scholarly journals Advanced oxidation of high concentrations of formaldehyde in aqueous solution under fluorescent and UV light

2021 ◽  
Vol 8 (4) ◽  
pp. 267-276
Author(s):  
Fatma Deniz ◽  
Mehmet Ali Mazmancı
Keyword(s):  
Aqueous Solution ◽  
Ph Value ◽  
Uv Light ◽  
Oxygen Demand ◽  
Advanced Oxidation ◽  
Cod Removal ◽  
Fluorescent Light ◽  
Order Kinetic ◽  
Ph Values ◽  
O2 Reduction

Background: Formaldehyde (FA) is a carcinogen compound, which is soluble in water. FA can be removed from aqueous solution using advanced oxidation methods. Methods: In this study, the oxidation of FA was studied under fluorescent and UV light. Hydrogen peroxide (H2 O2 ) was used as an oxidant. The pH value and H2 O2 amount of samples were optimized. The chemical oxygen demand (COD), FA concentration, and H2 O2 consumption were followed. Results: It was observed that the pH value of the sample was more significant under fluorescent light than UV light at oxidation of FA. The highest COD removal and H2 O2 reduction were 18.57 and 30.90%, respectively, at pH 12.00, with a 1:1 ratio of FA:H2 O2 under fluorescent light. 86.41% FA and 62.12% COD removal were achieved at pH 7.00, with a 1:2 ratio of FA:H2 O2 , under UV light. It was observed that H2 O2 was consumed at all pH values under UV light. On the other hand, under fluorescent light, the concentration of H2 O2 decreased only at pH 12. In control samples containing only H2 O2 , the H2 O2 reduction was 92.09% at pH 11.91, while it was 2-6% at other pH levels under fluorescent light. The H2 O2 reduction changed between 33 and 44% at different pH values under UV light. The oxidation of FA was found to be suitable for the pseudo-first-order kinetic model and Langmuir isotherm model. Conclusion: The most effective oxidation was obtained at the original pH value (7.00) and 1:2 ratio of FA:H2 O2 under UV light.

scholarly journals Performance Evaluation of Ultra-Violet Light and Iron Oxide Nanoparticles for the Treatment of Synthetic Petroleum Wastewater: Kinetics of COD Removal

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5012
Author(s):  
Cecilia O. Akintayo ◽  
Omolola H. Aremu ◽  
Wilfred N. Igboama ◽  
Simphiwe M. Nelana ◽  
Olushola S. Ayanda
Keyword(s):  
Electron Microscopy ◽  
Iron Oxide ◽  
Iron Oxide Nanoparticles ◽  
Uv Light ◽  
Oxygen Demand ◽  
Ultra Violet ◽  
Cod Removal ◽  
Infrared Spectrometry ◽  
Oxide Nanoparticles ◽  
Order Kinetic

In this study, the use of ultra-violet (UV) light with or without iron oxide nanoparticles (IONPs) for the degradation of synthetic petroleum wastewater was investigated. The IONPs was synthesised by sodium borohydride reduction of ferric chloride solution and was characterised by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FTIR), x-ray fluorescence spectrophotometry (XRF), and energy dispersive spectroscopy (EDS). The amount of degradation was evaluated by chemical oxygen demand (COD) determination. Experimental results show that the COD removal from synthetic petroleum wastewater by IONPs/UV system was more effective than they were independently. The combination of UV light at a wavelength of 254 nm, pH of 8, and 1.0 g of IONPs resulted in COD removal from 10.5% up to 95.5%. The photocatalytic degradation of synthetic petroleum wastewater is about 1.3–2.0 times faster in comparison to UV light only. The removal of COD from synthetic petroleum wastewater by UV light and IONPs follows the pseudo-first-order kinetic model with rate constant k ranging from 0.0133 min−1 to 0.0269 min−1. Consequently, this study has shown that the use of UV light in the presence of IONPs is favourable and effective for the removal of organic pollutants from petroleum refinery wastewater.

Adsorption Characteristics of Phenol in Aqueous Solution by Pinus massoniana Biochar

2013 ◽  
Vol 295-298 ◽  
pp. 1154-1160 ◽  
Author(s):  
Guo Zhi Deng ◽  
Xue Yuan Wang ◽  
Xian Yang Shi ◽  
Qian Qian Hong
Keyword(s):  
Aqueous Solution ◽  
Ph Value ◽  
Pinus Massoniana ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Adsorbent Dosage ◽  
Salt Ions ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The objective of this paper is to investigate the feasibility of phenol adsorption from aqueous solution by Pinus massoniana biochar. Adsorption conditions, including contact time, initial phenol concentration, adsorbent dosage, strength of salt ions and pH, have been investigated by batch experiments. Equilibrium can be reached in 24 h for phenol from 50 to 250 mg• L-1. The optimum pH value for this kind of biochar is 5.0. The amount of phenol adsorbed per unit decreases with the increase in adsorbent dosage. The existence of salt ions makes negligible influence on the equilibrium adsorption capacity. The experimental data is analyzed by the Freundlich and Langmuir isotherm models. Equilibrium data fits well to the Freundlich model. Adsorption kinetics models are deduced and the pseudo-second-order kinetic model provides a good correlation for the adsorbent process. The results show that the Pinus massoniana biochar can be utilized as an effective adsorption material for the removal of phenol from aqueous solution.

scholarly journals TiO2 BEADS FOR PHOTOCATALYTIC DEGRADATION OF HUMIC ACID IN PEAT WATER

2011 ◽  
Vol 11 (3) ◽  
pp. 253-257 ◽  
Author(s):  
Winarti Andayani ◽  
Agustin N M Bagyo
Keyword(s):  
Aqueous Solution ◽  
Humic Acid ◽  
Oxalic Acid ◽  
Chemical Oxygen Demand ◽  
Photocatalytic Degradation ◽  
Uv Light ◽  
Batch Reactor ◽  
Oxygen Demand ◽  
Color Intensity ◽  
Before And After

Degradation of humic acid in aqueous solution containing TiO2 coated on ceramics beads under irradiation of 254 nm UV light has been conducted in batch reactor. The aim of this experiment was to study photocatalytic degradation of humic acid in peat water. The irradiation of the humic acid in aqueous solution was conducted in various conditions i.e solely uv, in the presence of TiO2-slurry and TiO2 beads. The color intensity, humic acid residue, conductivity and COD (chemical oxygen demand) of the solution were analyzed before and after irradiation.  The compounds produced during photodegradation were identified using HPLC. The results showed that after photocatalytic degradation, the color intensity and the COD value of the solution decreased, while the conductivity of water increased indicating mineralization of the peat water occurred. In addition, oxalic acid as the product of degradation was observed.

Adsorption of cadmium by biochar produced from pyrolysis of corn stalk in aqueous solution

2016 ◽  
Vol 74 (6) ◽  
pp. 1335-1345 ◽  
Author(s):  
Fengfeng Ma ◽  
Baowei Zhao ◽  
Jingru Diao
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Ionic Strength ◽  
Ph Value ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Corn Stalk ◽  
Adsorbent Dosage ◽  
Initial Ph ◽  
Adsorbent Particle

The purpose of this work is to investigate adsorption characteristic of corn stalk (CS) biochar for removal of cadmium ions (Cd2+) from aqueous solution. Batch adsorption experiments were carried out to evaluate the effects of pH value of solution, adsorbent particle size, adsorbent dosage, and ionic strength of solution on the adsorption of Cd2+ onto biochar that was pyrolytically produced from CS at 300 °C. The results showed that the initial pH value of solution played an important role in adsorption. The adsorptive amount of Cd2+ onto the biochar decreased with increasing the adsorbent dosage, adsorbent particle size, and ionic strength, while it increased with increasing the initial pH value of solution and temperature. Cd2+ was removed efficiently and quickly from aqueous solutions by the biochar with a maximum capacity of 33.94 mg/g. The adsorption process was well described by the pseudo-second-order kinetic model with the correlation coefficients greater than 0.986. The adsorption isotherm could be well fitted by the Langmuir model. The thermodynamic studies showed that the adsorption of Cd2+ onto the biochar was a spontaneous and exothermic process. The results indicate that CS biochar can be considered as an efficient adsorbent.

Metal Adsorbent Prepared from Coir Pith as Agricultural Waste: Adsorption of Zn(II) and Pb(II) from Aqueous Solution

2013 ◽  
Vol 545 ◽  
pp. 101-108 ◽  
Author(s):  
Kitirote Wantala ◽  
Nusavadee Pojananukij ◽  
Pongsert Sriprom ◽  
Tinnakorn Kumsaen ◽  
Arthit Neramittagapong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Calcination Temperature ◽  
Ph Value ◽  
Agricultural Waste ◽  
Initial Solution ◽  
Order Kinetic ◽  
Solution Ph ◽  
Freundlich Isotherms ◽  
Coir Pith

Adsorption of Zn(II) and Pb(II) from aqueous solution were studied by using modified coir pith as an adsorbent. The extended adsorption conditions were investigated as a function of calcination temperature, contact time, adsorbent size, initial pH of solution and initial Zn(II) and Pb(II) concentrations. The adsorption capacity increased rapidly in first 5 minute and reached equilibrium in 120 minutes for Zn(II) and 10 minutes for Pb(II). In case of Zn(II); the results showed that the calcination temperature of modified coir pith above 600oC gave the higher adsorption capacity. The sizes of modified coir pith have no effect on the adsorption capacity. The adsorption capacity increased with increasing initial solution pH value. In case of Pb(II); the calcination temperature of modified coir pith showed no effect on the adsorption capacity. The sizes of modified coir pith showed a little effect on the adsorption capacity. The adsorption capacity increased with increasing of initial solution pH value up to pH of 3 and then stable. The results also corresponded with the Langmuir and Freundlich isotherms and pseudo second order kinetic adsorption models. The modified coir pith gave a higher Zn(II) and Pb(II) adsorption capacity of 29.33 mg Zn(II)/g adsorbent and 36.50 mg Pb(II)/g adsorbent, respectively.

scholarly journals Study on Anodic Oxidation parameters for removal of pesticide Imidacloprid on a modified tantalum surface by lead dioxide film

2020 ◽  
Keyword(s):  
Current Density ◽  
Crop Production ◽  
Ph Value ◽  
Lead Dioxide ◽  
Oxygen Demand ◽  
Electrochemical Process ◽  
Order Kinetic ◽  
Initial Ph ◽  
Transport Control ◽  
Dioxide Film

<p>The commercial imidacloprid (IMD) insecticide [1-(6-chloro-3-pyridinyl) methyl-4,5-dihydro-N-nitro-1H-imidazole-2-amine] is widely used for the enhancement of crop production, but the intensive use of this insecticide has caused serious environmental problems. This work presents an electrochemical process for the removal of this insecticide using galvanostatic electrolysis at modified tantalum surface by lead dioxide film anode (Ta(PbO2)) anode. The electrolytic process was monitored by chemical oxygen demand (COD). The influence of operating parameters, such as current density, initial concentration of IMD, temperature and initial pH value was investigated. The COD decay follows a pseudo first-order kinetic and the process was under mass transport control. COD removal reach 97% when using an apparent current density of 100 mA cm−2, initial COD of 953 mg L−1 and at 25 °C after 4.5 h electrolysis time.</p>

scholarly journals Kinetics, Isotherm and Thermodynamic Studies for Efficient Adsorption of Congo Red Dye from Aqueous Solution onto Novel Cyanoguanidine-Modified Chitosan Adsorbent

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4446
Author(s):  
Nouf F. Al-Harby ◽  
Ebtehal F. Albahly ◽  
Nadia A. Mohamed
Keyword(s):  
Aqueous Solution ◽  
Congo Red ◽  
Adsorption Process ◽  
Ph Value ◽  
Dye Adsorption ◽  
Order Kinetic ◽  
Amino Groups ◽  
Solution Ph ◽  
Intraparticle Diffusion Model ◽  
Modified Chitosan

Novel Cyanoguanidine-modified chitosan (CCs) adsorbent was successfully prepared via a four-step procedure; first by protection of the amino groups of chitosan, second by insertion of epoxide rings, third by opening the latter with cyanoguanidine, and fourth by restoring the amino groups through elimination of the protection. Its structure and morphology were checked using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The adsorption capacity of CCs for Congo Red (CR) dye was studied under various conditions. It decreased significantly with the increase in the solution pH value and dye concentration, while it increased with increasing temperature. The adsorption fitted to the pseudo-second order kinetic model and Elovich model. The intraparticle diffusion model showed that the adsorption involved a multi-step process. The isotherm of CR dye adsorption by CCs conforms to the Langmuir isotherm model, indicating the monolayer nature of adsorption. The maximum monolayer coverage capacity, qmax, was 666.67 mg g−1. Studying the thermodynamic showed that the adsorption was endothermic as illustrated from the positive value of enthalpy (34.49 kJ mol−1). According to the values of ΔG°, the adsorption process was spontaneous at all selected temperatures. The value of ΔS° showed an increase in randomness for the adsorption process. The value of activation energy was 2.47 kJ mol−1. The desorption percentage reached to 58% after 5 cycles. This proved that CCs is an efficient and a promising adsorbent for the removal of CR dye from its aqueous solution.

Preparation and Fluorescence Properties of GdF3:Eu3+, NaGdF4:Eu3+ Materials

2013 ◽  
Vol 661 ◽  
pp. 74-78
Author(s):  
Li Li Wang ◽  
Lian Li Liu ◽  
Qian Xu ◽  
Tong Sun ◽  
Wan Na Gu
Keyword(s):  
Aqueous Solution ◽  
Phase Composition ◽  
Polyethylene Glycol ◽  
Ph Value ◽  
Hexagonal Phase ◽  
Raw Material ◽  
Fluorescence Properties ◽  
X Ray ◽  
Ph Values ◽  
Molecular Fluorescence

The GdF3:Eu3+and NaGdF4:Eu3+powders were synthesized by hydrothermal method as raw material of Gd2O3, Eu2O3, NaF, NH4HF2, EDTA and polyethylene glycol. The powders were characterized by means of X-ray powder diffraction, SEM microscopy and Molecular fluorescence photometer. It was discussed that the pH value of aqueous solution had affection on the phase composition of synthesized powders. The complex fluorides GdF3and NaGdF4were synthesized in aqueous solution at the pH values between 3 and 6. The synthesized powders were single hexagonal phase of NaGdF4 crystal at pH=8. It was also found that different fluorescence properties were exhibited by Eu3+doping powders synthesized at different pH values of aqueous solution. The synthesized powders of GdF3and NaGdF4were excellent fluorescence materials.

scholarly journals Automotive fleet repair facility wastewater treatment using air/ZVI and air/ZVI/H2O2 processes

2017 ◽  
Vol 43 (3) ◽  
pp. 24-31 ◽  
Author(s):  
Jan Paweł Bogacki ◽  
Hussein Al-Hazmi
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Treatment Effectiveness ◽  
Ph Value ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Process Time ◽  
Process Conditions ◽  
Cod Removal Efficiency ◽  
Repair Facility

AbstractAdvanced automotive fleet repair facility wastewater treatment was investigated with Zero-Valent Iron/Hydrogen Peroxide (Air/ZVI/H2O2) process for different process parameters: ZVI and H2O2doses, time, pH. The highest Chemical Oxygen Demand (COD) removal efficiency, 76%, was achieved for ZVI/H2O2doses 4000/1900 mg/L, 120 min process time, pH 3.0. COD decreased from 933 to 227 mg/L. In optimal process conditions odor and color were also completely removed. COD removal efficiency was increasing with ZVI dose. Change pH value below and over 3.0 causes a rapid decrease in the treatment effectiveness. The Air/ZVI/H2O2process kinetics can be described as d[COD]/dt = −a [COD]tm, where ‘t’ corresponds with time and ‘a’ and ‘m’ are constants that depend on the initial reagent concentrations. H2O2influence on process effect was assessed. COD removal could be up to 40% (560 mg/L) for Air/ZVI process. The FeCl3coagulation effect was also evaluated. The best coagulation results were obtained for 700 mg/L Fe3+dose, that was slightly higher than dissolved Fe used in ZVI/H2O2process. COD was decreased to 509 mg/L.

scholarly journals Photo-degradation ibuprofen by UV/H2O2 process: response surface analysis and degradation mechanism

2017 ◽  
Vol 75 (12) ◽  
pp. 2935-2951 ◽  
Author(s):  
Mingguo Peng ◽  
Huajie Li ◽  
Xu Kang ◽  
Erdeng Du ◽  
Dongdong Li
Keyword(s):  
Aqueous Solution ◽  
Response Surface ◽  
Ph Value ◽  
Uv Light ◽  
Degradation Products ◽  
Degradation Mechanism ◽  
Oh Radical ◽  
Initial Ph ◽  
Rsm Model ◽  
Degradation Intermediates

The removal of ibuprofen (IBP) in aqueous solution using UV/H2O2 process was evaluated. The response surface methodology (RSM) and Box–Behnken design were employed to investigate the effects of process parameters on IBP removal, including the initial IBP concentration, H2O2 dosage, UV light intensity, and initial pH value of solution. The RSM model developed herein fits well with the experiments, and provides a good insight into the OH radical irritated degradation mechanisms and kinetics. High resolution accurate mass spectrometry coupled with liquid chromatography was used to identify the degradation intermediates. A total of 23 degradation products were identified, including mono-hydroxylated products and dihydroxylated products. A series of OH radical-initiated reactions, including hydroxylation, dihydroxylation, decarboxylation, demethylation, ring break, lead to the final mineralization of IBP to CO2 and H2O. UV/H2O2 technology could be a promising technology for IBP removal in aqueous solution.

Sign in / Sign up

Export Citation Format

Share Document