scholarly journals Fabrication of Strontium Bismuth Oxides as Novel Battery-Type Electrode Materials for High-Performance Supercapacitors

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Yinghui Han ◽  
Le Li ◽  
Yunpeng Liu ◽  
Xue Li ◽  
Xiaohan Qi ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Electrode Materials ◽  
Specific Capacity ◽  
Structural Features ◽  
High Electron ◽  
Strontium Content ◽  
X Ray ◽  
Bismuth Oxides ◽  
Improved Performance

A simple and efficient process method for the preparation of strontium bismuth oxides (SBOs) via an impregnation-calcination method is presented. The synthesized active materials are characterized using X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy. The electrochemical performance of the as-synthesized SBO samples is observed to decrease gradually as the strontium content is increased from 25% to 50%. The SBO sample with a Sr/Bi ratio of 1 : 3 shows the highest specific capacitance of 1228.7 F g−1 (specific capacity of 204.8 mAh g−1) at a current density of 1 A g−1 and a good cycling stability (75.1%) over 3000 charge-discharge cycles. The improved performance of the supercapacitors can be attributed to the unique structural features resulting from the addition of appropriate portions of Sr, which supports high electron conductivity and rapid ion/electron transport within the electrode and at the electrode/electrolyte interface. All the results show that the SBOs have considerable potential for use as high-performance battery-type electrodes in supercapacitors.

scholarly journals Facile Fabrication of MnCo2O4/NiO Flower-Like Nanostructure Composites with Improved Energy Storage Capacity for High-Performance Supercapacitors

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1424
Author(s):  
Sangaraju Sambasivam ◽  
K. V. G. Raghavendra ◽  
Anil Kumar Yedluri ◽  
Hammad Mueen Arbi ◽  
Venkatesha Narayanaswamy ◽  
...  
Keyword(s):  
Energy Storage ◽  
Photoelectron Spectroscopy ◽  
Active Sites ◽  
High Performance ◽  
Storage System ◽  
Specific Capacity ◽  
Energy Storage System ◽  
Diffraction Field ◽  
X Ray ◽  
Binder Free

Over the past few decades, the application of new novel materials in energy storage system has seen excellent development. We report a novel MnCo2O4/NiO nanostructure prepared by a simplistic chemical bath deposition method and employed it as a binder free electrode in the supercapacitor. The synergistic attraction from a high density of active sites, better transportation of ion diffusion and super-most electrical transportation, which deliver boost electrochemical activities. X-ray diffraction, field-emission scanning electron microscopy, and X-ray photoelectron spectroscopy have been used to investigate the crystallinity, morphology, and elemental composition of the as-synthesized precursors, respectively. Cyclic voltammetry, galvanostatic charge/discharge, and electron impedance spectroscopy have been employed to investigate the electrochemical properties. The unique nanoparticle structures delivered additional well-organized pathways for the swift mobility of electrons and ions. The as-prepared binder-free MnCo2O4/NiO nanocomposite electrode has a high specific capacity of 453.3 C g−1 at 1 Ag−1, and an excellent cycling reliability of 91.89 percent even after 4000 cycles, which are significantly higher than bare MnCo2O4 and NiO electrodes. Finally, these results disclose that the as-fabricated MnCo2O4/NiO electrode could be a favored-like electrode material holds substantial potential and supreme option for efficient supercapacitor and their energy storage-related applications.

scholarly journals Cobalt Oxide Nanograins and Silver Nanoparticles Decorated Fibrous Polyaniline Nanocomposite as Battery-Type Electrode for High Performance Supercapattery

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2816
Author(s):  
Javed Iqbal ◽  
Arshid Numan ◽  
Mohammad Omaish Ansari ◽  
Rashida Jafer ◽  
Priyanka R. Jagadish ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cobalt Oxide ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Oxidative Polymerization ◽  
Specific Capacity ◽  
Cyclic Stability ◽  
Structural Studies ◽  
X Ray ◽  
Ternary Nanocomposite

In this study, silver (Ag) and cobalt oxide (Co3O4) decorated polyaniline (PANI) fibers were prepared by the combination of in-situ aniline oxidative polymerization and the hydrothermal methodology. The morphology of the prepared Ag/Co3O4@PANI ternary nanocomposite was studied by scanning electron microscopy and transmission electron microscopy, while the structural studies were carried out by X-ray diffraction and X-ray photoelectron spectroscopy. The morphological characterization revealed fibrous shaped PANI, coated with Ag and Co3O4 nanograins, while the structural studies revealed high purity, good crystallinity, and slight interactions among the constituents of the Ag/Co3O4@PANI ternary nanocomposite. The electrochemical performance studies revealed the enhanced performance of the Ag/Co3O4@PANI nanocomposite due to the synergistic/additional effect of Ag, Co3O4 and PANI compared to pure PANI and Co3O4@PANI. The addition of the Ag and Co3O4 provided an extended site for faradaic reactions leading to the high specific capacity. The Ag/Co3O4@PANI ternary nanocomposite exhibited an excellent specific capacity of 262.62 C g−1 at a scan rate of 3 mV s−1. The maximum energy and power density were found to be 14.01 Wh kg−1 and 165.00 W kg−1, respectively. The cyclic stability of supercapattery (Ag/Co3O4@PANI//activated carbon) consisting of a battery type electrode demonstrated a gradual increase in specific capacity with a continuous charge–discharge cycle until ~1000 cycles, then remained stable until 2500 cycles and later started decreasing, thereby showing the cyclic stability of 121.03% of its initial value after 3500 cycles.

Hydrothermal Synthesis of Cobalt Ruthenium Sulfides as Promising Pseudocapacitor Electrode Materials

Coatings ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 200 ◽  
Author(s):  
Ravi Bolagam ◽  
Sukkee Um
Keyword(s):  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Electrode Materials ◽  
Electrochemical Impedance ◽  
Rate Capability ◽  
Metal Sulfide ◽  
Energy Storage Devices ◽  
X Ray ◽  
Storage Devices ◽  
Ternary Metal

In this paper, we report the successful synthesis of cobalt ruthenium sulfides by a facile hydrothermal method. The structural aspects of the as-prepared cobalt ruthenium sulfides were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy. All the prepared materials exhibited nanocrystal morphology. The electrochemical performance of the ternary metal sulfides was investigated by cyclic voltammetry (CV), galvanostatic charge-discharge (GCD), and electrochemical impedance spectroscopy techniques. Noticeably, the optimized ternary metal sulfide electrode exhibited good specific capacitances of 95 F g−1 at 5 mV s−1 and 75 F g−1 at 1 A g−1, excellent rate capability (48 F g−1 at 5 A g−1), and superior cycling stability (81% capacitance retention after 1000 cycles). Moreover, this electrode demonstrated energy densities of 10.5 and 6.7 Wh kg−1 at power densities of 600 and 3001.5 W kg−1, respectively. These attractive properties endow proposed electrodes with significant potential for high-performance energy storage devices.

scholarly journals Novel Carbon Dots Derived from Glycyrrhizae Radix et Rhizoma and Their Anti-Gastric Ulcer Effect

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1512
Author(s):  
Yuhan Liu ◽  
Meiling Zhang ◽  
Jinjun Cheng ◽  
Yue Zhang ◽  
Hui Kong ◽  
...  
Keyword(s):  
Gastric Ulcer ◽  
Photoelectron Spectroscopy ◽  
Carbon Dots ◽  
High Performance ◽  
Raw264.7 Cells ◽  
Mice Model ◽  
X Ray ◽  
Glycyrrhizae Radix ◽  
Transmission Electron ◽  
High Resolution Tem

Glycyrrhizae Radix et Rhizoma (GRR) is one of the commonly used traditional Chinese medicines in clinical practice, which has been applied to treat digestive system diseases for hundreds of years. GRR is preferred for anti-gastric ulcer, however, the main active compounds are still unknown. In this study, GRR was used as precursor to synthesize carbon dots (CDs) by a environment-friendly one-step pyrolysis process. GRR-CDs were characterized by using transmission electron microscopy, high-resolution TEM, fourier transform infrared, ultraviolet-visible and fluorescence spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and high-performance liquid chromatography. In addition, cellular toxicity of GRR-CDs was studied by using CCK-8 in RAW264.7 cells, and the anti-gastric ulcer activity was evaluated and confirmed using mice model of acute alcoholic gastric ulcer. The experiment confirmed that GRR-CDs were the spherical structure with a large number of active groups on the surface and their particle size ranged from 2 to 10 nm. GRR-CDs had no toxicity to RAW264.7 cells at concentration of 19.5 to 5000 μg/mL and could reduce the oxidative damage of gastric mucosa and tissues caused by alcohol, as demonstrated by restoring expression of malondialdehyde, superoxide dismutase and nitric oxide in serum and tissue of mice. The results indicated the explicit anti-ulcer activity of GRR-CDs, which provided a new insights for the research on effective material basis of GRR.

Use of anti-solvent to enhance thermoelectric response of hybrid-halide perovskite thin films

2022 ◽  
Author(s):  
Shrikant SAINI ◽  
Izuki Matsumoto ◽  
Sakura Kishishita ◽  
Ajay Kumar Baranwal ◽  
Tomohide Yabuki ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Cost Effective ◽  
Performance Tuning ◽  
Charge Carrier Density ◽  
X Ray ◽  
Thermoelectric Energy Harvesting ◽  
Halide Perovskite

Abstract Hybrid halide perovskite has been recently focused on thermoelectric energy harvesting due to the cost-effective fabrication approach and ultra-low thermal conductivity. To achieve high performance, tuning of electrical conductivity is a key parameter that is influenced by grain boundary scattering and charge carrier density. The fabrication process allows tuning these parameters. We report the use of anti-solvent to enhance the thermoelectric performance of lead-free hybrid halide perovskite, CH3NH3SnI3, thin films. Thin films with anti-solvent show higher connectivity in grains and higher Sn+4 oxidation states which results in enhancing the value of electrical conductivity. Thin films were prepared by a cost-effective wet process. Structural and chemical characterizations were performed using x-ray diffraction, scanning electron microscope, and x-ray photoelectron spectroscopy. The value of electrical conductivity and the Seebeck coefficient were measured near room temperature. The high value of power factor (1.55 µW/m.K2 at 320 K) was achieved for thin films treated with anti-solvent.

scholarly journals Ce-Doped PANI/Fe3O4 Nanocomposites: Electrode Materials for Supercapattery

2021 ◽  
Vol 3 ◽  
Author(s):  
Subash Pandey ◽  
Shova Neupane ◽  
Dipak Kumar Gupta ◽  
Anju Kumari Das ◽  
Nabin Karki ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Electrode Material ◽  
High Performance ◽  
Electrode Materials ◽  
Specific Capacity ◽  
Maximum Energy ◽  
Potential Range ◽  
X Ray Diffraction ◽  
Active Electrode ◽  
Transmission Electron

In this study, we report on a combined approach to preparing an active electrode material for supercapattery application by making nanocomposites of Polyaniline/Cerium (PANI/Ce) with different weight percentages of magnetite (Fe3O4). Fourier-transform infrared spectroscopy (FTIR) and x-ray diffraction (XRD) analyses supported the interaction of PANI with Ce and the formation of the successful nanocomposite with magnetite nanoparticles. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses showed the uniform and porous morphology of the composites. Cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) were used to test the supercapattery behavior of the nanocomposite electrodes in 1.0 M H2SO4. It was found that the supercapattery electrode of PANI/Ce+7 wt.% Fe3O4 exhibited a specific capacity of 171 mAhg−1 in the potential range of −0.2 to 1.0 V at the current density of 2.5 Ag−1. Moreover, PANI/Ce+7 wt.% Fe3O4 revealed a power density of 376.6 Wkg−1 along with a maximum energy density of 25.4 Whkg−1 at 2.5 Ag−1. Further, the cyclic stability of PANI/Ce+7 wt.% Fe3O4 was found to be 96.0% after 5,000 cycles. The obtained results suggested that the PANI/Ce+Fe3O4 nanocomposite could be a promising electrode material candidate for high-performance supercapattery applications.

scholarly journals Towards chemically neutral carbon cleaning processes: plasma cleaning of Ni, Rh and Al reflective optical coatings and thin Al filters for free-electron lasers and synchrotron beamline applications

2018 ◽  
Vol 25 (6) ◽  
pp. 1642-1649 ◽  
Author(s):  
Harol Moreno Fernández ◽  
Marco Zangrando ◽  
Guillaume Sauthier ◽  
Alejandro R. Goñi ◽  
Vincent Carlino ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Free Electron ◽  
Inductively Coupled Plasma ◽  
High Performance ◽  
Extreme Ultraviolet ◽  
Filter Material ◽  
Gas Mixture ◽  
Carbon Contamination ◽  
X Ray ◽  
Chemical Surface

The choice of a reflective optical coating or filter material has to be adapted to the intended field of application. This is mainly determined by the required photon energy range or by the required reflection angle. Among various materials, nickel and rhodium are common materials used as reflective coatings for (soft) X-ray mirrors. Similarly, aluminium is one of the most commonly used materials for extreme ultraviolet and soft X-ray transmission filters. However, both of these types of optics are subject to carbon contamination, which can be increasingly problematic for the operation of the high-performance free-electron laser and synchrotron beamlines. As an attempt to remove this type of contamination, an inductively coupled plasma source has been used in conjunction with N2/O2/H2 and N2/H2 feedstock gas plasmas. Results from the chemical surface analysis of the above materials before and after plasma treatment using X-ray photoelectron spectroscopy are reported. It is concluded that a favorable combination of an N2/H2 plasma feedstock gas mixture leads to the best chemical surface preservation of Ni, Rh and Al while removing the carbon contamination. However, this feedstock gas mixture does not remove C contamination as rapidly as, for example, an N2/O2/H2 plasma which induces the surface formation of NiO and NiOOH in Ni and RhOOH in Rh foils. As an applied case, the successful carbon removal from ultrathin Al filters previously used at the FERMI FEL1 using an N2/H2 plasma is demonstrated.

High-Capacity Derivatives Produced from Hydrolytic Lignin as Electrode Materials for Energy Storage and Conversion

2018 ◽  
Vol 386 ◽  
pp. 359-364
Author(s):  
Yury M. Nikolenko ◽  
Denis P. Opra ◽  
Alexander K. Tsvetnikov ◽  
Alexander Yu. Ustinov ◽  
Valery G. Kuryavyi ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Energy Storage ◽  
Electrode Materials ◽  
Electronic Conductivity ◽  
Specific Capacity ◽  
Energy Storage And Conversion ◽  
Operating Voltage ◽  
X Ray ◽  
Thermally Activated ◽  
Hydrolytic Lignin

The hydrolytic lignin derivatives have been prepared via its physical activation (high-temperature heating in vacuum) followed by chemical modification (fluorination). The obtained products were characterized using scanning electron microscopy, X-ray diffraction, transmission electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. It was found that the graphitized product of thermal activation up to 1000 °C at a low rate of < 2 °C/min under high vacuum shows an enhanced specific surface area (215 m2/g), that makes its potentially useful as sorbent, catalytic substrate or electrode material. To clarify the potentialities of hydrolytic lignin derivatives for energy storage and conversion, the electrochemical system with metallic lithium anode was applied. The galvanostatic discharge of battery at a current density of 100 μA/cm2between 3.0 and 0.5 V shows that the specific capacity of thermally activated derivative is equal to 845 mA·h/g, while the untreated lignin yields only 190 mA·h/g. The improve of the electrochemical performance of product originates from its graphitization, increasing electronic conductivity, and, possibly, enhanced ability to adsorb of oxygen. The fluorination of both the lignin and its thermally activated form results in higher operating voltage of battery, as seems, due to the involvement of fluorine bound to carbon in electrochemical process.

Porous Activity of Biomass-Activated Carbon Enhanced by Nitrogen-Dopant Towards High-Performance Lithium Ion Hybrid Battery-Supercapacitor

2021 ◽  
Author(s):  
Juan Yu ◽  
Xuyang Wang ◽  
Jiaxin Peng ◽  
Xuefeng Jia ◽  
Linbo Li ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Energy Storage ◽  
Pore Structure ◽  
High Performance ◽  
Electrode Materials ◽  
Specific Capacity ◽  
Lithium Ion ◽  
Utilization Efficiency ◽  
Energy Storage Devices ◽  
Storage Devices

Abstract Biomass-activated carbon materials are promising electrode materials for lithium-ion hybrid capacitors (LiCs) because of their natural hierarchical pore structure. The efficient utilization of structural pores in activated carbon is very important for their electrochemical performance. Herein, porous biomass-activated carbon (PAC) with large specific surface area was prepared using a one-step activation method with biomass waste as the carbon source and ZnCl2 as the activator. To further improve its pore structure utilization efficiency, the PAC was doped with nitrogen using urea as the nitrogen source. The experimental results confirmed that PAC-1 with a high nitrogen doping level of 4.66% exhibited the most efficient pore utilization among all the samples investigated in this study. PAC-1 exhibited 92% capacity retention after 8000 cycles, showing good cycling stability. Then, to maximize the utilization of high-efficiency energy storage devices, LiNi0.8Co0.15Al0.05O2 (NCA), a promising cathode material for lithium-ion batteries with high specific capacity, was compounded with PAC-1 in different ratios to obtain NCA@PC composites. The NCA@PC-9 composite exhibited excellent capacitance in LiCs and an energy density of 210.9 Wh kg-1 at a high power density of 13.3 kW kg-1. These results provide guidelines for the design of high-performance and low-cost energy storage devices.

Sign in / Sign up

Export Citation Format

Share Document