scholarly journals Enhancing the Mechanical and Thermal Properties of Epoxy Resin via Blending with Thermoplastic Polysulfone

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 461 ◽  
Author(s):  
Zeyu Sun ◽  
Lei Xu ◽  
Zhengguo Chen ◽  
Yuhao Wang ◽  
Rogers Tusiime ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Epoxy Resin ◽  
Mechanical Tests ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Dsc Studies ◽  
Curing Reaction ◽  
Dynamic Mechanical Thermal Analyzer ◽  
Ft Ir ◽  
Epoxy Blends

Efficient enhancement of the toughness of epoxy resins has been a bottleneck for expanding their suitability for advanced applications. Here, polysulfone (PSF) was adopted to toughen and modify the epoxy. The influences of PSF on the mechanical and thermal properties of the epoxy resin were systematically studied by optical microscopy, Fourier transform infrared spectrometer (FT-IR), differential scanning calorimetry (DSC), thermogravimetric analyzer (TG), dynamic mechanical thermal analyzer (DMA), mechanical tests and scanning electron microscope (SEM). The dissolution experimental results showed that PSF presents a good compatibility with the epoxy resin and could be well dissolved under controlled conditions. The introduction of PSF was found to promote the curing reaction of the epoxy resin without participating in the curing reaction and changing the curing mechanism as revealed by the FT-IR and DSC studies. The mechanical properties of PSF/epoxy resin blends showed that the fracture toughness and impact strength were significantly improved, which could be attributed to the bicontinuous phase structure of PSF/epoxy blends. Representative phase structures resulted from the reaction induced phase separation process were clearly observed in the PSF/epoxy blends during the curing process of epoxy resin, which presented dispersed particles, bicontinuous and phase inverted structures with the increase of the PSF content. Our work further confirmed that the thermal stability of the PSF/epoxy blends was slightly increased compared to that of the pure epoxy resin, mainly due to the good heat resistance of the PSF component.

scholarly journals Reaction Mechanism and Mechanical Property Improvement of Poly(Lactic Acid) Reactive Blending with Epoxy Resin

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2429
Author(s):  
Krittameth Kiatiporntipthak ◽  
Nanthicha Thajai ◽  
Thidarat Kanthiya ◽  
Pornchai Rachtanapun ◽  
Noppol Leksawasdi ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Epoxy Resin ◽  
Softening Temperature ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Nanoparticle Dispersion ◽  
Reactive Blending ◽  
Partial Miscibility ◽  
Epoxy Blends ◽  
Epoxy Content

Polylactic acid (PLA) was melt-blended with epoxy resin to study the effects of the reaction on the mechanical and thermal properties of the PLA. The addition of 0.5% (wt/wt) epoxy to PLA increased the maximum tensile strength of PLA (57.5 MPa) to 67 MPa, whereas the 20% epoxy improved the elongation at break to 12%, due to crosslinking caused by the epoxy reaction. The morphology of the PLA/epoxy blends showed epoxy nanoparticle dispersion in the PLA matrix that presented a smooth fracture surface with a high epoxy content. The glass transition temperature of PLA decreased with an increasing epoxy content owing to the partial miscibility between PLA and the epoxy resin. The Vicat softening temperature of the PLA was 59 °C and increased to 64.6 °C for 0.5% epoxy. NMR confirmed the reaction between the -COOH groups of PLA and the epoxy groups of the epoxy resin. This reaction, and partial miscibility of the PLA/epoxy blend, improved the interfacial crosslinking, morphology, thermal properties, and mechanical properties of the blends.

scholarly journals Effects of EPON on Mechanical and Thermal Properties of Epoxy Resins

2008 ◽  
Vol 47-50 ◽  
pp. 536-539 ◽  
Author(s):  
H. Ku ◽  
F. Cardona ◽  
D. Rogers ◽  
A. Vandenbroucke
Keyword(s):  
Thermal Properties ◽  
Epoxy Resin ◽  
Structural Engineering ◽  
Epoxy Composite ◽  
Low Cost ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Bending Tests ◽  
Three Point Bending ◽  
The Cost

Low cost composite materials are widely used in civil and structural engineering applications. This project uses EPON to plasticize a commonly used resin, epoxy resin to lower the cost of the composite and to find out the mechanical and thermal properties of the plasticized epoxy resin to see if it is suitable for the said applications. Three point bending tests were carried out to evaluate the flexural properties of the plasticized resins. Differential scanning calorimetry and dynamic mechanical thermal analysis are used to evaluate the thermal properties of the plasticized epoxy resin. The study with epoxy and EPON showed that the mechanical properties of the epoxy composite were lowered but its ability to dissipate energy increased because of its improved thermal properties. As EPON is much cheaper that epoxy resin, the composite produced is therefore cheaper and provided the service requirements were not so demanding, it can be used in the said applications.

Mechanical and thermal characterization of grafted PP-NCC nanocomposites

2019 ◽  
pp. 089270571987822
Author(s):  
Saud Aldajah ◽  
Mohammad Y Al-Haik ◽  
Waseem Siddique ◽  
Mohammad M Kabir ◽  
Yousef Haik
Keyword(s):  
Thermal Properties ◽  
Interfacial Adhesion ◽  
Thermal Characterization ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Three Point Bending ◽  
Twin Screw ◽  
Thermal Stability Of

This study reveals the enhancement of mechanical and thermal properties of maleic anhydride-grafted polypropylene (PP- g-MA) with the addition of nanocrystalline cellulose (NCC). A nanocomposite was manufactured by blending various percentages of PP, MA, and NCC nanoparticles by means of a twin-screw extruder. The influence of varying the percentages of NCC on the mechanical and thermal behavior of the nanocomposite was studied by performing three-point bending, nanoindentation, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and Fourier-transform infrared (FTIR) spectroscopy tests. The novelty of this study stems on the NCC nanoparticles and their ability to enhance the mechanical and thermal properties of PP. Three-point bending and nanoindentation tests revealed improvement in the mechanical properties in terms of strength, modulus, and hardness of the PP- g-MA nanocomposites as the addition of NCC increased. SEM showed homogeneity between the mixtures which proved the presence of interfacial adhesion between the PP- g-MA incorporated with NCC nanoparticles that was confirmed by the FTIR results. DSC and TGA measurements showed that the thermal stability of the nanocomposites was not compromised due to the addition of the coupling agent and reinforced nanoparticles.

Effects of Steam Heat and Dry Heat Sterilization on Thermal and Mechanical Properties of Nylon and Policarbonate in Fabrication with Fused Filament

2021 ◽  
Vol 891 ◽  
pp. 150-163
Author(s):  
Jorge Mauricio Fuentes ◽  
Omar Flor Unda ◽  
Santiago Ferrandiz ◽  
Franyelit Suarez
Keyword(s):  
Mechanical Properties ◽  
Thermomechanical Analysis ◽  
Mechanical Tests ◽  
Effect Of Temperature ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Thermal Tests ◽  
Dry Heat ◽  
Izod Impact ◽  
Steam Heat

In this article presents evidence about performance of mechanical properties of polycarbonate and nylon materials, which are used in the additive manufacturing by deposition of molten material and that have been subjected to sterilization processes by moist heat at 121°C and dry heat at 140°C. This study provides useful information to consider the use of these materials in sanitary and sterile settings. Mechanical tests of tensile, flex, hardness, Izod impact, thermal tests in Differential Scanning Calorimetry DSC, Thermomechanical analysis TMA and Scanning Electron Microscopy SEM were performed. It is concluded that the mechanical and thermal properties have not been altered through the effect of temperature in sterilization processes.

The influence of adding long basalt fiber on the mechanical and thermal properties of composites based on poly(oxymethylene)

2018 ◽  
Vol 33 (4) ◽  
pp. 435-450 ◽  
Author(s):  
Patrycja Bazan ◽  
Stanisław Kuciel ◽  
Mariola Sądej
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Average Length ◽  
Flexural Modulus ◽  
Basalt Fiber ◽  
Charpy Impact ◽  
Mechanical And Thermal Properties ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Atr Spectroscopy

The work has evaluated the possibility of the potential reinforcing of poly(oxymethylene) (POM) by basalt fibers (BFs) and influence of BFs addition on thermal properties. Two types of composites were produced by injection molding. There were 20 and 40 wt% long BFs content with an average length of 1 mm. The samples were made without using a compatibilizer. In the experimental part, the basic mechanical properties (tensile strength, modulus of elasticity, strain at break, flexural modulus, flexural strength, and deflection at 3.5% strain) of composites based on POM were determined. Tensile properties were also evaluated at three temperatures −20°C, 20°C, and 80°C. The density and Charpy impact of the produced composites were also examined. The influence of water absorption on mechanical properties was investigated. Thermal properties were conducted by the differential scanning calorimetry, thermal gravimetric analysis, and fourier transform infrared (FTIR)-attenuation total reflection (ATR) spectroscopy analysis. In order to make reference to the effects of reinforcement and determine the structure characteristics, scanning electron microscopy images were taken. The addition of 20 and 40 wt% by weight of fibers increases the strength and the stiffness of such composites by more than 30–70% in the range scale of temperature. Manufactured composites show higher thermal and dimensional stability in relation to neat POM.

scholarly journals Preparation and Characterization of Green Epoxy Resin Composites and Its Use in Corrosion Resistance

2018 ◽  
Author(s):  
Abbas Hassan Faris
Keyword(s):  
Bisphenol A ◽  
Epoxy Resin ◽  
Electrolyte Solutions ◽  
Kraft Lignin ◽  
Diglycidyl Ether ◽  
Kraft Pulping ◽  
Palm Tree ◽  
Scanning Calorimetry ◽  
Ft Ir ◽  
Nano Titanium Dioxide

In this work, appropriate alternative for diglycidyl ether bisphenol A (DGEBA) was found to avoid the destructive effects of bisphenol A. Lignin, an aromatic compound from palm tree leaves, was used as a renewable material to synthesize a bio-based epoxy resin. Lignin extracted using Kraft pulping process. Kraft Lignin was epoxidized with epichlorohydrin in alkaline medium. Nano-titanium dioxide was used as filler with ratio of 10% to prepare the green epoxy composite. The structure of the Kraft lignin and lignin-based epoxy resin was proven via Infrared spectra (FT-IR) were recorded using solid KBr disk by testing Shimadzu (FT-IR-8300) spectrophotometer. The thermal properties of the curing process of lignin-based epoxy resin and composite were investigate using Differential scanning calorimetry (DSC) analysis. Potentiodynamic measurements data revealed that the anti-corrosion performance of the lignin based epoxy resin. The study demonstrates successful of epoxidation of Kraft lignin. In addition, lignin based eopxy resin showed effective inhibitor for carbon steel in 3.5 wt. % NaCl electrolyte solutions

Comparative study of different polymerically-modified clays on curing reaction and thermal properties of epoxy resin

2011 ◽  
Vol 516 (1-2) ◽  
pp. 13-18 ◽  
Author(s):  
Yuanhua Xu ◽  
Hua Peng ◽  
Xi Wang ◽  
Shengpei Su
Keyword(s):  
Thermal Properties ◽  
Comparative Study ◽  
Epoxy Resin ◽  
Modified Clays ◽  
Curing Reaction

Evaluation of mechanical and thermal properties of modified epoxy resin by using acacia catechu particles

2019 ◽  
Vol 225 ◽  
pp. 239-246 ◽  
Author(s):  
Ahmer Hussain Shah ◽  
Xiao Li ◽  
Xiaodong Xu ◽  
Abdul Qadeer Dayo ◽  
Wen-bin Liu ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Epoxy Resin ◽  
Mechanical And Thermal Properties ◽  
Acacia Catechu ◽  
Modified Epoxy

scholarly journals Mechanical and Thermal Characterization of Natural Intralaminar Hybrid Composites Based on Sisal

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 866 ◽  
Author(s):  
Alexandre L. Pereira ◽  
Mariana D. Banea ◽  
Jorge S.S. Neto ◽  
Daniel K.K. Cavalcanti
Keyword(s):  
Thermal Properties ◽  
Natural Fiber ◽  
Hybrid Composites ◽  
Thermal Characterization ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Sem Images ◽  
The Matrix ◽  
American Society ◽  
Curaua Fibers

The main objective of this work was to investigate the effect of hybridization on the mechanical and thermal properties of intralaminar natural fiber-reinforced hybrid composites based on sisal. Ramie, sisal and curauá fibers were selected as natural fiber reinforcements for the epoxy matrix based composites, which were produced by the hand lay-up technique. Tensile, flexural and impact tests were carried out according to American society for testing and materials (ASTM) standards to characterize the hybrid composites, while differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to evaluate the thermal properties. It was found that the mechanical properties are improved by hybridization of sisal based composites. The thermal analysis showed that the hybridization did not significantly affect the thermal stability of the composites. A scanning electron microscopy (SEM) was used to examine the fracture surface of the tested specimens. The SEM images showed a brittle fracture of the matrix and fiber breakage near the matrix.

Sign in / Sign up

Export Citation Format

Share Document