scholarly journals Random Fiber Grating Characterization Based on OFDR and Transfer Matrix Method

Sensors ◽  
2020 ◽  
Vol 20 (21) ◽  
pp. 6071
Author(s):  
Zichao Zhou ◽  
Chen Chen ◽  
Ping Lu ◽  
Stephen Mihailov ◽  
Liang Chen ◽  
...  
Keyword(s):  
Fiber Lasers ◽  
Spectral Response ◽  
Quantitative Relationship ◽  
Spatial Domain ◽  
Experimental Results ◽  
Period Variation ◽  
Peak Wavelength ◽  
Variation Range ◽  
Wavelength Variation ◽  
Simulation Results

Random fiber gratings (RFGs) have shown great potential applications in fiber sensing and random fiber lasers. However, a quantitative relationship between the degree of randomness of the RFG and its spectral response has never been analyzed. In this paper, two RFGs with different degrees of randomness are first characterized experimentally by optical frequency domain reflectometry (OFDR). Experimental results show that the high degree of randomness leads to low backscattering strength of the grating and strong strength fluctuations in the spatial domain. The local spectral response of the grating exhibits multiple peaks and a large peak wavelength variation range when its degree of randomness is high. The linewidth of its fine spectrum structures shows scaling behavior with the grating length. In order to find a quantitative relationship between the degree of randomness and spectrum property of RFG, entropy was introduced to describe the degree of randomness induced by period variation of the sub-grating. Simulation results showed that the average reflectivity of the RFG in dB scale decreased linearly with increased sub-grating entropy, when the measured wavelength range was smaller than the peak wavelength variation range of the sub-grating. The peak reflectivity of the RFG was determined by κ2LΔP (where κ is the coupling coefficient, L is the grating length, ΔP is period variation range of the sub-grating) rather than κL when ΔP is larger than 8 nm in the spatial domain. The experimental results agree well with the simulation results, which helps to optimize the RFG manufacturing processes for future applications in random fiber lasers and sensors.

Simulation of carding condensing process

2021 ◽  
pp. 004051752098812
Author(s):  
Xixi Qian ◽  
Yuanying Shen ◽  
Qiaoli Cao ◽  
Jun Ruan ◽  
Chongwen Yu
Keyword(s):  
Experimental Results ◽  
Simulation Results ◽  
Carding Machine ◽  
The Web

A simulation describing the fiber movement during the condensation was conducted, and the effect of the condensation in the carding machine was studied. The simulation results showed that the condensation has the blending and the evening effect on the condensed sliver, which can be explained by the fiber rearrangement. Moreover, the increasing web width and the decreasing condensing length can result in a more uniform sliver. Further, the evening effect of the web width on the web was verified by experiments. The simulation results were in general agreement with the experimental results.

The Effect of Different Turbulence Models on the Emitter Discharge by Using Computational Fluid Dynamics

2013 ◽  
Vol 662 ◽  
pp. 586-590
Author(s):  
Gang Lu ◽  
Qing Song Yan ◽  
Bai Ping Lu ◽  
Shuai Xu ◽  
Kang Li
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Turbulence Models ◽  
Experimental Results ◽  
Turbulent Model ◽  
Simulation Results ◽  
Rsm Model ◽  
Dynamics Method ◽  
Emitter Discharge

Four types of Super Typhoon drip emitter with trapezoidal channel were selected out for the investigation of the flow field of the channel, and the CFD (Computational Fluid Dynamics) method was applied to simulate the micro-field inside the channel. The simulation results showed that the emitter discharge of different turbulent model is 4%-14% bigger than that of the experimental results, the average discharge deviation of κ-ω and RSM model is 5, 4.5 respectively, but the solving efficiency of the κ-ω model is obviously higher than that of the RSM model.

Design of Magnetic Levitated Thrust Bearing Experiment Table

2011 ◽  
Vol 199-200 ◽  
pp. 597-602
Author(s):  
Shou Fa Liu ◽  
Zhang Jie Shi ◽  
Chun Feng Li
Keyword(s):  
Thrust Bearing ◽  
Deformation Measurement ◽  
Experimental Results ◽  
Electromagnetic Parameters ◽  
Ansys Simulation ◽  
Overall Design ◽  
Experimental Parameters ◽  
Structural Dimensions ◽  
Simulation Results

In this paper, the overall design of magnetic levitated thrust bearing experiment table was completed, of which the main experimental parameters those are electromagnetic parameters and structural dimensions were determined, in addition, the joint debugging and deformation measurement are performed. Analysis results showed that theoretical value, ANSYS simulation results and experimental results were similar, which said that it is feasible to perform stiffness check of the thrust collar on the experiment table.

scholarly journals Numerical Simulations of V-Shaped Plates Subjected to Blast Loadings: A Validation Study

2016 ◽  
Vol 10 (11) ◽  
pp. 203
Author(s):  
Mohd Zaid Othman ◽  
Qasim H. Shah ◽  
Muhammad Akram Muhammad Khan ◽  
Tan Kean Sheng ◽  
M. A. Yahaya ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Variable Mass ◽  
Blast Loading ◽  
Experimental Results ◽  
Average Difference ◽  
Simulation Results ◽  
Blast Loadings ◽  
Carrier Vehicle ◽  
Good Agreement

A series of numerical simulations utilizing LS-DYNA was performed to determine the mid-point deformations of V-shaped plates due to blast loading. The numerical simulation results were then compared with experimental results from published literature. The V-shaped plate is made of DOMEX 700 and is used underneath an armour personal carrier vehicle as an anti-tank mine to mitigate the effects of explosion from landmines in a battlefield. The performed numerical simulations of blast loading of V-shaped plates consisted of various angles i.e. 60°, 90°, 120°, 150° and 180°; variable mass of explosives located at the central mid-point of the V-shaped vertex with various stand-off distances. It could be seen that the numerical simulations produced good agreement with the experimental results where the average difference was about 26.6%.

Random-Access Multilevel Storage in Phase Change Memory by Staircase-Like Pulse Programming

2011 ◽  
Vol 497 ◽  
pp. 111-115
Author(s):  
Ryota Kobayashi ◽  
Tomoyuki Noguchi ◽  
You Yin ◽  
Sumio Hosaka
Keyword(s):  
Phase Change ◽  
Phase Change Memory ◽  
Random Access ◽  
Experimental Results ◽  
Device Resistance ◽  
Multilevel Storage ◽  
Simulation Results ◽  
Change Memory

We have investigated random-access multilevel storage in phase change memory by staircase-like pulse programming. Staircase-like pulse consists of first sub-pulse and second sub-pulse. Our simulation exhibited that any resistance levels are expected to be randomly accessed by controlling the crystallization with different widths of second sub-pulset2. Based on the simulation results, we did experiment on staircase-like pulse programming. Experimental results showed that the device resistance gradually increased with reducing second sub-pulset2to 0 ns. In other words, random access to any resistance levels was demonstrated to be possible simply by changingt2.

scholarly journals Pneumatic Actuator Controlled by Proportional Valve. Experimental results

2021 ◽  
Vol 286 ◽  
pp. 04010
Author(s):  
Valentin Nicolae Cococi ◽  
Constantin Călinoiu ◽  
Carmen-Anca Safta
Keyword(s):  
Control Valve ◽  
Industrial Applications ◽  
Experimental Results ◽  
Pneumatic Actuator ◽  
Proportional Valve ◽  
Controlled Systems ◽  
Automation Systems ◽  
Simulation Results ◽  
The Mathematical Model ◽  
Fire Ignition

In nowadays the pneumatic controlled systems are widely used in industrial applications where valves must be operated, where there is a fire ignition risk, or in different automation systems where a positioning action is desired. The paper presents the experimental results of a pneumatic actuator controlled by a proportional control valve. The goal of the paper is to compare the experimental results with the numerical simulation results and to improve the mathematical model associated with the experiment.

scholarly journals MEMS-Based Integrated Triaxial Electrochemical Seismometer

Micromachines ◽  
2021 ◽  
Vol 12 (10) ◽  
pp. 1156
Author(s):  
Wenjie Qi ◽  
Bowen Liu ◽  
Tian Liang ◽  
Jian Chen ◽  
Deyong Chen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Ground Motion ◽  
Small Volume ◽  
Three Dimensional ◽  
Experimental Results ◽  
Good Prospect ◽  
High Symmetry ◽  
Noise Levels ◽  
Sensitivity Curves ◽  
Simulation Results

This paper presents a micro-electromechanical systems (MEMS)-based integrated triaxial electrochemical seismometer, which can detect three-dimensional vibration. By integrating three axes, the integrated triaxial electrochemical seismometer is characterized by small volume and high symmetry. The numerical simulation results inferred that the integrated triaxial electrochemical seismometer had excellent independence among three axes. Based on the experimental results, the integrated triaxial electrochemical seismometer had the advantage of small axial crosstalk and could detect vibration in arbitrary directions. Furthermore, compared with the uniaxial electrochemical seismometer, the integrated triaxial electrochemical seismometer had similar sensitivity curves ranging from 0.01 to 100 Hz. In terms of random ground motion response, high consistencies between the developed integrated triaxial electrochemical seismometer and the uniaxial electrochemical seismometer could be easily observed, which indicated that the developed integrated triaxial electrochemical seismometer produced comparable noise levels to those of the uniaxial electrochemical seismometer. These results validated the performance of the integrated triaxial electrochemical seismometer, which has a good prospect in the field of deep geophysical exploration and submarine seismic monitoring.

scholarly journals CFD Study on Impeller Effect on Mixing in Miniature Stirred Tank Reactor

CFD letters ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 15-26
Author(s):  
Adnan Ghulam Mustafa ◽  
Mohd Fadhil Majnis ◽  
Nor Azyati Abdul Muttalib
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Calcium Alginate ◽  
Alginate Beads ◽  
Experimental Results ◽  
Stirred Tank ◽  
Stirred Tank Reactor ◽  
Calcium Alginate Beads ◽  
Tank Reactor ◽  
Simulation Results

Mixing of fluid can happen in existence or absence of impeller which will affect the mixing performance. The hydrodynamics behavior of fluid has a strong effect on the mixing. The design of mixing systems and operation using the agitated tanks is complicated because it is difficult to obtain accurate information for turbulence’s impeller induced. Computational Fluid Dynamics can be used to provide a detailed comprehension of those systems. This paper describes the effect of various designs of impeller in miniature stirred tank reactor towards the mixing of the calcium alginate beads with the milk using Computational Fluid Dynamics (CFD) software, ANSYS Fluent 19.2. The four different type of impellers are edge beater, 5-turbine blade, t-shape, and paddle. The impeller was simulated at different speeds of 150 rpm, 250 rpm, and 300 rpm. K-epsilon turbulence model was employed to simulate the flow distribution pattern of calcium alginate beads and the Multiple Reference Frame approach was used for the impeller rotation’s simulation. The simulation results obtained have a good agreement with the experimental results in term of vortex formation. The simulation results obtained for contour plots were fitted well with the experimental results as well as with pattern of impeller flow which was also studied. As a result, an optimal design of the impeller that is able to produce good mixing can be achieved using CFD analysis. The results obtained after performing the simulation proved that edge beater blade outperformed the other impellers and took the least time to fully distribute the calcium alginate beads in the tank at 250 rpm compared to 150 and 300 rpm. It can also be concluded that the edge beater blade is the best for the mixing of two-phase fluid and also produces mixed pattern flow. The obtained results from CFD can also be used to scale up the mixing process in larger systems.

Effect of Strain Rate on the Simulation of MEMS Safety and Arming Device

2014 ◽  
Vol 609-610 ◽  
pp. 849-855
Author(s):  
Wen Rui Ma ◽  
Guang He
Keyword(s):  
Finite Element Analysis ◽  
Strain Rate ◽  
Impact Load ◽  
Simulation Models ◽  
Strain Rate Effect ◽  
Rate Effect ◽  
Experimental Results ◽  
Analysis Software ◽  
Element Analysis ◽  
Simulation Results

Under launch impact load, LIGA nickel that manufacturing MEMS fuze safety and arming (S&A) device will have obvious strain rate effect. By using finite element analysis software ANSYS/LS-DYNA, simulation models of a small-caliber ammunition MEMS fuze setback S&A device with strain rate effect and without strain rate effect were respectively established. The results of the two simulation modules were quite different. Comparisons between experimental results and simulation results show that simulation results considering strain rate effect agree well with experimental results, which proves strain rate effect should not be ignored in the simulation of MEMS S&A device.

scholarly journals Fractal Image Interpolation: A Tutorial and New Result

2019 ◽  
Vol 3 (1) ◽  
pp. 7
Author(s):  
Chi Kok ◽  
Wing Tam
Keyword(s):  
Image Interpolation ◽  
Spatial Domain ◽  
Fractal Interpolation ◽  
Image System ◽  
Pixel Intensity ◽  
Resolution Image ◽  
Fractal Image ◽  
Pros And Cons ◽  
Simulation Results ◽  
Visual Artifacts

This paper reviews the implementation of fractal based image interpolation, the associated visual artifacts of the interpolated images, and various techniques, including novel contributions, that alleviate these awkward visual artifacts to achieve visually pleasant interpolated image. The fractal interpolation methods considered in this paper are based on the plain Iterative Function System (IFS) in spatial domain without additional transformation, where we believe that the benefits of additional transformation can be added onto the presented study without complication. Simulation results are presented to demonstrate the discussed techniques, together with the pros and cons of each techniques. Finally, a novel spatial domain interleave layer has been proposed to add to the IFS image system for improving the performance of the system from image zooming to interpolation with the preservation of the pixel intensity from the original low resolution image.

Sign in / Sign up

Export Citation Format

Share Document