scholarly journals Algae Biomass as a Potential Source of Liquid Fuels

Phycology ◽  
2021 ◽  
Vol 1 (2) ◽  
pp. 105-118
Author(s):  
Marcin Dębowski ◽  
Marcin Zieliński ◽  
Izabela Świca ◽  
Joanna Kazimierowicz
Keyword(s):  
Oil Recovery ◽  
Energy Use ◽  
Alcoholic Fermentation ◽  
Liquid Waste ◽  
Biofuel Production ◽  
Liquid Fuels ◽  
Algae Biomass ◽  
Bio Oil ◽  
Microalgae Biomass ◽  
Economic Analyses

Algae biomass is perceived as a prospective source of many types of biofuels, including biogas and biomethane produced in the anaerobic digestion process, ethanol from alcoholic fermentation, biodiesel synthesized from lipid reserve substances, and biohydrogen generated in photobiological transformations. Environmental and economic analyses as well as technological considerations indicate that methane fermentation integrated with bio-oil recovery is one of the most justified directions of energy use of microalgae biomass for energy purposes. A promising direction in the development of bioenergy systems based on the use of microalgae is their integration with waste and pollution neutralization technologies. The use of wastewater, another liquid waste, or flue gases can reduce the costs of biofuel production while having a measurable environmental effect.

scholarly journals Bio-Energetics and Utilization of Greenhouse Gases

10.12737/4938 ◽  
2014 ◽  
Vol 3 (3) ◽  
pp. 25-27 ◽  
Author(s):  
Хазанов ◽  
Grigoriy Khazanov ◽  
Курин ◽  
Valeriy Kurin ◽  
Апарушкина ◽  
...  
Keyword(s):  
Power Plant ◽  
Greenhouse Gases ◽  
Solid Fuel ◽  
Thermal Power Plant ◽  
Thermal Power ◽  
Hydrocarbon Fuel ◽  
Raw Material ◽  
Biofuel Production ◽  
Algae Biomass ◽  
Microalgae Biomass

The paper considers environmental problems of hydrocarbon fuel usage. The assessment of the area necessary for cultivation of algae biomass and its further use as solid fuel at thermal power plant has been carried out. Expediency of production of microalgae biomass in the process of photosynthesisas raw material for biofuel production is revealed.

MANUFACTURING GASEOUS PRODUCTS BY PYROLYSIS MICROALGAE BIOMASS

2019 ◽  
pp. 23-34
Author(s):  
N. I. Chernova ◽  
S. V. Kiseleva ◽  
O. M. Larina ◽  
G. A. Sytchev
Keyword(s):  
Raw Materials ◽  
Renewable Energy Sources ◽  
High Energy ◽  
Initial Mass ◽  
Solid Residue ◽  
Algae Biomass ◽  
Gaseous Products ◽  
Microalgae Biomass ◽  
Pyrolysis Liquid ◽  
Pyrolysis Gases

Algae biomass is considered as an alternative raw material for the production of biofuels. The search for new types of raw materials, including high-energy types of microalgae, remains relevant, since the share of motor fuels in the structure of the global fuel and energy balance remains consistently high (about 35%), and the price of oil is characterized by high volatility. The authors have considered the advantages of microalgae as sources of raw materials for fuel production. Biochemical and thermochemical conversion are proposed as technologies for their processing. This paper presents the results of the study of the pyrolysis of the biomass of clonal culture of blue-green microalgae / cyanobacteriumArthrospira platensis rsemsu 1/02-Pfrom the collection of the Research Laboratory of Renewable Energy Sources of the Lomonosov Moscow State University. An experiment to study the process of pyrolysis of microalgae biomass was carried out at the experimental facility of the Institute of High Temperatures RAS in pure nitrogen grade 6.0 to create an oxygen-free environment with a linear heating rate of 10 ºС / min from room temperature to 1000 ºС. The whole process of pyrolysis proceeded in the field of endothermy. The specific amounts of solid residue, pyrolysis liquid and gaseous products were experimentally determined. As a result of the pyrolysis of microalgae biomass weighing 15 g, the following products were obtained: 1) coal has the mass of the solid residue is 2.68 g, or 17.7% of the initial mass of the microalgae (while 9.3% of the initial mass of the microalgae remained in the reactor); 2) pyrolysis liquid – weight 3.3 g, or 21.9% of the initial weight; 3) non-condensable pyrolysis gases – weight 1.15 l. The specific volumetric gas yield (the amount of gas released from 1 kg of the starting material) was 0.076 Nm3/ kg. The analysis of the composition and specific volume yield of non-condensable pyrolysis gases formed in the process of pyrolysis, depending on temperature. It is shown that with increasing temperature, the proportion of highcalorie components of the gas mixture (hydrogen, methane and carbon monoxide) increases. The calorific value of the mixture of these gases has been estimated.

scholarly journals Conversion of biomass to biofuels and life cycle assessment: a review

2021 ◽  
Author(s):  
Ahmed I. Osman ◽  
Neha Mehta ◽  
Ahmed M. Elgarahy ◽  
Amer Al-Hinai ◽  
Ala’a H. Al-Muhtaseb ◽  
...  
Keyword(s):  
Life Cycle Assessment ◽  
Life Cycle ◽  
Energy Demand ◽  
Fossil Fuels ◽  
Biomass Conversion ◽  
Biofuel Production ◽  
Process Efficiency ◽  
Liquid Fuels ◽  
Thermochemical Processes ◽  
Lower Temperature

AbstractThe global energy demand is projected to rise by almost 28% by 2040 compared to current levels. Biomass is a promising energy source for producing either solid or liquid fuels. Biofuels are alternatives to fossil fuels to reduce anthropogenic greenhouse gas emissions. Nonetheless, policy decisions for biofuels should be based on evidence that biofuels are produced in a sustainable manner. To this end, life cycle assessment (LCA) provides information on environmental impacts associated with biofuel production chains. Here, we review advances in biomass conversion to biofuels and their environmental impact by life cycle assessment. Processes are gasification, combustion, pyrolysis, enzymatic hydrolysis routes and fermentation. Thermochemical processes are classified into low temperature, below 300 °C, and high temperature, higher than 300 °C, i.e. gasification, combustion and pyrolysis. Pyrolysis is promising because it operates at a relatively lower temperature of up to 500 °C, compared to gasification, which operates at 800–1300 °C. We focus on 1) the drawbacks and advantages of the thermochemical and biochemical conversion routes of biomass into various fuels and the possibility of integrating these routes for better process efficiency; 2) methodological approaches and key findings from 40 LCA studies on biomass to biofuel conversion pathways published from 2019 to 2021; and 3) bibliometric trends and knowledge gaps in biomass conversion into biofuels using thermochemical and biochemical routes. The integration of hydrothermal and biochemical routes is promising for the circular economy.

scholarly journals Simultaneous lipid biosynthesis and recovery for oleaginous yeast Yarrowia lipolytica

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Pratik Prashant Pawar ◽  
Annamma Anil Odaneth ◽  
Rajeshkumar Natwarlal Vadgama ◽  
Arvind Mallinath Lali
Keyword(s):  
Yarrowia Lipolytica ◽  
Oil Recovery ◽  
Oleaginous Yeast ◽  
Fermentation Broth ◽  
Continuous Production ◽  
Oil Production ◽  
Biofuel Production ◽  
Oil Yield ◽  
Microbial Oil

Abstract Background Recent trends in bioprocessing have underlined the significance of lignocellulosic biomass conversions for biofuel production. These conversions demand at least 90% energy upgradation of cellulosic sugars to generate renewable drop-in biofuel precursors (Heff/C ~ 2). Chemical methods fail to achieve this without substantial loss of carbon; whereas, oleaginous biological systems propose a greener upgradation route by producing oil from sugars with 30% theoretical yields. However, these oleaginous systems cannot compete with the commercial volumes of vegetable oils in terms of overall oil yields and productivities. One of the significant challenges in the commercial exploitation of these microbial oils lies in the inefficient recovery of the produced oil. This issue has been addressed using highly selective oil capturing agents (OCA), which allow a concomitant microbial oil production and in situ oil recovery process. Results Adsorbent-based oil capturing agents were employed for simultaneous in situ oil recovery in the fermentative production broths. Yarrowia lipolytica, a model oleaginous yeast, was milked incessantly for oil production over 380 h in a media comprising of glucose as a sole carbon and nutrient source. This was achieved by continuous online capture of extracellular oil from the aqueous media and also the cell surface, by fluidizing the fermentation broth over an adsorbent bed of oil capturing agents (OCA). A consistent oil yield of 0.33 g per g of glucose consumed, corresponding to theoretical oil yield over glucose, was achieved using this approach. While the incorporation of the OCA increased the oil content up to 89% with complete substrate consumptions, it also caused an overall process integration. Conclusion The nondisruptive oil capture mediated by an OCA helped in accomplishing a trade-off between microbial oil production and its recovery. This strategy helped in realizing theoretically efficient sugar-to-oil bioconversions in a continuous production process. The process, therefore, endorses a sustainable production of molecular drop-in equivalents through oleaginous yeasts, representing as an absolute microbial oil factory.

scholarly journals Controlling of two destructive zooplanktonic predators in Chlorella mass culture with surfactants

2021 ◽  
Vol 14 (1) ◽  
Author(s):  
Xiaobin Wen ◽  
Aoqi Zhang ◽  
Xiaoyan Zhu ◽  
Lin Liang ◽  
Yan Huo ◽  
...  
Keyword(s):  
Mass Culture ◽  
Chemical Method ◽  
Sodium Dodecyl ◽  
Sodium Dodecyl Benzene Sulfonate ◽  
Biofuel Production ◽  
Benzene Sulfonate ◽  
Microalgae Biomass ◽  
Mass Cultures ◽  
Dodecyl Benzene Sulfonate ◽  
Raceway Ponds

Abstract Background Predatory flagellates and ciliates are two common bio-contaminants which frequently cause biomass losses in Chlorella mass culture. Efficient and targeted ways are required to control these contaminations in Chlorella mass cultivation aiming for biofuel production especially. Results Five surfactants were tested for its ability to control bio-contaminations in Chlorella culture. All five surfactants were able to eliminate the contaminants at a proper concentration. Particularly the minimal effective concentrations of sodium dodecyl benzene sulfonate (SDBS) to completely eliminate Poterioochromonas sp. and Hemiurosomoida sp. were 8 and 10 mg L−1, respectively, yet the photosynthesis and viability of Chlorella was not significantly affected. These results were further validated in Chlorella mass cultures in 5, 20, and 200 m2 raceway ponds. Conclusions A chemical method using 10 mg L−1 SDBS as pesticide to control predatory flagellate or ciliate contamination in Chlorella mass culture was proposed. The method helps for a sustained microalgae biomass production and utilization, especially for biofuel production.

scholarly journals TESTING OF CHLORELLA/SCENEDESMUS MICROALGAE CONSORTIA FOR REMEDIATION OF WASTEWATER, CO₂ MITIGATION AND ALGAE BIOMASS FEASIBILITY FOR LIPID PRODUCTION

2014 ◽  
Vol 22 (2) ◽  
pp. 105-114 ◽  
Author(s):  
Judita Koreivienė ◽  
Robertas Valčiukas ◽  
Jūratė Karosienė ◽  
Pranas Baltrėnas
Keyword(s):  
Municipal Wastewater ◽  
Global Climate ◽  
Inorganic Nitrogen ◽  
Lipid Production ◽  
Single Species ◽  
Inorganic Phosphorus ◽  
Climatic Conditions ◽  
Biofuel Production ◽  
Treated Wastewater ◽  
Algae Biomass

Industry, transport and unsustainable agriculture result in the increased quantity of wastewater, release of nutrients and emission of carbon dioxide that promotes eutrophication of water bodies and global climate change. the application of microalgae for phycoremediation, their biomass use for human needs may increase sustainability and have a positive effect on the regional development. The experiments were carried out in order to establish the feasibility of treating the local municipal wastewater with microalgae consortia and their biomass potential for biofuel production. The results revealed that Chlorella/Scenedesmus consortium eliminated up to 99.7–99.9% of inorganic phosphorus and up to 88.6–96.4% of inorganic nitrogen from the wastewater within three weeks. The ammonium removal was more efficient than that of nitrate. Chlorella algae grew better in diluted, while Scenedesmus – in the concentrated wastewater. The consortium treated wastewater more efficiently than a single species. The maximum biomass (3.04 g/L) of algal consortium was estimated in concentrated wastewater. Algae accumulated 0.65–1.37 g of CO2/L per day in their biomass. Tus, Chlorella/Scenedesmus consortium is a promising tool for nutrients elimination from the local wastewater under the climatic conditions specific to Lithuania. However, none of the two species were able to accumulate lipids under the nitrogen starvation conditions.

scholarly journals Optimization of alcoholic fermentation using immobilized yeast cells in calcium alginate gel

2015 ◽  
pp. 207-218
Author(s):  
Jovana Djuran ◽  
Zorana Roncevic ◽  
Bojana Bajic ◽  
Sinisa Dodic ◽  
Jovana Grahovac ◽  
...  
Keyword(s):  
Sodium Alginate ◽  
Yeast Extract ◽  
Fossil Fuels ◽  
Alcoholic Fermentation ◽  
Immobilized Cells ◽  
Alginate Beads ◽  
Yeast Cells ◽  
Glucose Content ◽  
Alginate Concentration ◽  
Economic Analyses

Ethanol is an important industrial chemical with emerging potential as a biofuel to replace fossil fuels. In order to enhance the efficiency and yield of alcoholic fermentation, combined techniques such as cells immobilization and media optimization have been used. The aim of this study was the optimization of sodium alginate concentration and glucose and yeast extract content in the media for ethanol production with immobilized cells of Saccharomyces cerevisiae. Optimization of these parameters was attempted by using a Box-Behnken design using the response surface methodology. The obtained model predicts that the maximum ethanol content of 7.21% (v/v) is produced when the optimal values of sodium alginate concentration and initial content of glucose and yeast extract in the medium are 22.84 g/L, 196.42 g/L and 3.77 g/L, respectively. To minimize the number of yeast cells "eluted" from the alginate beads and residual glucose content in fermented media, additional two sets of optimization were made. The obtained results can be used for further techno-economic analyses of the process to select the optimum conditions of the fermentation process for industrial application.

scholarly journals BIOSORPTION OF METAL IONS Pb(II), Cu(II), AND Cd(II) ON Sargassum duplicatum IMMOBILIZED SILICA GEL MATRIX

2010 ◽  
Vol 6 (3) ◽  
pp. 245-250 ◽  
Author(s):  
Buhani Buhani ◽  
Suharso Suharso ◽  
Zipora Sembiring
Keyword(s):  
Metal Ions ◽  
Silica Gel ◽  
Functional Group ◽  
Adsorption Process ◽  
Liquid Waste ◽  
Batch Method ◽  
Algae Biomass ◽  
Adsorbent Surface ◽  
Physical And Chemical ◽  
Matrix Series

Sargassum duplicatum algae biomass is biological material which has a potency to be used as a biosorbent adsorb metal ions from industrial liquid waste, because it has effective functional group as a ligand. However, the ability of the algae biomass in adsorbing of heavy metal ions has some problem such as; tiny size, low density, and easy to be degradated by other microorganism. In addition, algae biomass can not be used directly in adsorption column for its application as the biosorbent. In order to improve physical and chemical prpperties of algae biomass, it needs to be immobilized on silica gel matrix. Series of experiment have been done, morphology analysis of adsorbent surface was performed by using Scanning Electron Microscopy (SEM) and adsorption process to examine the effectiveness of algae biomass immobilized in adsorbing Pb(II), Cu(II), and Cd(II) was performed using batch method at 27 °C. Concentration of metal was determined by using Atomic Absorption Spectrophotometer (AAS) and identification of functional group was conducted using Spectrophotometer Infrared (IR). Data obtained showed that interacting among metal ions with algae biomass is optimum at a range of 60 minutes. Adsorption energies of metal ions resulted from the interaction of metal ions with the functional group of -C=O group from carboxyl and amide on algae biomass and -Si-OH group from silica were at a range of 21.09-25.05 kJ/mole.   Keywords: biosorption, silica gel, Sargassum duplicatum, immobilization

scholarly journals Pyrolysis-GC/MS Analysis of Fast Growing Wood Macaranga Species

2021 ◽  
Vol 6 (1) ◽  
pp. 141-158
Author(s):  
R.R. Dirgarini J.N. Subagyono ◽  
Ying Qi ◽  
Alan L. Chaffee ◽  
Rudianto Amirta ◽  
Marc Marshall
Keyword(s):  
Thermal Degradation ◽  
Pyrolysis Temperature ◽  
Woody Biomass ◽  
Biofuel Production ◽  
Flash Pyrolysis ◽  
Fast Growing ◽  
Ms Analysis ◽  
Bio Oil ◽  
Different Temperatures ◽  
High Yields

Py-GC/MS analysis of six different species of fast growing Macaranga wood has been studied. Flash pyrolysis was conducted at different temperatures (250-850 oC) under a flow of helium followed by GC/MS analysis of the products. The total pyrolysis yields of the six different species of Macaranga were mostly between 40 and 90% within the range of pyrolysis temperature applied.  Pyrolysis of the woody biomass produced compounds which are mostly derived from thermal degradation or volatilization of lignin and cellulose/hemicellulose, the original major constituents of the biomass. The Py-GC/MS technique indicated that M. gigantea was the most potential species for biofuel production and the optimum pyrolysis temperature to produce high yields of bio-oil was 450 oC.

Utilisation of poultry industry wastes for liquid biofuel production via thermal and catalytic fast pyrolysis

2018 ◽  
Vol 37 (2) ◽  
pp. 157-167 ◽  
Author(s):  
Ismail Cem Kantarli ◽  
Stylianos D Stefanidis ◽  
Konstantinos G Kalogiannis ◽  
Angelos A Lappas
Keyword(s):  
Lignocellulosic Biomass ◽  
Poultry Litter ◽  
Fast Pyrolysis ◽  
Fixed Bed ◽  
Pilot Scale ◽  
Biofuel Production ◽  
Fluidised Bed ◽  
Nitrogenous Compounds ◽  
Catalytic Fast Pyrolysis ◽  
Bio Oil

The objective of this study was to examine the potential of poultry wastes to be used as feedstock in non-catalytic and catalytic fast pyrolysis processes, which is a continuation of our previous research on their conversion into biofuel via slow pyrolysis and hydrothermal conversion. Both poultry meal and poultry litter were examined, initially in a fixed bed bench-scale reactor using ZSM-5 and MgO as catalysts. Pyrolysis of poultry meal yielded high amounts of bio-oil, while pyrolysis of poultry litter yielded high amounts of solid residue owing to its high ash content. MgO was found to be more effective for the deoxygenation of bio-oil and reduction of undesirable compounds, by converting mainly the acids in the pyrolysis vapours of poultry meal into aliphatic hydrocarbons. ZSM-5 favoured the formation of both aromatic compounds and undesirable nitrogenous compounds. Overall, all bio-oil samples from the pyrolysis of poultry wastes contained relatively high amounts of nitrogen compared with bio-oils from lignocellulosic biomass, ca. 9 wt.% in the case of poultry meal and ca. 5–8 wt.% in the case of poultry litter. This was attributed to the high nitrogen content of the poultry wastes, unlike that of lignocellulosic biomass. Poultry meal yielded the highest amount of bio-oil and was selected as optimum feedstock to be scaled-up in a semi-pilot scale fluidised bed biomass pyrolysis unit with the ZSM-5 catalyst. Pyrolysis in the fluidised bed reactor was more efficient for deoxygenation of the bio-oil vapours, as evidenced from the lower oxygen content of the bio-oil.

Sign in / Sign up

Export Citation Format

Share Document