a matrix material and particles or fibers act as reinforcements. As structural applications demand structures to withstand load and stiffness, particles reinforced SMPC does not serve for it. Therefore fiber/fabric reinforced SMPC used widely for such applications. SMPC’S changes its shape during a typical thermo-mechanical cycle and retracts to its original shape upon external stimulus (temperature). Molecular mechanism is the driving force of these SMP’s. SMP consists of 1.molecular switches and 2. netpoints. This project deals with Epoxy shape memory resin (Matrix material) and fabrics such as Glass, Kevlar and Carbon (Reinforcements).A Comparative analysis was carried out to find which combination gives the best results by bend test. Different orientations were tried for bidirectional fabrics such as (0/90)3, (0/45)3, ((0/90)/(±45)/(0/90)) specimens. Finally it was concluded that Carbon fabric which has the orientation of (0/90/±45/0/90) gives better shape memory performance.

scholarly journals Study on carbon nanotube/shape memory polymer composites and their applications in wireless worm actuator

2021 ◽  
Vol 37 ◽  
pp. 636-650
Author(s):  
Wei-Hsuan Hsu ◽  
Chia-Wei Lin ◽  
Yi-Hung Chen ◽  
Shang-Ru Wu ◽  
Hung-Yin Tsai
Keyword(s):  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Carbon Nanotube ◽  
Reaction Time ◽  
Shape Memory ◽  
Polymer Composites ◽  
Microwave Heating ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Experimental Results

Abstract In this study, the surface of the carbon nanotubes was modified by chemical functionalization. The carbon nanotubes were placed in a mixed acid solution with a nitric acid-to-sulfuric acid volume ratio of 1:3. The results of the functionalization of the carbon nanotubes were investigated by controlling the reaction time. From the experimental results, the functionalized carbon nanotubes with a reaction time of 12 hours show good dispersibility. In the study of the essential characteristics of composite materials, it was observed that the tensile strength decreased with increase of carbon nanotube content. Compared with the result of the tensile strength test, it can be found that with increasing carbon nanotube content, the microwave heating and shape recovery speed are greatly improved. The experimental results show that the shape memory polymer composite with 4 wt% carbon nanotubes has the fastest microwave heating rate, so it takes only 2 minutes to achieve complete shape recovery. Finally, this study used shape memory polymer composites doped with 4 wt% carbon nanotubes as the driving end, combined with an elastic structure made of polyimide (PI) film using origami techniques to form a worm actuator. In the test, the system could move a distance of 6 mm forward during a microwave time of 1 minute. In addition, this research also constructed a physical model of shape memory polymer and explored the simple movement mechanism of the system.

Sign in / Sign up

Export Citation Format

Share Document