scholarly journals Photocatalytic Degradation of Selected Pharmaceuticals Using g-C3N4 and TiO2 Nanomaterials

Nanomaterials ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 1194 ◽  
Author(s):  
Smýkalová ◽  
Sokolová ◽  
Foniok ◽  
Matějka ◽  
Praus
Keyword(s):  
Photocatalytic Degradation ◽  
High Performance ◽  
Diffuse Reflectance Spectroscopy ◽  
Attenuated Total Reflection ◽  
Aqueous Environment ◽  
X Ray Diffraction ◽  
Mass Detection ◽  
Fourier Transformed Infrared Spectroscopy ◽  
Transmission Electron ◽  
Tio2 Nanomaterials

Exfoliated graphitic carbon nitride (g-C3N4) and two commercially available nanomaterials from titanium dioxide (P25 and CG300) were tested for the photocatalytic degradation of paracetamol (PAR), ibuprofen (IBU), and diclofenac (DIC). Prior to photocatalytic experiments, the nanomaterials were characterized by common methods, such as X-ray diffraction (XRD), UV–VIS diffuse reflectance spectroscopy (DRS), Fourier transformed infrared spectroscopy in attenuated total reflection mode (FTIR–ATR), transmission electron microscopy (TEM), physisorption of nitrogen, and dynamic vapor adsorption (DVS) of water. The sizes and specific surface area (SSA) of the TiO2 nanoparticles were 6 nm and 300 m2·g−1 for CG300 and 21 nm and 50 m2·g−1 for P25. The SSA of g-C3N4 was 140 m2·g−1. All photocatalytic experiments were performed under UV (368 nm), as well as VIS (446 nm) irradiation. TiO2 P25 was the most active photocatalyst under UV irradiation and g-C3N4 was the most active one under VIS irradiation. Photodegradation yields were evaluated by means of high performance liquid chromatography (HPLC) and reaction intermediates were identified using gas chromatography with mass detection (GC–MS). Paracetamol and ibuprofen were totally removed but the intermediates of diclofenac were observed even after 6 h of irradiation. Some intermediates, such as carbazole-1-acetic acid, 2,6-dichloraniline, and hydroxylated derivates of diclofenac were identified. This study showed that g-C3N4 is a promising photocatalyst for the degradation of pharmaceuticals in an aqueous environment, under visible light.

Controllable one-step synthesis of ZnO nanostructures using molybdophosphoric acid

2014 ◽  
Vol 68 (4) ◽  
Author(s):  
Hamed Rashidi ◽  
Ali Ahmadpour ◽  
Fatemeh Bamoharram ◽  
Seyed Zebarjad ◽  
Majid Heravi ◽  
...  
Keyword(s):  
Photocatalytic Degradation ◽  
High Performance ◽  
Hydrothermal Reaction ◽  
Hexagonal Phase ◽  
Zno Nanostructures ◽  
Molybdophosphoric Acid ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
Transmission Electron ◽  
One Step

AbstractZnO nanostructures were synthesised in a hydrothermal reaction of zinc acetate in the presence of molybdophosphoric acid (H3[PMo12O40]) as well as its vanadium-substituted acid (H4[PMo11VO40]) at various times, temperatures, and concentrations. The ZnO nanostructures were characterised by X-ray diffraction, transmission electron microscopy, and Fourier transform infrared spectroscopy. The results demonstrated that the synthesised products are crystalline with a zincite hexagonal phase. Various ZnO nanostructures, such as nanoparticles, microrods, and nanosheets, were produced by changing the experimental conditions. The photocatalytic degradation of methyl orange was also investigated using the ZnO nanoparticles thus prepared. These particles exhibited high performance in the photocatalytic degradation of MO and almost 100 % decolourisation occurred within only 20 min.

scholarly journals Enhancement of Photocatalytic Activity of ZnO/SiO2by Nanosized Pt for Photocatalytic Degradation of Phenol in Wastewater

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
R. M. Mohamed ◽  
M. A. Barakat
Keyword(s):  
Photocatalytic Activity ◽  
Photocatalytic Degradation ◽  
Surface Area ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Phenol Degradation ◽  
Synthetic Wastewater ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

ZnO- nanoparticles were synthesized by a sol-gel technique from and tetraethyl orthosilicate (TEOS). The synthesized samples were further modified by nanosized Pt from H2PtCl6solution through photoassisted deposition (PAD) and impregnation (Img) routes. The obtained samples were characterized by a series of techniques including X-ray diffraction (XRD), UV-Vis diffuse reflectance spectroscopy, N2adsorption, extended X-ray absorption fine structure (EXAFS), and transmission electron microscopy (TEM). The photocatalytic activity of the Pt-ZnO/ was evaluated by photocatalytic degradation of phenol in synthetic wastewater under UV-irradiation. Results obtained revealed that the surface area and the photocatalytic activity of the prepared samples were increased in the order ZnO/ < PAD: Pt-ZnO/ < img: Pt-ZnO/. The surface area decreased from 480 to 460 and 450 m2/g, while the efficiency of the phenol degradation increased from 80 to 85 and 100%, with the ZnO/, Img: Pt-ZnO-, and PAD: Pt-ZnO- samples, respectively.

Photocatalytic Degradation of Oxytetracycline by Photosensitive Materials and Toxicological Analysis by Caenorhabditis elegans

2019 ◽  
Vol 19 (11) ◽  
pp. 6924-6932 ◽  
Author(s):  
Qiaojie Yu ◽  
Tong Ouyang ◽  
Kefu Zhou ◽  
Changtang Chang
Keyword(s):  
Caenorhabditis Elegans ◽  
High Performance ◽  
Diffuse Reflectance Spectroscopy ◽  
Toxicity Testing ◽  
Degradation Process ◽  
Favorable Result ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Initial Ph ◽  
One Step

This study explored a facile one-step hydrothermal method of preparing a high-performance photocatalyst, namely, graphene-TiO2, for oxytetracycline (OTC) removal. The nanocomposites were characterized by Fourier transform infrared (FT-IR) spectroscopy, transmission electron microscopy, UV-Vis diffuse reflectance spectroscopy and X-ray diffraction (XRD). The photocatalytic properties of different graphene loading types and various OTC initial concentrations, temperatures, and initial pH values were investigated. Results showed that the material with 10% graphene content exhibited the best performance and removal efficiency (beyond 99%) of OTC within 180 min at 35 °C and pH 5.5. The effects of different reactive oxygen species scavengers on photodegradation and the contributions were evaluated, and a possible reaction mechanism was proposed. Caenorhabditis elegans was used for toxicity testing during the entire degradation process and achieved a favorable result.

scholarly journals Photodegradation of Methyl Orange Using Magnetically Recoverable AgBr@Ag3PO4/Fe3O4Photocatalyst under Visible Light

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Zhen Wang ◽  
Lu Yin ◽  
Ziwen Chen ◽  
Guowang Zhou ◽  
Huixiang Shi
Keyword(s):  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Visible Light ◽  
High Performance ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Transmission Electron ◽  
Activity Enhancement ◽  
Matching Band

A novel magnetically recoverable AgBr@Ag3PO4/Fe3O4hybrid was prepared by a simple deposition-precipitation approach and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-Vis diffuse reflectance spectroscopy (DRS). The results revealed that the photocatalytic activity and stability of AgBr@Ag3PO4/Fe3O4composite toward decomposition of methyl orange (MO) dye were superior to those of pure Ag3PO4under visible light irradiation. The photocatalytic activity enhancement of AgBr@Ag3PO4/Fe3O4is closely related to the efficient separation of electron-hole pairs derived from the matching band potentials between Ag3PO4and AgBr, as well as the good conductivity of Fe3O4. Moreover, the photocatalyst could be easily separated by applying an external magnetic field due to its magnetic property. The quenching effects of different scavengers proved that active h+and played the major role for the MO degradation. This work would provide new insight for the construction of visible light responsible photocatalysts with high performance, good stability, and recoverability.

scholarly journals Facile Synthesis of Uniform Mesoporous Nb2O5 Micro-Flowers for Enhancing Photodegradation of Methyl Orange

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3783
Author(s):  
Jian-Qing Qiu ◽  
Huan-Qing Xie ◽  
Ya-Hao Wang ◽  
Lan Yu ◽  
Fang-Yuan Wang ◽  
...  
Keyword(s):  
Methyl Orange ◽  
Active Sites ◽  
High Performance ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
Flower Structure ◽  
Electron Microscopies ◽  
Bet Method ◽  
One Step ◽  
Catalytic Active Sites

The removal of organic pollutants using green environmental photocatalytic degradation techniques urgently need high-performance catalysts. In this work, a facile one-step hydrothermal technique has been successfully applied to synthesize a Nb2O5 photocatalyst with uniform micro-flower structure for the degradation of methyl orange (MO) under UV irradiation. These nanocatalysts are characterized by transmission and scanning electron microscopies (TEM and SEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) method, and UV-Vis diffuse reflectance spectroscopy (DRS). It is found that the prepared Nb2O5 micro-flowers presents a good crystal phases and consist of 3D hierarchical nanosheets with 400–500 nm in diameter. The surface area is as large as 48.6 m2 g−1. Importantly, the Nb2O5 micro-flowers exhibit superior catalytic activity up to 99.9% for the photodegradation of MO within 20 mins, which is about 60-fold and 4-fold larger than that of without catalysts (W/O) and commercial TiO2 (P25) sample, respectively. This excellent performance may be attributed to 3D porous structure with abundant catalytic active sites.

scholarly journals Hydrothermal Synthesis of Iodine-Doped Nanoplates with Enhanced Visible and Ultraviolet-Induced Photocatalytic Activities

2012 ◽  
Vol 2012 ◽  
pp. 1-12 ◽  
Author(s):  
Jiang Zhang ◽  
Zheng-Hong Huang ◽  
Yong Xu ◽  
Feiyu Kang
Keyword(s):  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Oxygen Vacancies ◽  
Diffuse Reflectance Spectroscopy ◽  
Synergetic Effect ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Photocatalytic Activities

The iodine-doped Bi2WO6(I-BWO) photocatalyst was prepared via a hydrothermal method using potassium iodide as the source of iodine. The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM) and selected area electron diffraction (SAED), X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. The photocatalytic activity of I-BWO for the degradation of rhodamine B (RhB) was higher than that of pure BWO and I2-BWO regardless of visible light (>420 nm) or ultraviolet light (<400 nm) irradiation. The results of DRS analysis showed that the I-BWO and I2-BWO catalysts had narrower band gaps. XPS analysis proved that the multivalent iodine species including I0and were coadsorbed on the defect surface of Bi2WO6in I-BWO. The enhanced PL intensity revealed that a large number of defects of oxygen vacancies were formed by the doping of iodine. The enhanced photocatalytic activity of I-BWO for degradation of RhB was caused by the synergetic effect of a small crystalline size, a narrow band gap, and plenty of oxygen vacancies.

scholarly journals Silver Orthophosphate Immobilized on Flaky Layered Double Hydroxides as the Visible-Light-Driven Photocatalysts

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Xianlu Cui ◽  
Yaogang Li ◽  
Qinghong Zhang ◽  
Hongzhi Wang
Keyword(s):  
Visible Light ◽  
Diffuse Reflectance Spectroscopy ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Photocatalytic Activities ◽  
Visible Light Driven ◽  
Double Hydroxide ◽  
Double Hydroxides ◽  
Acid Red G

Flaky layered double hydroxide (FLDH) was prepared by the reconstruction of its oxide in alkali solution. The composites with FLDH/Ag3PO4mass ratios at 1.6 : 1 and 3 : 1 were fabricated by the coprecipitation method. The powders were characterized by X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscope, and UV-vis diffuse reflectance spectroscopy. The results indicated that the well-distributed Ag3PO4in a fine crystallite size was formed on the surface of FLDH. The photocatalytic activities of the Ag3PO4immobilized on FLDH were significantly enhanced for the degradation of acid red G under visible light irradiation compared to bare Ag3PO4. The composite with the FLDH/Ag3PO4mass ratio of 3 : 1 showed a higher photocatalytic efficiency.

CeO2/TiO2 Nanotubes Composites: Synthesis, Characterization, and Photocatalytic Properties

2012 ◽  
Vol 583 ◽  
pp. 86-90 ◽  
Author(s):  
Hai Bin Li ◽  
Xin Yong Li ◽  
Yan De Song ◽  
Shu Guang Chen ◽  
Ying Wang ◽  
...  
Keyword(s):  
Diffuse Reflectance Spectroscopy ◽  
Atomic Ratio ◽  
X Ray Diffraction ◽  
Hydrothermal Route ◽  
Electron Hole ◽  
Calcination Process ◽  
X Ray ◽  
Transmission Electron ◽  
Hole Recombination

TiO2nanotubes were prepared via a hydrothermal route. CeO2nanoparticles with diameters around 5nm were loaded onto the surface of TiO2nanotubes via a deposition approach followed by a calcination process. Transmission electron microscopy (TEM), X-ray diffraction (XRD), and UV-vis diffuse reflectance spectroscopy (UV-vis) were applied for the characterization of the as-prepared CeO2/TiO2nanotubes composites. The results show that CeO2particles are highly dispersed on the surface of TiO2nanotubes. The TiO2 nanotubes are modified to response to the visible light due to the combination with CeO2. The CeO2/TiO2nanotubes composites with a CeO2/TiO2atomic ratio of 2.5% show a further improvement on the photocatalytic activity for degradation of Rhodamine B in water. The presence of CeO2improves the light absorption of TiO2nanotubes and inhibits the electron-hole recombination.

One-Step Hydrothermal Synthesis of Bi2S3-TiO2-RGO Composites with Enhanced Visible Light Photocatalytic Activities

NANO ◽  
2018 ◽  
Vol 13 (05) ◽  
pp. 1850051 ◽  
Author(s):  
Yanan Li ◽  
Zhongmin Liu ◽  
Yaru Li ◽  
Yongchuan Wu ◽  
Jitao Chen ◽  
...  
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Photogenerated Electron ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Photocatalytic Ability ◽  
Transmission Electron ◽  
Light Region ◽  
Infrared Spectrometer ◽  
One Step

The Bi2S3-TiO2-RGO composites were synthesized by a facile one-step hydrothermal method and applied for the photocatalytic degradation of Rhodamine B (Rh B) under the visible light. The Bi2S3-TiO2-RGO composites were characterized by transmission electron microscopy, X-ray diffraction, Raman and Fourier transform infrared spectrometer. The results indicated that the Bi2S3-TiO2-RGO composites were successfully prepared, and Ti-O-C and S-C bonds were existing among Bi2S3, TiO2 as well as RGO. Furthermore, the photocatalytic ability of Bi2S3-TiO2-RGO composites was excellent under visible light due to its responding to the whole visible light region, low recombination rate of photogenerated electron–hole pairs and relatively negative conduction band. Rh B photocatalytic degradation rate was 99.5% after 50[Formula: see text]min and still could reach 98.4% after five cycles. Finally, a formation mechanism as well as a photocatalytic mechanism of Bi2S3-TiO2-RGO composites were proposed based on the experimental results.

scholarly journals Ce-Doped PANI/Fe3O4 Nanocomposites: Electrode Materials for Supercapattery

2021 ◽  
Vol 3 ◽  
Author(s):  
Subash Pandey ◽  
Shova Neupane ◽  
Dipak Kumar Gupta ◽  
Anju Kumari Das ◽  
Nabin Karki ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Electrode Material ◽  
High Performance ◽  
Electrode Materials ◽  
Specific Capacity ◽  
Maximum Energy ◽  
Potential Range ◽  
X Ray Diffraction ◽  
Active Electrode ◽  
Transmission Electron

In this study, we report on a combined approach to preparing an active electrode material for supercapattery application by making nanocomposites of Polyaniline/Cerium (PANI/Ce) with different weight percentages of magnetite (Fe3O4). Fourier-transform infrared spectroscopy (FTIR) and x-ray diffraction (XRD) analyses supported the interaction of PANI with Ce and the formation of the successful nanocomposite with magnetite nanoparticles. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses showed the uniform and porous morphology of the composites. Cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) were used to test the supercapattery behavior of the nanocomposite electrodes in 1.0 M H2SO4. It was found that the supercapattery electrode of PANI/Ce+7 wt.% Fe3O4 exhibited a specific capacity of 171 mAhg−1 in the potential range of −0.2 to 1.0 V at the current density of 2.5 Ag−1. Moreover, PANI/Ce+7 wt.% Fe3O4 revealed a power density of 376.6 Wkg−1 along with a maximum energy density of 25.4 Whkg−1 at 2.5 Ag−1. Further, the cyclic stability of PANI/Ce+7 wt.% Fe3O4 was found to be 96.0% after 5,000 cycles. The obtained results suggested that the PANI/Ce+Fe3O4 nanocomposite could be a promising electrode material candidate for high-performance supercapattery applications.

Sign in / Sign up

Export Citation Format

Share Document