scholarly journals Experimental Investigation of the Ground Effect of WIG Craft—NEW1 Model

Proceedings ◽  
2020 ◽  
Vol 39 (1) ◽  
pp. 17
Author(s):  
Sakornsin ◽  
Thipyopas ◽  
Atipan
Keyword(s):  
Lift Coefficient ◽  
Ground Surface ◽  
Ground Effect ◽  
Aerodynamic Characteristics ◽  
Scale Model ◽  
Negative Slope ◽  
Stream Velocity ◽  
Longitudinal Stability ◽  
Moment Coefficient ◽  
The Moment

Navy Experimental Wing-in-Ground-Effect (WIG) craft namely as NEW1, is the first version of 2-seated WIG craft which has been designed and developed by Royal Thai Navy since 2017. This experimental research is a part of the NEW1 project which aims to investigate the aerodynamic characteristics and aspects of the flow passing through the WIG craft model when in ground effect. In the experiment, the WIG craft—NEW1 of 1:15 scale model is tested in a close circuit wind tunnel of 1 m × 1 m test section at Kasetsart University. The tests are conducted at the free stream velocity of 40 m/s or Reynolds number of 280,000, at angles of attack ranging from −9° to 21°, and at the wing to ground distances ranging from 5.0 C to 0.3 C. The measurement of 6-DoF of forces and moments and pressure distributions on the ground surface underneath the WIG craft model are made during the tests. The results show that the ground has significant effects on the aerodynamic characteristics of the WIG craft model when the wing to ground distance is less than its mean chord. It was found that when the model move from 5.0 C (out of ground effect) to 0.3 C, the lift coefficient increases up to 15.7%, the drag coefficient decreases up to 5.6%, and the lift to drag ratio increases 33.4%. The proximity of the model to the ground also affects the longitudinal stability of the model. The moment coefficient curves against angle of attack has negative slope for both in and out of ground effect indicating favorable longitudinal stability. However, it was found that the aerodynamic center move further aft toward the trailing edge when the model move closer to the ground.

The Effect of Canard to the Aerodynamic Behavior of Blended Wing Body Aircraft

2012 ◽  
Vol 225 ◽  
pp. 38-42
Author(s):  
Zurriati Mohd Ali ◽  
Wahyu Kuntjoro ◽  
Wisnoe Wirachman
Keyword(s):  
Mach Number ◽  
Wind Tunnel ◽  
Aerodynamic Characteristic ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Moment Coefficient ◽  
Subsonic Wind Tunnel ◽  
Setting Angle ◽  
Blended Wing Body ◽  
The Moment

This paper presents a study on the effect of canard setting angle on the aerodynamic characteristic of a Blended Wing Body (BWB). Canard effects to BWB aerodynamic characteristics are not widely investigated. Hence the focus of the study is to investigate the variations of lifts, drags and moments when the angles of attack are varied at different canard setting angles. Wind tunnel tests were performed on BWB aircraft with canard setting angles,  ranging from -20˚ to 20˚. Angles of attack,  were varied from -10˚ to 10˚. Aspect ratio and canard planform area were kept fixed. All tests were conducted in the subsonic wind tunnel at Universiti Teknologi MARA, at Mach number of 0.1. The streamlines flow, at the upper surface of the canard was visualized using mini tuft. Result shows that the lift coefficient does not change much with different canard setting angles. As expected, the lift coefficient increases with increasing angles of attack at any canard setting angle. In general, the moment coefficient increases as the canard setting angle is increased. The results obtained in this research will be of importance to the understanding of aerodynamic behavior of BWB employing canard in its configuration.

Aerodynamic Characteristics Prediction via Artificial Hair Sensor and Feedforward Neural Network

2015 ◽  
Author(s):  
Kaman Thapa Magar ◽  
Gregory W. Reich ◽  
Matthew R. Rickey ◽  
Brian M. Smyers ◽  
Richard V. Beblo
Keyword(s):  
Neural Network ◽  
Lift Coefficient ◽  
Unsteady Aerodynamics ◽  
Aerodynamic Characteristics ◽  
Stream Velocity ◽  
Sensors And Actuators ◽  
Local Flow ◽  
Distributed Sensors ◽  
Moment Coefficient ◽  
Hair Sensors

Fly by feel is a concept in which distributed sensors and actuators are integrated on an aerial system for state awareness or sensation of the environment, and make use of distributed control to increase the system maneuverability, stability and safety. Artificial hair sensors are good candidates as sensors for the fly by feel concept because they are lightweight, have low manufacturing costs and can easily be integrated on the surface of air-vehicle without affecting the flow. We investigate an application of artificial hair sensors considering its capability of measuring the local flow velocity combined with a Feedforward Artificial Neural Network to predict the aerodynamic quantities such as lift coefficient, moment coefficient, angle of attack and free-stream velocity in real-time. These quantities, when combined with the physical and unsteady aerodynamics parameters, will make a framework for designing and implementing an active controller for gust alleviation in a pitch and plunge airfoil system.

Wind-tunnel tests of a tilt-rotor aircraft

2011 ◽  
Vol 115 (1167) ◽  
pp. 315-322 ◽  
Author(s):  
G. Gibertini ◽  
F. Auteri ◽  
G. Campanardi ◽  
C. Macchi ◽  
A. Zanotti ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Aircraft Design ◽  
Longitudinal Axis ◽  
Scale Model ◽  
Nonlinear Behaviour ◽  
Moment Coefficient ◽  
High Incidence ◽  
Aerodynamic Test ◽  
The Moment ◽  
Very High

Abstract A wide aerodynamic test campaign has been carried out on the tiltrotor aircraft ERICA at the Large Wind Tunnel of Politecnico di Milano by means of a modular 1:8 scale model in order to produce a dataset necessary to better understand the aerodynamic behaviour of the aircraft and to state its definitive design. The target of the tests was the measurement of the aerodynamic forces and moments in several different configurations and different attitudes. The test program included some conditions at very high incidence and sideslip angles that typically belong to the helicopter-mode flight envelope and measurements of forces on the tail and on the tilting wings. A large amount of data has been collected that will be very useful to refine the aircraft design. In general the aircraft aerodynamics do not present any critical problems, but further optimisation is still possible. From the viewpoint of drag in the cruise configuration, the sponsons of the landing gear seem to be worth some further design refinement since they are responsible for a 20% drag increase with respect to the pure fuselage configuration. On the contrary, the wing fairing has proved to work well when the aircraft longitudinal axis is aligned with the wind, providing just a slight drag increase. Two other interesting aspects are the quite nonlinear behaviour of the side force for the intermediate sideslip angles as well as the noticeable hysteresis in the moment coefficient at very high incidence angles.

Experimental Aerodynamic Characteristics of a Compound Wing in Ground Effect

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun Abdul Malek ◽  
Shuhaimi Mansor ◽  
Nor Azwadi Che Sidik ◽  
Agoes Priyanto
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Center Of Pressure ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Ground Clearance

Wing configuration is a parameter that affects the performance of wing-in-ground effect (WIG) craft. In this study, the aerodynamic characteristics of a new compound wing were investigated during ground effect. The compound wing was divided into three parts with a rectangular wing in the middle and two reverse taper wings with anhedral angle at the sides. The sectional profile of the wing model is NACA6409. The experiments on the compound wing and the rectangular wing were carried to examine different ground clearances, angles of attack, and Reynolds numbers. The aerodynamic coefficients of the compound wing were compared with those of the rectangular wing, which had an acceptable increase in its lift coefficient at small ground clearances, and its drag coefficient decreased compared to rectangular wing at a wide range of ground clearances, angles of attack, and Reynolds numbers. Furthermore, the lift to drag ratio of the compound wing improved considerably at small ground clearances. However, this improvement decreased at higher ground clearance. The drag polar of the compound wing showed the increment of lift coefficient versus drag coefficient was higher especially at small ground clearances. The Reynolds number had a gradual effect on lift and drag coefficients and also lift to drag of both wings. Generally, the nose down pitching moment of the compound wing was found smaller, but it was greater at high angle of attack and Reynolds number for all ground clearance. The center of pressure was closer to the leading edge of the wing in contrast to the rectangular wing. However, the center of pressure of the compound wing was later to the leading edge at high ground clearance, angle of attack, and Reynolds number.

scholarly journals Analytic determination of tandem-scheme aircraft aerodynamic characteristics

2015 ◽  
pp. 59-71
Author(s):  
Ілля Станіславович Кривохатько ◽  
Віталій Вікторович Сухов
Keyword(s):  
Mathematical Model ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Design ◽  
New Approach ◽  
Definite Integrals ◽  
Moment Coefficient ◽  
Numerical Computing ◽  
Theoretical Results

In present article analytic method of downwash after wing, lift coefficient and pitching moment coefficient determination for tandem-scheme aircraft was upgraded. Mathematical model is based on Bio-Savart formula and avoid approximate calculus of indefinite integrals in contrast to classical theory. Instead of it new approach consists on numerical computing of definite integrals with high accuracy (error less than 10­-5 was achieved). Method is appropriate for low Mach number and for any Reynolds number. Theoretical results calculated according to proposed method were compared with wind tunnel experiment data and showed good agreement.Developed mathematical model allows optimization of tandem-scheme aircraft aerodynamic design with different objective function. In the next works method will be expanded on the lateral aerodynamic characteristics.

Three-Dimensional Wing Design Towards the Future Mars Airplane

2011 ◽  
Author(s):  
Ryoji Kojima ◽  
Donghi Lee ◽  
Tomoaki Tatsukawa ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Viscous Drag ◽  
Stream Velocity ◽  
Main Stream ◽  
Lower Reynolds Number

The effects of aspect ratio and Reynolds number on aerodynamic characteristics of three-dimensional rectangular wing at low Reynolds number of 103 to 105, are investigated with Reynolds-averaged Navier-Stokes solver with the Baldwin-Lomax model. Present results show that lift coefficient decreases drastically at lower aspect ratio than 4. Besides, the much larger viscous drag coefficient is obtained at the lower Reynolds number, especially lower than 104. In order to focus on designing practical wings, the particular cases under the condition of fixed wing-surface area and fixed main stream velocity are conducted. The results show that there is trade-off between the decrease in viscous drag coefficient with increasing Reynolds number and the increase in lift coefficient with increasing aspect ratio. At the lower Reynolds number condition, as the former effect is stronger than the latter one, maximum lift-to-drag ratio is obtained at lower aspect ratio.

Investigation on Propeller Slipstream by Using an Unstructured Rans Solver Based on Overlapping Grids

2017 ◽  
Vol 34 (2) ◽  
pp. 89-101 ◽  
Author(s):  
X. Q. Gong ◽  
M. S. Ma ◽  
J. Zhang ◽  
J. Tang
Keyword(s):  
Pressure Distribution ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Linear Interpolation ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Overlapping Grids ◽  
Moment Coefficient ◽  
Grid Technique

AbstractBased on unstructured hybrid grid and dynamic overlapping grid technique, numerical simulations of Unsteady Reynolds Averaged Navier-Stokes equations were performed and investigation on isolated propeller aerodynamic characteristics and effects of propeller slipstream on turboprops were undertaken. The computational grid consisted of rotational subzone of propeller and stationary major-zone of aircraft, and walls criterion was used in the automatic hole-cutting procedure. Distance weight interpolation and tri-linear interpolation were developed to transfer information between the rotational and stationary subzones. The boundaries of overlapping grids were optimized for fixed axis rotation. The governing equations were solved by dual-time method and Lower Upper-Symmetric Gauss-Seidel method. The method and grid technique were verified by isolated propeller configuration and the computational results were in well agreement with the experimental data. The grid independence was studied to establish the numerical results. Finally, the flow around a turboprop case was simulated and the influence of propeller slipstream was presented by analyzing the surface pressure contours, profile pressure distribution, vorticity contours and profile streamline. It's indicated that the slipstream accelerates and rotates the free stream flow, changing the local angle of attack, enhancing the downwash effects, affecting the pressure distribution on wing and horizontal tail, as well as increasing the drag coefficient, pitching moment coefficient and the slope of lift coefficient.

scholarly journals Wind Tunnel Tests on Aerodynamic Characteristics of Ice-Coated 4-Bundled Conductors

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Li Xin-min ◽  
Nie Xiao-chun ◽  
Zhu Yong-kun ◽  
You Yi ◽  
Yan Zhi-tao
Keyword(s):  
Wind Tunnel ◽  
Great Influence ◽  
Aerodynamic Characteristics ◽  
Coated Conductors ◽  
Ice Thickness ◽  
Ice Accretion ◽  
Aerodynamic Coefficients ◽  
Wind Tunnel Tests ◽  
Moment Coefficient ◽  
The Moment

Wind tunnel tests were carried out to obtain the static aerodynamic characteristics of crescent iced 4-bundled conductors with different ice thicknesses, initial ice accretion angles, bundle spaces, and wind attack angles. The test models were made of the actual conductors and have a real rough surface. Test results show that the influence of wake interference on the drag coefficients of leeward subconductors is obvious. The interference angle range is larger than 20° and the drag coefficient curves of leeward subconductors have a sudden decrease phenomenon at some certain wind attack angles. The absolute value of the lift and moment coefficient increases with the increase of the ice thickness. In addition, the galloping of the iced subconductor may occur at the angle of wind attack near ±20° and the wake increases the moment coefficient. The variation of initial ice accretion angle has a significant influence on the aerodynamic coefficients. The aerodynamic coefficient curves exhibit a “moving” phenomenon at different initial ice accretion angles. The bundle spaces have a great influence on the moment coefficient of leeward thin ice-coated conductors. With the increase of ice thickness, the bundle spaces generally have little influence on the aerodynamic coefficients.

Experimental investigation of the aerodynamic characteristics of generic fan-in-wing configurations

2009 ◽  
Vol 113 (1139) ◽  
pp. 9-20 ◽  
Author(s):  
N. Thouault ◽  
C. Breitsamter ◽  
N. A. Adams ◽  
C. Gologan ◽  
J. Seifert
Keyword(s):  
Experimental Investigation ◽  
Lift Coefficient ◽  
Ground Effect ◽  
Aerodynamic Characteristics ◽  
Flow Visualisation ◽  
Force Measurements ◽  
Tunnel Model ◽  
Image Velocimetry ◽  
Flow Circulation ◽  
Stereo Particle Image Velocimetry

Abstract This experimental investigation concentrates on the aerodynamic behaviour of a generic fan-in-wing configuration. The effects of the fan(s) on the flow circulation in a short take-off and landing or a transition flight condition without ground effect are evaluated. A wind-tunnel model has been constructed and tested to quantify the aerodynamic effects. Force measurements, surface pressure measurements, stereo-particle image velocimetry and wool tufts flow visualisation are performed. Different fan-in-wing configurations with the fans rotating in the wing plane, one fan either at the rear or front part of the wing and two fans are compared to the closed wing without fans set as reference. A fan placed near the trailing edge improves significantly the lift coefficient due to a jet flap effect on the wing lower side combined with enhanced suction on the wing upper side. The jet exiting the nozzle rolls up in a counter rotating pair of vortices affecting significantly the wing behaviour. This experimental investigation constitutes also a useful database for further CFD comparison.

Experimental Investigation of the Aerodynamics and Flowfield of a NACA 0015 Airfoil Over a Wavy Ground

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
T. Lee ◽  
V. Tremblay-Dionne
Keyword(s):  
Lift Coefficient ◽  
Ground Effect ◽  
Lower Surface ◽  
Moment Coefficient ◽  
Aerodynamic Properties ◽  
Image Velocimetry ◽  
Ground Distance ◽  
Almost All ◽  
Naca 0015 ◽  
The Impact

The aerodynamic properties and flowfield of a NACA 0015 airfoil over a wavy ground were investigated experimentally via surface pressure and particle image velocimetry (PIV) measurements. Flat-surface results were also obtained to be served as a comparison. For the wavy ground, there exhibited a cyclic variation in the sectional lift coefficient Cl over an entire wavelength. The maximum Cl observed at the wave peak (produced by the wavy ground-induced RAM pressure) and minimum Cl occurred at the wave valley (resulting from the unusual suction pressure developed on the airfoil's lower surface due to the converging-diverging flow passage developed underneath it) reduced with increasing ground distance. By contrast, the pitching-moment coefficient showed an opposite trend to the variation in Cl and had an almost all-negative value. Meanwhile, two peak values in the drag coefficient over each wavelength were observed. The wavy ground effect-produced gains in the mean Cl and lift-to-drag ratio were at the expense of longitudinal stability. Additional measurements considering different wavelengths and amplitudes are needed to further quantify the impact of wavy ground on wing-in-ground effect (WIG) airfoils and wings.

Sign in / Sign up

Export Citation Format

Share Document