scholarly journals Prediction and Evaluation of Waterjet Pump Performance under Nonuniform Inflow Using Parallel Compressor Theory

Water ◽  
2021 ◽  
Vol 13 (1) ◽  
pp. 99
Author(s):  
Puyu Cao ◽  
Rui Zhu
Keyword(s):  
Flow Instability ◽  
Internal Flow ◽  
Weighted Sum ◽  
Pump Performance ◽  
Inlet Velocity ◽  
Inlet Distortion ◽  
Pump Head ◽  
Compressor Performance ◽  
Waterjet Pump ◽  
External Characteristics

Parallel compressor theory (PCT) is commonly used to estimate effects of inlet distortion on compressor performance. As well as compressor, the actual inflow to pump is also nonuniform and unfavorable for performances. Nowadays, insufficient understanding of nonuniform inflow effects on pump performance restricts its development. Therefore, this paper applies PCT to predict external characteristics and evaluate internal flow instability of waterjet pump under nonuniform inflow. According to features of nonuniform inflow, the traditional PCT is modified and makes waterjet pump sub-divided into two circumferential tubes owning same performances but with different inlet velocity (representing nonuniform inflow). Above all, numerical simulation has been conducted to validated the applicability and accuracy of PCT in head prediction of waterjet pump under nonuniform inflow, since area-weighted sum of each tube head (i.e., theoretical pump head) is highly consistent with simulated result. Moreover, based on identifications of when and which tube occurs stall, PCT evaluates four stall behaviors of waterjet pump: partial deep stall, partial stall, pre-stall and full stall. Furthermore, different stall behavior generates different interactions between head variation of each tube, resulting in a multi-segment head curve under nonuniform inflow. The modified PCT with associated physical interpretations are expected to provide a sufficient understanding of nonuniform inflow effects on pump performances.

scholarly journals Effect of Blade Thickness on Internal Flow and Performance of a Plastic Centrifugal Pump

Machines ◽  
2022 ◽  
Vol 10 (1) ◽  
pp. 61
Author(s):  
Zhenfa Xu ◽  
Fanyu Kong ◽  
Lingfeng Tang ◽  
Mingwei Liu ◽  
Jiaqiong Wang ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Variable Thickness ◽  
Internal Flow ◽  
Constant Thickness ◽  
Element Analysis ◽  
Pump Performance ◽  
Blade Thickness ◽  
The Finite Element Analysis ◽  
Pump Head ◽  
And Performance

Blade thickness is an essential parameter of the impeller, which has significant effects on the pump performance. The plastic pump generally adopts thick blade due to low strength of plastic. The effects of blade thickness on the internal flow and performance of a plastic centrifugal pump were discussed based on the numerical methods. Two kinds of blade profile, the constant thickness blade (CTB) and the variable thickness blade (VTB), were investigated. The results indicated that, for the CTB, when the blade thickness was less than 6 mm, the pump performance did not change significantly. When the blade thickness exceeded 6 mm, the pump head and efficiency decreased rapidly. The pump head and efficiency of CTB 10 decreased by 42.2% and 30% compared with CTB 4, respectively. For the VTB, with blade thickness in a certain range (6 mm–14 mm), the pump performance changed slightly with the increased of trailing edge thickness. The minimum blade thickness of the plastic centrifugal pump should be 4 mm based on the finite element analysis. A variable thickness blade (VTB 4-8-4) with the maximum thickness located at 60% chord length was proposed to improve the pump performance, and its efficiency was 1.67% higher than that of the CTB 4 impeller.

scholarly journals Analysis of the Influence of Different Bionic Structures on the Noise Reduction Performance of the Centrifugal Pump

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 886
Author(s):  
Cui Dai ◽  
Chao Guo ◽  
Yiping Chen ◽  
Liang Dong ◽  
Houlin Liu
Keyword(s):  
Flow Field ◽  
Noise Reduction ◽  
Centrifugal Pump ◽  
Great Influence ◽  
Frequency Doubling ◽  
Sound Field ◽  
Internal Flow ◽  
Test System ◽  
Centrifugal Pumps ◽  
External Characteristics

The strong noise generated during the operation of the centrifugal pump harms the pump group and people. In order to decrease the noise of the centrifugal pump, a specific speed of 117.3 of the centrifugal pump is chosen as a research object. The bionic modification of centrifugal pump blades is carried out to explore the influence of different bionic structures on the noise reduction performance of centrifugal pumps. The internal flow field and internal sound field of bionic blades are studied by numerical calculation and test methods. The test is carried out on a closed pump test platform which includes external characteristics and a flow noise test system. The effects of two different bionic structures on the external characteristics, acoustic amplitude–frequency characteristics and flow field structure of a centrifugal pump, are analyzed. The results show that the pit structure has little influence on the external characteristic parameters, while the sawtooth structure has a relatively great influence. The noise reduction effect of the pit structure is aimed at the wide-band noise, while the sawtooth structure is aimed at the discrete noise of the blade-passing frequency (BPF) and its frequency doubling. The noise reduction ability of the sawtooth structure is not suitable for high-frequency bands.

Pump Performance Improvement by Restraining Back Flow in Screw-Type Centrifugal Pump

2005 ◽  
Vol 127 (4) ◽  
pp. 755-762 ◽  
Author(s):  
Yasushi Tatebayashi ◽  
Kazuhiro Tanaka ◽  
Toshio Kobayashi
Keyword(s):  
Pressure Fluctuations ◽  
Centrifugal Pumps ◽  
Two Phase ◽  
Simple Method ◽  
Back Flow ◽  
Pump Performance ◽  
Impeller Outlet ◽  
Pump Head ◽  
The Difference ◽  
Set Up

The authors have been investigating the various characteristics of screw-type centrifugal pumps, such as pressure fluctuations in impellers, flow patterns in volute casings, and pump performance in air-water two-phase flow conditions. During these investigations, numerical results of our investigations made it clear that three back flow regions existed in this type of pump. Among these, the back flow from the volute casing toward the impeller outlet was the most influential on the pump performance. Thus the most important factor to achieve higher pump performance was to reduce the influence of this back flow. One simple method was proposed to obtain the restraint of back flow and so as to improve the pump performance. This method was to set up a ringlike wall at the suction cover casing between the impeller outlet and the volute casing. Its effects on the flow pattern and the pump performance have been discussed and clarified to compare the calculated results with experimental results done under two conditions, namely, one with and one without this ring-type wall. The influence of wall’s height on the pump head was investigated by numerical simulations. In addition, the difference due to the wall’s effect was clarified to compare its effects on two kinds of volute casing. From the results obtained it can be said that restraining the back flow of such pumps was very important to achieve higher pump performance. Furthermore, another method was suggested to restrain back flow effectively. This method was to attach a wall at the trailing edge of impeller. This method was very useful for avoiding the congestion of solids because this wall was smaller than that used in the first method. The influence of these factors on the pump performance was also discussed by comparing simulated calculations with actual experiments.

Experimental Investigation of Surge Phenomena in a Transonic Centrifugal Compressor With Inlet Distortion

2020 ◽  
Author(s):  
Sasuga Ito ◽  
Masato Furukawa ◽  
Satoshi Gunjishima ◽  
Takafumi Ota ◽  
Kazuhito Konishi ◽  
...  
Keyword(s):  
Flow Rate ◽  
Centrifugal Compressor ◽  
Flow Instability ◽  
Pressure Sensors ◽  
Low Flow ◽  
Inlet Distortion ◽  
Transonic Centrifugal Compressor ◽  
Response Pressure ◽  
Surge Phenomena ◽  
Low Flow Rate

Abstract Inlet distortion has influence on the aerodynamic performance of turbomachinery such as compressors, turbines and fans. On turbochargers, bent pipes are installed around the compressor due to the spatial limitations in the engine room of the vehicle. As the result, the compressor is operated with the distorted inflow. In the low flow rate operation, the distorted inflow also affects the flow instability like stall and surge. Especially, the operation range on the low flow rate side is defined based on the flow rate where surge occurs, so it is important to investigate the effect of the distorted inflow on surge. In this study, the effect of the inlet distortion to surge phenomena has been investigated by the experiments with a transonic centrifugal compressor. A bent pipe has been installed at the upstream of the compressor to generate a distorted flow. Experiments have been also conducted under the condition that a straight pipe was installed upstream of the compressor, and unsteady measurements with high response pressure sensors and an I-type hot wire probe have been carried out to each experiments. In addition, Fast Fourier transform (FFT) and Wavelet transform have been applied to the unsteady measurement results obtained from each experiment.

3D Flow Simulation of a Twin-Screw Pump for the Analysis of Gap Flow Characteristics

2021 ◽  
Author(s):  
Ali Hassannejadmoghaddam ◽  
Boris Kutschelis ◽  
Frank Holz ◽  
Tomas Börjesson ◽  
Romuald Skoda
Keyword(s):  
Flow Rate ◽  
Volume Flow Rate ◽  
Overset Grid ◽  
3D Flow ◽  
Screw Pump ◽  
Pump Performance ◽  
Gap Flow ◽  
Wide Range ◽  
Twin Screw ◽  
Pump Head

Abstract Unsteady 3D flow simulations on a twin-screw pump are performed for an assessment of the radial, circumferential and flank gap flow effect on the pump performance. By means of the overset grid technique rigid computational grids around the counter-rotating spindles yield a high cell quality and a high spatial resolution of the gap backflow down to the viscous sublayer in terms of y^+ < 1 . An optimization of the hole-cutting process is performed on a generic gap flow and transferred to the complex moving gaps in the pump. Grid independence is ensured, and conservation properties of the overset grid interpolation technique are assessed. Simulation results are validated against measured pump characteristics. Pump performance in terms of pressure build-up along the flow path through the spindles and volume flow rate is presented for a wide range of spindle speed and pump head. Flow rate fluctuations are found to depend on head but hardly on speed. By a profound assessment of the respective radial, circumferential and flank gap contribution to the total backflow, the importance of the most complex flank gap is pointed out. Backflow rate characteristics in dependence on the pump head and the pump speed are presented.

scholarly journals Investigation of Flows in Rectangular Diffusers With Inlet Flow Distortion

1982 ◽  
Author(s):  
M. M. Al-Mudhafar ◽  
M. Ilyas ◽  
F. S. Bhinder
Keyword(s):  
Experimental Study ◽  
Velocity Profiles ◽  
Pressure Recovery ◽  
Two Dimensional ◽  
Flow Distortion ◽  
Inlet Flow ◽  
Inlet Velocity ◽  
Inlet Distortion ◽  
Mach Numbers ◽  
Inlet Flow Distortion

The results of an experimental study on the influence of severely distorted velocity profiles on the performance of a straight two-dimensional diffuser are reported. The data cover entry Mach numbers ranging from 0.1 to 0.6 and several inlet distortion levels. The pressure recovery progressively deteriorates as the inlet velocity is distorted.

scholarly journals Performance Improvement of a Liquid Molten Salt Pump: Geometry Optimization and Experimental Verification

Symmetry ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 423 ◽  
Author(s):  
Kai Wang ◽  
Xin Lu ◽  
Yu Li ◽  
Xianghui He ◽  
Houlin Liu ◽  
...  
Keyword(s):  
Molten Salt ◽  
Performance Improvement ◽  
Pressure Fluctuation ◽  
Geometry Optimization ◽  
Internal Flow ◽  
Experimental Methods ◽  
Sharp Corner ◽  
Hydraulic Efficiency ◽  
Low Velocity ◽  
Pump Performance

In order to enhance the hydraulic efficiency of a liquid molten salt pump, the improvement on the pump was carried out through numerical and experimental methods. The internal flow field obtained by the numerical simulation was analysed. The results show that there are low-velocity area in the scroll region and large curvature of the streamline at the outlet. Geometric modification was made by trimming the back-blades of the impeller and filleting the sharp corner of the outlet pipe. The modified pump performance was verified by the experiments. The hydraulic efficiency, the pressure fluctuation, vibration characteristics between the original and modified pump were compared. The results showed that the hydraulic efficiency of the modified pump increased 7.4%. In addition, the pressure fluctuation and vibration intensity were also reduced compared with the original pump. This result shows that the geometric modification improves not only the hydraulic performance but also the structural properties.

Pump Performance Improvement by Restraining Back Flow in Screw-Type Centrifugal Pump

2005 ◽  
Author(s):  
Yasushi Tatebayashi ◽  
Kazuhiro Tanaka ◽  
Toshio Kobayashi
Keyword(s):  
Pressure Fluctuations ◽  
Centrifugal Pumps ◽  
Two Phase ◽  
Simple Method ◽  
Back Flow ◽  
Pump Performance ◽  
Impeller Outlet ◽  
Pump Head ◽  
The Difference ◽  
Set Up

The authors have been investigating the various characteristics of screw-type centrifugal pumps, such as pressure fluctuations in impellers, flow patterns in volute casings, and pump performance in air-water two-phase flow conditions. During these investigations, numerical results of our investigations made it clear that three back flow regions existed in this type of pump. Among these, the back flow from the volute casing toward the impeller outlet was the most influential on the pump performance. Thus the most important factor to achieve higher pump performance was to reduce the influence of this back flow. One simple method was proposed to obtain the restraint of back flow and so as to improve the pump performance. This method was to set up a Ring-like wall at the suction cover casing between the impeller outlet and the volute casing. Its effects on the flow pattern and the pump performance have been discussed and clarified to compare the calculated results with experimental results done under two conditions — namely, one with and one without this Ring-type wall. The influence of wall’s height on the pump head was investigated by numerical simulations. In addition, the difference due to the wall’s effect was clarified to compare its effects on two kinds of volute casing. From the results obtained it can be said that restraining the back flow of such pumps was very important to achieve higher pump performance. Furthermore, another method was suggested to restrain back-flow effectively. This method was to attach a wall at the trailing edge of impeller. This method was very useful for avoiding the congestion of solids because this wall was smaller than that used in the first method. The influence of these factors on the pump performance was also discussed by comparing simulated calculations with actual experiments.

Sign in / Sign up

Export Citation Format

Share Document