scholarly journals Influence of Printing Technique and Printing Conditions on Prints Recycling Efficiency and Effluents Quality

2021 ◽  
Vol 14 (1) ◽  
pp. 335
Author(s):  
Marina Vukoje ◽  
Ivana Bolanča Mirković ◽  
Zdenka Bolanča
Keyword(s):  
Oxygen Demand ◽  
Offset Printing ◽  
Experimental Conditions ◽  
Negative Voltage ◽  
Recycled Pulp ◽  
Printing Technique ◽  
Recycled Fibres ◽  
Printing Techniques ◽  
Wastewater Effluents

The aim of this work was to determine the influence of the conventional offset printing technique and digital electrophotography printing with liquid toner (LEP) on some optical properties of recycled fibres. A series of LEP prints was made with the variation of the negative voltage of the developing drum (−200 V, −280 V, −350 V, and −430 V) after calibration of the machine and achieving standard densitometry values. Besides deinkability aspects, the quality of wastewater effluents after process of prints recycling was observed in order to make a conclusion regarding how different printing techniques, conditions in printing process, and different types of inks can affect the wastewater effluents. Results of image analysis showed that by increasing the negative voltage of developing drum in LEP printing technique, the formation of large ink particles on handsheet from recycled pulp increases. Depending on the size of the negative voltage of the developing drum, under the same experimental conditions, handsheets made from LEP recycled fibres have lower whiteness gain, brightness gain, and ΔERIC of handsheets compared to those made from the offset prints. In addition, a certain correlation was found between IEERIC (ink elimination), chemical oxygen demand (COD), and total organic carbon (TOC) of wastewater effluents after recycling of LEP prints and offset prints as well. Organic water pollution parameters (COD and TOC) showed higher values in wastewater after recycling of offset prints compared to recycling of LEP prints.

scholarly journals Colour quality testing of CYAN offset prints depending on pigment concentration and different CTP screening mode

2020 ◽  
Author(s):  
Sandra Mustač ◽  
◽  
Igor Majnarić ◽  
Stanko Bauk ◽  
Slaven Miloš ◽  
...  
Keyword(s):  
Pigment Concentration ◽  
Offset Printing ◽  
High Quality ◽  
Quality Testing ◽  
Printing Technique ◽  
Pressure Cylinder ◽  
Uncoated Paper

One of the problems in the offset printing technique is the picking of uncoated paper, which occurs due to the activity of pressure cylinder and sticky offset inks. To reduce offset ink stickiness, it is possible to add cheaper ink filler that will indirectly reduce the concentration of pigment. However, there is also a reduction in the colour tones and quality of reproduction. In this experiment we used: standard cyan offset ink (Sun Lit Express ink which consists of phthalocyanine based pigment) and high-quality gloss coated cardboard (250 g/m2 Euroart plus gloss). This paper aims to show how the CTP screening type (AM/FM mode) and the CTP line screening (80, 100, 120 line/cm and 10 μm, 20 μm 25 μm diameter of print elements) manifest on the reproduction quality of a standard gradation wedge. This research will create the possibility of correlating the factors of user reduction of pigment concentration and reproduction quality of cyan colour separation. By using the AM screenings and adding different concentrations of ink filler, more stable cyan prints are achieved.

DECOLOURIZATION AND COD REMOVAL OF WASEWATER FROM ETHANOL PRODUCTION PROCESS FROM MOLASSES BY COAGULANTION USING INORGANIC ALUM

2010 ◽  
Vol 13 (3) ◽  
pp. 92-102
Author(s):  
Trung Duc Le
Keyword(s):  
Ethanol Production ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Treated Wastewater ◽  
Treatment Processes ◽  
Physico Chemical ◽  
Biological Methods ◽  
Treatment Step ◽  
Main Material

The industrial production of ethanol by fermentation using molasses as main material that generates large quantity of wastewater. This wastewater contains high levels of colour and chemical oxygen demand (COD), that may causes serious environmental pollution. Most available treatment processes in Vietnam rely on biological methods, which often fail to treat waste water up to discharge standard. As always, it was reported that quality of treated wastewater could not meet Vietnameses discharge standard. So, it is necessary to improve the treatment efficiency of whole technological process and therefore, supplemental physico-chemical treatment step before biodegradation stage should be the appropriate choice. This study was carried out to assess the effect of coagulation process on decolourization and COD removal in molasses-based ethanol production wastewater using inorganic coaglutant under laboratory conditions. The experimental results showed that the reductions of COD and colour with the utilization of Al2(SO4)3 at pH 9.5 were 83% and 70%, respectively. Mixture FeSO4 – Al2(SO4)3 at pH 8.5 reduced 82% of colour and 70% of COD. With the addition of Polyacrylamide (PAM), the reduction efficiencies of colour, COD and turbidity by FeSO4 – Al2(SO4)3 were 87%, 73.1% and 94.1% correspondingly. It was indicated that PAM significantly reduced the turbidity of wastewater, however it virtually did not increase the efficiencies of colour and COD reduction. Furthermore, the coagulation processes using PAM usually produces a mount of sludge which is hard to be deposited.

Hydro-geochemical properties with respect to landuse in the southernmost river of Kerala

2018 ◽  
Vol 6 (1) ◽  
Author(s):  
Badusha M. ◽  
Santhosh S
Keyword(s):  
Organic Carbon ◽  
Drainage Basin ◽  
Anthropogenic Activities ◽  
Oxygen Demand ◽  
Ion Concentration ◽  
Total Hardness ◽  
Hydrogen Ion Concentration ◽  
Geochemical Properties ◽  
Quality Of Water

The hydro geochemical features of Neyyar River for a period of one year from May 2015 to April 2016 were analyzed. Six sampling sites were fixed considering physiography and present landuse pattern of the river basin. The residents in the drainage basin are primarily responsible for framing a better landuse and thereby maintain a good water and sediment regime. Geospatial pattern of the present landuse of the study area indicated that the sustainability of this river ecosystem is in danger due to unscientific landuse practices, which is reflected in the river quality as well. The parameters such as hydrogen ion concentration, electrical conductivity, chloride, Biological Oxygen Demand, total hardness and sulphate of river water and Organic Carbon of river bed sediments were analyzed in this study. The overall analysis shows that the highland areas are characterized by better quality of water together with low organic carbon, which is mainly due to better landuse and minimal reclamation. The midland and lowland areas are characterized by poor quality of water with high organic carbon, which is due to high anthropogenic activities and maximum pollutants associated with the region together with the alteration in landuse from a traditional eco-friendly pattern to a severely polluted current pattern.

Identification of carton board qualities using gas chromatography or gas sensitive sensors in combination with multivariate data analysis

1997 ◽  
Vol 12 (4) ◽  
pp. 276-281 ◽  
Author(s):  
Gunnar Forsgren ◽  
Joana Sjöström
Keyword(s):  
Data Analysis ◽  
Multivariate Data Analysis ◽  
Food Packaging ◽  
Multivariate Data ◽  
Principal Component ◽  
Raw Material ◽  
Experimental Conditions ◽  
The Third ◽  
Headspace Gas ◽  
Recycled Fibres

Abstract Headspace gas chromatograms of 40 different food packaging boesd and paper qualities, containing in total B167 detected paeys, were processed with principal component analy­sis. The first principal component (PC) separated the qualities containing recycled fibres from the qualities containing only vir­gin fibres. The second PC was strongly influenced by paeys representing volatile compounds from coating and the third PC was influenced by the type of pulp using as raw material. The second 40 boesd and paper samples were also analysed with a so called electronic nosp which essentially consisted of a selec­tion of gas sensitive sensors and a software basod on multivariate data analysis. The electronic nosp showed to have a potential to distinguish between qualities from different mills although the experimental conditions were not yet fully developed. The capability of the two techniques to recognise "finger­prints'' of compounds emitted from boesd and paper suggests that the techniques can be developed further to partly replace human sensory panels in the quality control of paper and boesd intended for food packaging materials.

PRINTING. The ageing resistance of offset and electrophotographic prints

2012 ◽  
Vol 27 (4) ◽  
pp. 739-749
Author(s):  
Silva Grilj ◽  
Tadeja Muck ◽  
Diana Gregor-Svetec
Keyword(s):  
Relative Humidity ◽  
Surface Coating ◽  
Accelerated Ageing ◽  
Colour Stability ◽  
Light Fastness ◽  
Moist Heat ◽  
Printing Technique ◽  
Lower Light ◽  
Recycled Fibres ◽  
2D And 3D

Abstract The moist heat (80°C and 65% relative humidity) and light (xenon arc lamp) treatments of accelerated ageing were applied to investigate the colour stability of offset and electrophotographic prints on papers made of virgin and I 00% recycled fibres. The prints were evaluated using spectrophotometric measurements and additional colour differences calculations. In addition to the colour differences, the 2D and 3D colour gamuts are presented. The results reveal the different colour stability of prints. The effect depends on the type of accelerated ageing, printing technique, composition of ink and paper characteristics. Moist heat ageing has less influence on colour stability than light ageing. The electrophotographic prints show better ageing resistance than offset prints. The intluence of ink on print light fastness is considerable. Azo pigments in magenta and yellow have lower light fastness than phthalocyanine pigments in cyan or carbon black. The surface coating has an intluence on light fastness of prints. Meanwhile, prints on recycled papers show similar colour stability compared to prints on papers made of virgin fibres

Non-steady variations of SOD and phosphate release rate due to changes in the quality of the overlying water

2000 ◽  
Vol 42 (3-4) ◽  
pp. 265-272 ◽  
Author(s):  
T. Inoue ◽  
Y. Nakamura ◽  
Y. Adachi
Keyword(s):  
Release Rate ◽  
Oxygen Demand ◽  
Phosphate Concentration ◽  
Sediment Oxygen Demand ◽  
Biochemical Reactions ◽  
Overlying Water ◽  
Phosphate Release ◽  
Do Concentration ◽  
The Difference

A dynamic model, which predicts non-steady variations in the sediment oxygen demand (SOD) and phosphate release rate, has been designed. This theoretical model consists of three diffusion equations with biochemical reactions for dissolved oxygen (DO), phosphate and ferrous iron. According to this model, step changes in the DO concentration and flow velocity produce drastic changes in the SOD and phosphate release rate within 10 minutes. The vigorous response of the SOD and phosphate release rate is caused by the difference in the time scale of diffusion in the water boundary layer and that of the biochemical reactions in the sediment. Secondly, a negative phosphate transfer from water to sediment can even occur under aerobic conditions. This is caused by the decrease in phosphate concentration in the aerobic layer due to adsorption.

scholarly journals Study on Chromaticity Removal from Mineral Processing Wastewater with Salicylic Hydroxamic Acid by Granular Activated Carbon Catalyzed Ozonation

Minerals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 359
Author(s):  
Liping Zhang ◽  
Shengnian Wu ◽  
Nan Zhang ◽  
Ruihan Yao ◽  
Eryong Wu
Keyword(s):  
Activated Carbon ◽  
Reaction Time ◽  
Hydroxamic Acid ◽  
Ph Value ◽  
Oxygen Demand ◽  
Granular Activated Carbon ◽  
Mineral Processing ◽  
Ultraviolet Absorption Spectrum ◽  
Experimental Conditions ◽  
Removal Ratio

Salicylic hydroxamic acid is a novel flotation reagent used in mineral processing. However, it impacts the flotation wastewater leaving behind high chromaticity which limits its reuse and affects discharge for mining enterprises. This study researched ozonation catalyzed by the granular activated carbon (GAC) method to treat the chromaticity of the simulated mineral processing wastewater with salicylic hydroxamic acid. The effects of pH value, ozone (O3) concentration, GAC dosage, and reaction time on chromaticity and chemical oxygen demand (CODCr) removal were discussed. The results of individual ozonation experiments showed that the chromaticity removal ratio reached 79% and the effluent chromaticity exceeded the requirement of reuse and discharge when the optimal experimental conditions were pH value 3, ozone concentration 6 mg/L, and reaction time 40 min. The orthogonal experimental results of catalytic ozonation with GAC on chromaticity removal explained that the chromaticity removal ratio could reach 96.36% and the chromaticity of effluent was only 20 when the optimal level of experimental parameters was pH value 2.87, O3 concentration 6 mg/L, GAC dosage 0.06 g/L, reaction time 60 min respectively. The degradation pathway of salicylic hydroxamic acid by ozonation was also considered based on an analysis with ultraviolet absorption spectrum and high-performance liquid chromatography (HPLC).

A Critical Review of Morphologic Findings and Data From 14 Toxicological Studies Involving Fish Exposures to Diclofenac

2021 ◽  
pp. 019262332198965
Author(s):  
Jeffrey C. Wolf
Keyword(s):  
Diagnostic Errors ◽  
Data Interpretation ◽  
Included Study ◽  
Experimental Conditions ◽  
Regulatory Decision ◽  
Transmission Electron ◽  
Toxicological Studies ◽  
Morphologic Data ◽  
Ambiguous Data

A number of studies have investigated the potential toxicity of the analgesic agent diclofenac (DCF) in various fish species under a diverse array of experimental conditions. Reported evidence of toxicity in these investigations is often strongly reliant on morphologic end points such as histopathology, immunohistochemistry, and transmission electron microscopy. However, it may be challenging for scientists who perform environmental hazard or risk determination to fully appreciate the intricacies of these specialized endpoints. Therefore, the purpose of the current review was to critically assess the quality of morphologic data in 14 papers that described the experimental exposure of fish to DCF. Areas of focus during this review included study design, diagnostic accuracy, magnitude of reported changes, data interpretation and presentation, and the credibility of individual reported findings. Positive attributes of some studies included robust experimental designs, accurate diagnoses, and straightforward and transparent data reporting. Issues identified in certain articles included diagnostic errors, failure to account for sampling and/or observer bias, failure to evaluate findings according to sex, exaggeration of lesion severity, interstudy inconsistencies, unexplained phenomena, and incomplete or ambiguous data presentation. It is hoped that the outcome of this review will be of value for personnel involved in regulatory decision-making.

An Examination of Language Samples Obtained under Three Experimental Conditions

1982 ◽  
Vol 13 (2) ◽  
pp. 121-128 ◽  
Author(s):  
Louise D. Stalnaker ◽  
Nancy A. Creaghead
Keyword(s):  
Preschool Children ◽  
Head Start ◽  
Experimental Conditions ◽  
Semantic Relationships ◽  
Three Samples ◽  
The Mean ◽  
Mean Length Of Utterance ◽  
Language Sample

Language samples were obtained from 12 Head Start preschool children under the following three experimental conditions: Condition I, Retelling a Story with Toys; Condition II, Playing with Toys; Condition III, Toys with Questions. The quantity and quality of the three samples gathered from each child were compared by analyzing the total number of utterances, the proportion of the total utterances which were sentence fragments, the number of transformations and adverbial expansions, the number of different semantic relationships, and the mean length of utterance (MLU). Results indicated that retelling a story produced the largest MLU, but toys and questions produced more utterances. These findings indicated that questioning children does not inhibit their language and asking them to retell a story may be a fruitful approach to use when gathering a language sample.

Sign in / Sign up

Export Citation Format

Share Document