scholarly journals Cobalt Oxide Nanograins and Silver Nanoparticles Decorated Fibrous Polyaniline Nanocomposite as Battery-Type Electrode for High Performance Supercapattery

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2816
Author(s):  
Javed Iqbal ◽  
Arshid Numan ◽  
Mohammad Omaish Ansari ◽  
Rashida Jafer ◽  
Priyanka R. Jagadish ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cobalt Oxide ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Oxidative Polymerization ◽  
Specific Capacity ◽  
Cyclic Stability ◽  
Structural Studies ◽  
X Ray ◽  
Ternary Nanocomposite

In this study, silver (Ag) and cobalt oxide (Co3O4) decorated polyaniline (PANI) fibers were prepared by the combination of in-situ aniline oxidative polymerization and the hydrothermal methodology. The morphology of the prepared Ag/Co3O4@PANI ternary nanocomposite was studied by scanning electron microscopy and transmission electron microscopy, while the structural studies were carried out by X-ray diffraction and X-ray photoelectron spectroscopy. The morphological characterization revealed fibrous shaped PANI, coated with Ag and Co3O4 nanograins, while the structural studies revealed high purity, good crystallinity, and slight interactions among the constituents of the Ag/Co3O4@PANI ternary nanocomposite. The electrochemical performance studies revealed the enhanced performance of the Ag/Co3O4@PANI nanocomposite due to the synergistic/additional effect of Ag, Co3O4 and PANI compared to pure PANI and Co3O4@PANI. The addition of the Ag and Co3O4 provided an extended site for faradaic reactions leading to the high specific capacity. The Ag/Co3O4@PANI ternary nanocomposite exhibited an excellent specific capacity of 262.62 C g−1 at a scan rate of 3 mV s−1. The maximum energy and power density were found to be 14.01 Wh kg−1 and 165.00 W kg−1, respectively. The cyclic stability of supercapattery (Ag/Co3O4@PANI//activated carbon) consisting of a battery type electrode demonstrated a gradual increase in specific capacity with a continuous charge–discharge cycle until ~1000 cycles, then remained stable until 2500 cycles and later started decreasing, thereby showing the cyclic stability of 121.03% of its initial value after 3500 cycles.

scholarly journals Hydrothermally Assisted Synthesis of Porous Polyaniline@Carbon Nanotubes–Manganese Dioxide Ternary Composite for Potential Application in Supercapattery

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2918
Author(s):  
Javed Iqbal ◽  
Mohammad Omaish Ansari ◽  
Arshid Numan ◽  
S. Wageh ◽  
Ahmed Al-Ghamdi ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Manganese Dioxide ◽  
Photoelectron Spectroscopy ◽  
Oxidative Polymerization ◽  
Specific Capacity ◽  
Cyclic Stability ◽  
X Ray Diffraction ◽  
Ternary Composite ◽  
X Ray ◽  
Synthesis Methodology

In this study, ternary composites of polyaniline (PANI) with manganese dioxide (MnO2) nanorods and carbon nanotubes (CNTs) were prepared by employing a hydrothermal methodology and in-situ oxidative polymerization of aniline. The morphological analysis by scanning electron microscopy showed that the MnO2 possessed nanorod like structures in its pristine form, while in the ternary PANI@CNT/MnO2 composite, coating of PANI over CNT/MnO2, rods/tubes were evidently seen. The structural analysis by X-ray diffraction and X-ray photoelectron spectroscopy showed peaks corresponding to MnO2, PANI and CNT, which suggested efficacy of the synthesis methodology. The electrochemical performance in contrast to individual components revealed the enhanced performance of PANI@CNT/MnO2 composite due to the synergistic/additional effect of PANI, CNT and MnO2 compared to pure MnO2, PANI and PANI@CNT. The PANI@CNT/MnO2 ternary composite exhibited an excellent specific capacity of 143.26 C g−1 at a scan rate of 3 mV s−1. The cyclic stability of the supercapattery (PANI@CNT/MnO2/activated carbon)—consisting of a battery type electrode—demonstrated a gradual increase in specific capacity with continuous charge–discharge over ~1000 cycles and showed a cyclic stability of 119% compared to its initial value after 3500 cycles.

scholarly journals Fabrication of Strontium Bismuth Oxides as Novel Battery-Type Electrode Materials for High-Performance Supercapacitors

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Yinghui Han ◽  
Le Li ◽  
Yunpeng Liu ◽  
Xue Li ◽  
Xiaohan Qi ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Electrode Materials ◽  
Specific Capacity ◽  
Structural Features ◽  
High Electron ◽  
Strontium Content ◽  
X Ray ◽  
Bismuth Oxides ◽  
Improved Performance

A simple and efficient process method for the preparation of strontium bismuth oxides (SBOs) via an impregnation-calcination method is presented. The synthesized active materials are characterized using X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy. The electrochemical performance of the as-synthesized SBO samples is observed to decrease gradually as the strontium content is increased from 25% to 50%. The SBO sample with a Sr/Bi ratio of 1 : 3 shows the highest specific capacitance of 1228.7 F g−1 (specific capacity of 204.8 mAh g−1) at a current density of 1 A g−1 and a good cycling stability (75.1%) over 3000 charge-discharge cycles. The improved performance of the supercapacitors can be attributed to the unique structural features resulting from the addition of appropriate portions of Sr, which supports high electron conductivity and rapid ion/electron transport within the electrode and at the electrode/electrolyte interface. All the results show that the SBOs have considerable potential for use as high-performance battery-type electrodes in supercapacitors.

scholarly journals Photocatalytic degradation of deoxynivalenol over dendritic-like α-Fe2O3 under visible light irradiation

Toxins ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 105 ◽  
Author(s):  
Huiting Wang ◽  
Jin Mao ◽  
Zhaowei Zhang ◽  
Qi Zhang ◽  
Liangxiao Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Visible Light ◽  
Photocatalytic Degradation ◽  
Visible Light Irradiation ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Synthesis Method ◽  
Light Irradiation ◽  
Trichothecene Mycotoxin ◽  
X Ray

Deoxynivalenol (DON) is a secondary metabolite produced by Fusarium, which is a trichothecene mycotoxin. As the main mycotoxin with high toxicity, wheat, barley, corn and their products are susceptible to contamination of DON. Due to the stability of this mycotoxin, traditional methods for DON reduction often require a strong oxidant, high temperature and high pressure with more energy consumption. Therefore, exploring green, efficient and environmentally friendly ways to degrade or reduce DON is a meaningful and challenging issue. Herein, a dendritic-like α-Fe2O3 was successfully prepared using a facile hydrothermal synthesis method at 160 °C, which was systematically characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). It was found that dendritic-like α-Fe2O3 showed superior activity for the photocatalytic degradation of DON in aqueous solution under visible light irradiation (λ > 420 nm) and 90.3% DON (initial concentration of 4.0 μg/mL) could be reduced in 2 h. Most of all, the main possible intermediate products were proposed through high performance liquid chromatography-mass spectrometry (HPLC-MS) after the photocatalytic treatment. This work not only provides a green and promising way to mitigate mycotoxin contamination but also may present useful information for future studies.

scholarly journals Ni2P/rGO/NF Nanosheets As a Bifunctional High-Performance Electrocatalyst for Water Splitting

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 744 ◽  
Author(s):  
Jinyu Huang ◽  
Feifei Li ◽  
Baozhong Liu ◽  
Peng Zhang
Keyword(s):  
Electron Microscopy ◽  
Water Splitting ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
High Efficiency ◽  
Splitting Method ◽  
Bifunctional Catalyst ◽  
Strong Activity ◽  
X Ray ◽  
Transmission Electron

The hydrogen generated via the water splitting method is restricted by the high level of theoretical potential exhibited by the anode. The work focuses on synthesizing a bifunctional catalyst with a high efficiency, that is, a nickel phosphide doped with the reduced graphene oxide nanosheets supported on the Ni foam (Ni2P/rGO/NF), via the hydrothermal approach together with the calcination approach specific to the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER). The Raman, X-Ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscope (TEM), Scanning Electron Microscopy (SEM), High-Resolution Transmission Electron Microscopy (HRTEM), as well as elemental mapping, are adopted to study the composition and morphology possessed by Ni2P/rGO/NF. The electrochemical testing is performed by constructing a parallel two-electrode electrolyzer (Ni2P/rGO/NF||Ni2P/rGO/NF). Ni2P/rGO/NF||Ni2P/rGO/NF needs a voltage of only 1.676 V for driving 10 mA/cm2, which is extremely close to Pt/C/NF||IrO2/NF (1.502 V). It is possible to maintain the current density for no less than 30 hours. It can be demonstrated that Ni2P/rGO/NF||Ni2P/rGO/NF has commercial feasibility, relying on the strong activity and high stability.

scholarly journals Fabrication of BaTiO3-Loaded Graphene Nanosheets-Based Polyarylene Ether Nitrile Nanocomposites with Enhanced Dielectric and Crystallization Properties

Nanomaterials ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1667 ◽  
Author(s):  
Shuning Liu ◽  
Chenchen Liu ◽  
Yong You ◽  
Yajie Wang ◽  
Renbo Wei ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Dielectric Constant ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Graphene Nanosheets ◽  
Zinc Phthalocyanine ◽  
Organic Layer ◽  
X Ray ◽  
Polyarylene Ether Nitrile ◽  
Crystallization Properties

In this paper, barium titanate@zinc phthalocyanine (BT@ZnPc) and graphene oxide (GO) hybrids (BT@ZnPc-GO) connected by calcium ions are prepared by electrostatic adsorption, and then introduced into polyarylene ether nitrile (PEN) to obtain composites with enhanced dielectric and crystallization properties. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) results confirm the successful fabrication of the BT@ZnPc-GO. BT@ZnPc-GO and PEN composites (BT@ZnPc-GO/PENs) are obtained through the solution-casting method. BT@ZnPc-GO demonstrates well compatibility with PEN due to its unique structure and the organic layer of ZnPc at the periphery of BT. On the other hand, BT and GO contribute a high dielectric constant of the composites obtained. In addition, the BT@ZnPc-GO can be used as a nucleating agent to promote the crystallization of the nanocomposites. As a result, The BT@ZnPc-GO/PEN exhibits a dielectric constant of 6.4 at 1 kHz and crystallinity of 21.03% after being isothermally treated at 280 °C for 2 h at the GO content of 0.75 wt %. All these results indicate that the hybrid nanofiller BT@ZnPc-GO can be an effective additive for preparing high-performance PEN-based nanocomposites.

Synthesis of MoO3/V2O5/C Composite as Novel Anode for Li-Ion Battery Application

2020 ◽  
Vol 20 (5) ◽  
pp. 2911-2916
Author(s):  
Zhen Zhang ◽  
Xiao Chen ◽  
Guangxue Zhang ◽  
Chuanqi Feng
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Specific Capacity ◽  
Lithium Ion ◽  
Li Ion Battery ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Li Ion ◽  
Battery Application

The MoO3/V2O5/C, MoO3/C and V2O5/C are synthesized by electrospinning combined with heat treatment. These samples are characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy and thermogravimetric analysis (TG) techniques. The results show that sample MoO3/V2O5/C is a composite composed from MoO3, V2O5 and carbon. It takes on morphology of the nanofibers with the diameter of 200~500 nm. The TG analysis result showed that the carbon content in the composite is about 40.63%. Electrochemical properties for these samples are studied. When current density is 0.2 A g−1, the MoO3/V2O5/C could retain the specific capacity of 737.6 mAh g−1 after 200 cycles and its coulomb efficiency is 92.99%, which proves that MoO3/V2O5/C has better electrochemical performance than that of MoO3/C and V2O5/C. The EIS and linear Warburg coefficient analysis results show that the MoO3/V2O5/C has larger Li+ diffusion coefficient and superior conductivity than those of MoO3/C or V2O5/C. So MoO3/V2O5/C is a promising anode material for lithium ion battery application.

scholarly journals Incorporating N Atoms into SnO2 Nanostructure as an Approach to Enhance Gas Sensing Property for Acetone

Nanomaterials ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 445 ◽  
Author(s):  
Xiangfeng Guan ◽  
Yongjing Wang ◽  
Peihui Luo ◽  
Yunlong Yu ◽  
Dagui Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Gas Sensor ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Gas Sensing ◽  
Diffuse Reflectance Spectroscopy ◽  
Limit Of Detection ◽  
Low Cost ◽  
X Ray ◽  
Sno2 Nanostructure

The development of high-performance acetone gas sensor is of great significance for environmental protection and personal safety. SnO2 has been intensively applied in chemical sensing areas, because of its low cost, high mobility of electrons, and good chemical stability. Herein, we incorporated nitrogen atoms into the SnO2 nanostructure by simple solvothermal and subsequent calcination to improve gas sensing property for acetone. The crystallization, morphology, element composition, and microstructure of as-prepared products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Electron paramagnetic resonance (EPR), Raman spectroscopy, UV–visible diffuse reflectance spectroscopy (UV–vis DRS), and the Brunauer–Emmett–Teller (BET) method. It has been found that N-incorporating resulted in decreased crystallite size, reduced band-gap width, increased surface oxygen vacancies, enlarged surface area, and narrowed pore size distribution. When evaluated as gas sensor, nitrogen-incorporated SnO2 nanostructure exhibited excellent sensitivity for acetone gas at the optimal operating temperature of 300 °C with high sensor response (Rair/Rgas − 1 = 357) and low limit of detection (7 ppb). The nitrogen-incorporated SnO2 gas sensor shows a good selectivity to acetone in the interfering gases of benzene, toluene, ethylbenzene, hydrogen, and methane. Furthermore, the possible gas-sensing mechanism of N-incorporated SnO2 toward acetone has been carefully discussed.

ZnS NANOFLOWERS ON GRAPHENE FOR USE AS A HIGH-PERFORMANCE PHOTOCATALYST

NANO ◽  
2014 ◽  
Vol 09 (08) ◽  
pp. 1450097 ◽  
Author(s):  
ZENG BIN ◽  
LONG HUI
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Dye Degradation ◽  
Uv Light ◽  
Xps Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Photocatalytic Activities ◽  
Potential Applications

The nanocomposites of graphene loaded– ZnS nanoflowers (GR– ZnS ) had been successfully prepared. Materials were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectra (FTIR), photoluminescence (PL) and X-ray photoelectron spectroscopy (XPS) spectra. A possible formation mechanism of this architecture was proposed. The experimental results revealed that these nanoflowers exhibited excellent UV-light photocatalytic activities for pollutant methyl orange (MO) dye degradation. These new nanostructures were expected to show considerable potential applications in the water treatment.

Influence of pyrrole feeding ratios on physicochemical characteristics of high-performance multilayered PPy/PVC/PDA@FG-NH2 nanocomposites

2019 ◽  
Vol 33 (10) ◽  
pp. 1358-1382
Author(s):  
Asima Naz ◽  
Rabia Sattar ◽  
Muhammad Siddiq ◽  
Muhammad Abid Zia
Keyword(s):  
Conjugated Polymers ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Oxidative Polymerization ◽  
Physicochemical Characteristics ◽  
Layer By Layer ◽  
X Ray ◽  
Melting And Crystallization ◽  
Scanning Electron

Nanocomposites of conjugated polymers polypyrrole (PPy) and polyvinyl chloride (PVC) as matrices and 1,4-phenylenediamine (PDA) as a linker with amine functional graphite (FG-NH2) as filler have been efficiently fabricated using in situ oxidative polymerization, and the effect of various mass ratios on physicochemical characteristics of prepared nanocomposite was investigated. The layer-by-layer oxidative polymerization of various matrices on host filler surface is confirmed by Fourier transform infrared, energy dispersive X-ray, and X-ray photoelectron spectroscopy examinations. Field emission scanning electron microscopy revealed fibrillary morphology of obtained nanocomposites. Thermal stability, glass transition temperature, and melting and crystallization temperature of the nanocomposites were increased with the incorporation of modified graphite. Brunauer–Emmett–Teller analysis explored the improved adsorption capacity (128 cm3 g−1) of the nanocomposite with higher feeding ratio of pyrrole. The influence of FG-NH2 and pyrrole on electrical conductivity performance of composites was also investigated. Functionalized graphite in the resultant PPy/PVC/PDA@FG-NH2 nanocomposites played an important role in forming conducting network in PPy matrix indicating synergistic effect between PPy and FG-NH2.

scholarly journals Effect of Time on a Hierarchical Corn Skeleton-Like Composite of CoO@ZnO as Capacitive Electrode Material for High Specific Performance Supercapacitors

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3285 ◽  
Author(s):  
Yedluri Kumar ◽  
Hee-Je Kim
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Xrd Analysis ◽  
Cycling Performance ◽  
Energy Storage Devices ◽  
Tem Analysis ◽  
X Ray ◽  
Potential Applications ◽  
Oxygen Groups

CoO–ZnO-based composites have attracted considerable attention for the development of energy storage devices because of their multifunctional characterization and ease of integration with existing components. This paper reports the synthesis of CoO@ZnO (CZ) nanostructures on Ni foam by the chemical bath deposition (CBD) method for facile and eco-friendly supercapacitor applications. The formation of a CoO@ZnO electrode functioned with cobalt, zinc, nickel and oxygen groups was confirmed by X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), low and high-resolution scanning electron microscopy (SEM), and transmission electron microscopy (TEM) analysis. The as-synthesized hierarchical nanocorn skeleton-like structure of a CoO@ZnO-3h (CZ3h) electrode delivered a higher specific capacitance (Cs) of 1136 F/g at 3 A/g with outstanding cycling performance, showing 98.3% capacitance retention over 3000 cycles in an aqueous 2 M KOH electrolyte solution. This retention was significantly better than that of other prepared electrodes, such as CoO, ZnO, CoO@ZnO-1h (CZ1h), and CoO@ZnO-7h (CZ7h) (274 F/g, 383 F/g, 240 F/g and 537 F/g). This outstanding performance was attributed to the excellent surface morphology of CZ3h, which is responsible for the rapid electron/ion transfer between the electrolyte and the electrode surface area. The enhanced features of the CZ3h electrode highlight potential applications in high performance supercapacitors, solar cells, photocatalysis, and electrocatalysis.

Sign in / Sign up

Export Citation Format

Share Document