scholarly journals Process Parameter Influence on Tensile Property of Friction Stir Processed Al/Ni-Fe Composite

2020 ◽  
Vol 31 ◽  
pp. 59-64
Author(s):  
L. Magondo ◽  
M. B. Shongwe ◽  
R. M. Mahamood ◽  
S. A. Akinlabi ◽  
S. Hassan ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Tensile Property ◽  
Process Parameters ◽  
Rotational Speed ◽  
Processing Parameters ◽  
Processing Technique ◽  
Matrix Composites ◽  
Friction Stir ◽  
State Processing ◽  
Made In

Friction stir processing (FSP) is a solid-state processing technique that has proven to be an efficient surface modification process for producing aluminium matrix composites (AMCs). However, practical challenges still occur during the processing of AMCs even though extensive progress has been made in recent years. In the present study, the influence of FSP process parameters on the tensile property of Al-Ni-Fe composite has been investigated. The process parameters studied were rotational speed and advancing speed. The rotational speed varied between 600 and 1000 rpm while the advancing speed varied between 70 and 210 mm/min. The rotational speed was kept constant at each setting and the advancing speed varied. Other processing parameters were kept constant throughout the experiments. The results were compared with those of the base metal (Al). The results showed that the tensile strength decreased as the advancing speed increased. The highest tensile strength was obtained at a rotational speed of 1000 rpm and an advancing speed of 70 mm/min.

Effect of Process Parameters on Defect Formation in Friction Stir Processed 6082-T6 Aluminium Alloy

2012 ◽  
Vol 232 ◽  
pp. 3-7
Author(s):  
Akinlabi Esther Titilayo ◽  
Akinlabi Stephen Akinwale
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Aluminium Alloy ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Feed Rate ◽  
Rotational Speed ◽  
Defect Formation ◽  
Processing Parameters ◽  
Friction Stir

This paper reports the effects of processing parameters on defects formed during friction stir processing of 6082-T6 Aluminium Alloy. The plates were processed by varying the feed rate between 50 and 250 mm/min, while the rotational speed was varied between 1500 and 3500 rpm to achieve the best result. It was observed that the sheets processed at the highest feed rate considered in this research resulted in wormhole defect. These processed samples with defects were correlated to the tensile results and it was found that the Ultimate Tensile Strength (UTS) of these samples was relatively low compared to other samples without defects.

scholarly journals Fabrication of AA7075 Hybrid Green Metal Matrix Composites by Friction Stir Processing Technique

2020 ◽  
Vol 44 (4) ◽  
pp. 295-300
Author(s):  
Sanjay Kumar ◽  
Ashish Kumar Srivastava ◽  
Rakesh Kumar Singh
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Research Work ◽  
Processing Technique ◽  
Matrix Composites ◽  
Avant Garde ◽  
Friction Stir ◽  
Surface Composites ◽  
Tool Tilt Angle

Friction stir processing is an avant-garde technique of producing new surface composite or changing the different properties of a material through intense, solid-state localized material plastic deformation. This change in properties depends upon the deformation formed by inserting a non-consumable revolving tool into the workpiece and travels laterally through the workpiece. This research work highlights the effect of process parameters on mechanical properties of fabricated surface composites by friction stir processing. By using various reinforcing materials like Ti, SiC, B4C, Al2O3 with waste elements like waste eggshells, rice husks, coconut shell and coir will be used to fabricate the green composites which are environmentally friendly and reduces the problem of decomposition. The parameter for this experiment is considered as the reinforcing materials, tool rotation speed and tool tilt angle. The SiC/Al2O3/Ti along with eggshell are selected asreinforcement materials. The main effect of the reinforcement is to improve mechanical properties, like hardness, impact strength and strength. The results revealed that the process parameters significantly affect the mechanical properties of friction stir processed surface composites.

Optimization of friction stir welding process parameters for AA6063-ETP copper using central composite design

2020 ◽  
Vol 17 (4) ◽  
pp. 491-507 ◽  
Author(s):  
Nitin Panaskar ◽  
Ravi Prakash Terkar
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Content Type ◽  
Friction Stir ◽  
Central Composite

Purpose Recently, several studies have been performed on lap welding of aluminum and copper using friction stir welding (FSW). The formation of intermetallic compounds at the weld interface hampers the weld quality. The use of an intermediate layer of a compatible material during welding reduces the formation of intermetallic compounds. The purpose of this paper is to optimize the FSW process parameters for AA6063-ETP copper weld, using a compatible zinc intermediate filler metal. Design/methodology/approach In the present study, a three-level, three-factor central composite design (CCD) has been used to determine the effect of various process parameters, namely, tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil on ultimate tensile strength of the weld. A total of 60 experimental data were fitted in the CCD. The experiments were performed with tool rotational speeds of 1,000, 1,200 and 1,400 rpm each of them with tool traverse speeds of 5, 10 and 15 mm/min. A zinc inter-filler foil of 0.2 and 0.4 mm was also used. The macrograph of the weld surface under different process parameters and the tensile strength of the weld have been investigated. Findings The feasibility of joining 3 mm thick AA6063-ETP copper using zinc inter-filler is established. The regression analysis showed a good fit of the experimental data to the second-order polynomial model with a coefficient of determination (R2) value of 0.9759 and model F-value of 240.33. A good agreement between the prediction model and experimental findings validates the reliability of the developed model. The tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil significantly affected the tensile strength of the weld. The optimal conditions found for the weld were, rotational speed of 1,212.83 rpm and traverse speed of 9.63 mm/min and zinc foil thickness is 0.157 mm; by using optimized values, ultimate tensile strength of 122.87 MPa was achieved, from the desirability function. Originality/value Aluminium and copper sheets could be joined feasibly using a zinc inter-filler. The maximum tensile strength of joints formed by inter-filler (122.87 MPa) was significantly better as compared to those without using inter-filler (83.78 MPa). The optimum process parameters to achieve maximum tensile strength were found by CCD.

Process Parameters Optimization of Friction Stir Welding in Aluminium Alloy 6063-T6 by Taguchi Method

2017 ◽  
Vol 867 ◽  
pp. 97-104 ◽  
Author(s):  
T. Ganapathy ◽  
K. Lenin ◽  
K. Pannerselvam
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Taguchi Method ◽  
Axial Force ◽  
Process Parameters ◽  
Welding Speed ◽  
Rotational Speed ◽  
Process Parameter ◽  
Main Process ◽  
Friction Stir

This paper deals with the effective application of friction stir welding similar to butt joining technique.AL6063 T-6 alloys prepared in 125x 100 x 7mm thickness plate and FSW tool setup were H13 of diameter 25mm rotary tool with straight cylindrical pin profile. The maximum strength was considered for selection of combined process parameter. The process parameters were optimized using Taguchi method. The Rotational speed, welding speed, and axial speed are the main process parameter which taken into our consideration. The optimum process parameters are determined with reference to tensile strength of the joint. From the experiments, it was found the effects of welding parameter are the axial force is highest substantial parameter to determining the tensile strength of the joint. The paper which revealed the optimal values of process parameter are to acquire a maximum tensile strength of friction stir welded AL6063-T6 plates is 101.6Mpa with the combination level of rotational speed, welding speed and axial force are found to be 1100 RPM, 60 mm/min and 12.5 KN. validation test was carried out and results were nearer to the optimized results confirmed by the optimum results.

Analysis of process parameters effects on underwater friction stir welding of aluminum alloy 6082-T6

2018 ◽  
Vol 233 (6) ◽  
pp. 1700-1710 ◽  
Author(s):  
Mohd Atif Wahid ◽  
Zahid A Khan ◽  
Arshad Noor Siddiquee ◽  
Rohit Shandley ◽  
Nidhi Sharma
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Underwater Friction Stir Welding ◽  
Optimal Setting

In friction stir welding of heat treatable aluminum alloys, the thermal cycles developed during the joining process result in softening of the joints which adversely affect their mechanical properties. Underwater friction stir welding can be a process of choice to overcome this problem due to low peak temperature and short dwell time involved during the process. Consequently, this article presents a study pertaining to the underwater friction stir welding of aluminum alloy 6082-T6 with an aim to develop a mathematical model to optimize the underwater friction stir welding process parameters for obtaining maximum tensile strength. The results of the study reveal that the tool shoulder diameter (d), tool rotational speed (ω), welding speed (v), and second-order term of rotational speed, that is, ω2, significantly affect the tensile strength of the joint. The maximum tensile strength of 241 MPa which is indeed 79% of the base metal strength and 10.7% higher than that of conventional (air) friction stir welding joint was achieved at an optimal setting of the underwater friction stir welding parameters, that is, tool rotational speed of 900 r/min, the welding speed of 80 mm/min, and a tool shoulder of 17 mm. The article also presents the results of temperature variation, the macrostructural and microstructural investigations, microhardness, and fractography of the joint obtained at the optimal setting for underwater friction stir welded (UFSWed) joint.

Investigations on the Effect of Tool Speed and Feed Rate on the Friction Stir Processed AZ31B Magnesium Alloys

2012 ◽  
Vol 622-623 ◽  
pp. 700-704
Author(s):  
D. Peter Pushpanathan ◽  
K. Ganesa Balamurugan ◽  
K. Mahadevan
Keyword(s):  
Tensile Strength ◽  
Processing Technique ◽  
Wear Rates ◽  
Friction Stir ◽  
Mechanical And Tribological Properties ◽  
Full Factorial ◽  
Hardness Values ◽  
Level 2 ◽  
State Processing ◽  
Minimum Wear

The friction stir processing is a solid state processing technique. The present study investigates the effect of process parameters like tool rotational speed and tool feed on the mechanical and tribological properties of friction stir processed AZ31B magnesium alloy. The experiments were conducted with 3 level 2 factors full factorial design with two replications. The responses were tensile strength, microhardness and wear. The investigation reveals that both the tensile strength and microhardness values were decreasing with decreasing grain size. The minimum wear rates were observed at higher hardness values.

Optimization of process parameters for friction stir welding of joining A6061 and A6082 alloys by Taguchi method

2012 ◽  
Vol 227 (6) ◽  
pp. 1150-1163 ◽  
Author(s):  
Sanjay Kumar ◽  
Sudhir Kumar ◽  
Ajay Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Experimental Tests ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Optimization Of Process Parameters ◽  
Tool Pin

The friction stir welding is a pioneering solid-state metal joining technique for producing high-quality joints in materials. In this article, Taguchi approach is applied to analyze the optimal process parameters for optimum tensile strength and hardness of welded dissimilar A6061 and A6082 alloys. An orthogonal array of L9 is implemented and the analysis of variance is employed to investigate the importance of parameters on responses. The experimental tests, conducted according to combination of rotational speed, tool tilt and types of tool pin profile parameters. The results indicate that the rotational speed is most significant process parameter that has the highest influence on tensile strength and hardness, followed by tool pin profile and tool tilt. The optimum results verified by conducting confirmation experiments. The predicted optimal value of tensile strength and hardness of dissimilar joints produced by friction stir welding are 267.74 MPa and 80.55 HRB, respectively.

scholarly journals Optimization of process parameters of friction stir welded AA 5083-O aluminum alloy using Response Surface Methodology

2015 ◽  
Vol 63 (4) ◽  
pp. 851-855 ◽  
Author(s):  
S. Jannet ◽  
P. Koshy Mathews ◽  
R. Raja
Keyword(s):  
Tensile Strength ◽  
Response Surface Methodology ◽  
Ultimate Tensile Strength ◽  
Response Surface ◽  
Process Parameters ◽  
Welding Speed ◽  
Rotational Speed ◽  
Strength Analysis ◽  
Aluminum Compound ◽  
Friction Stir

Abstract A methodology was exhibited to create the experimental model for assessing the Ultimate Tensile Strength of AA 5083-O aluminum compound which is broadly utilized as a part of boat building industry by Friction Stir Welding (FSW). FSW process parameters, such as: tool rotational speed, welding speed, and axial force were optimized for better results. FSW was completed considering three-component 3-level Box Behnekn Design. Response surface Methodology (RSM) was implemented to obtain the relationship between the FSW process parameters and ultimate Tensile Strength. Analysis of Variance (ANOVA) procedure was utilized to check the aptness of the created model. The FSW process parameters were additionally streamlined utilizing Response Surface Methodology (RSM) to augment tensile strength. The joint welded at a rotational speed of 1100 rpm, a welding speed of 75 mm/min and a pivotal energy of 2.5 t displays higher tensile strength compared with different joints in comparison with other joints.

Parametric optimization of friction stir welding process parameters of dissimilar welded joints using grey relational analysis and desirability function approach

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Bhanodaya Kiran Babu Nadikudi
Keyword(s):  
Tensile Strength ◽  
Process Parameters ◽  
Tilt Angle ◽  
Grey Relational Analysis ◽  
Rotational Speed ◽  
Tool Rotational Speed ◽  
Content Type ◽  
Friction Stir ◽  
Relational Analysis ◽  
Grey Relational

Purpose The main purpose of the present work is to study the multi response optimization of dissimilar friction stir welding (FSW) process parameters using Taguchi-based grey relational analysis and desirability function approach (DFA). Design/methodology/approach The welded sheets were fabricated as per Taguchi orthogonal array design. The effects of tool rotational speed, transverse speed and tool tilt angle process parameters on ultimate tensile strength and hardness were analyzed using grey relational analysis, and DFA and optimum parameters combination was determined. Findings The tensile strength and hardness values were evaluated from the welded joints. The optimum values of process parameters were estimated through grey relational analysis and DFA methods. Similar kind of optimum levels of process parameters were obtained through two optimization approaches as tool rotational speed of 1150 rpm, transverse speed of 24 mm/min and tool tilt angle of 2° are the best process parameters combination for maximizing both the tensile strength and hardness. Through these studies, it was confirmed that grey relational analysis and DFA methods can be used to find the multi response optimum values of FSW process parameters. Research limitations/implications In the present study, the FSW is performed with L9 orthogonal array design with three process parameters such as tool rotational speed, transverse speed and tilt angle and three levels. Practical implications Aluminium alloys are widely using in automotive and aerospace industries due to holding a high strength to weight property. Originality/value Very limited work had been carried out on multi objective optimization techniques such as grey relational analysis and DFA on friction stir welded joints made with dissimilar aluminium alloys sheets.

Optimization Analysis of Process Parameters of Friction Stir Welded Dissimilar Joints of Aluminium Alloys

2017 ◽  
Vol 867 ◽  
pp. 112-118
Author(s):  
Subburaj Rajesh Kannan ◽  
J. Lakshmipathy ◽  
M. Vignesh Kumar ◽  
K. Manisekar ◽  
N. Murugan
Keyword(s):  
Tensile Strength ◽  
Process Parameters ◽  
Rotational Speed ◽  
Welding Process ◽  
Welding Parameters ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Optimum Parameters ◽  
Aluminum Plates ◽  
Aluminum 7075

Friction stir welding (FSW) is one of the new technique for welding materials in solid state welding process. In this proposed work we are using FSW to join the two dissimilar alloys of aluminium. The 6mm thick aluminum plates of aluminium 5086 and aluminum 7075 plates are considered for welding. These have been considered due to their application in various fields. In this experimental process Taguchi’s L9 orthogonal array method is used for optimizing the three process parameters namely rotational speed, axial force and welding speed. To produce a better joint the tensile strength is predicted for the optimum welding parameters and also their percentage of contribution is calculated, by applying the effect of analysis of variance. Depends upon the experimental study, the rotational speed is found better over the other process parameters, which enhances the quality of the weld. The tensile strength has been found for the optimum parameters and the result found during the experiment was 290Mpa which was higher than the base metal strength of aluminium 5086 alloy. The SEM fractograph analysis was done on the optimum parameters welded joints to show the fracture behaviour of tensile test which justifies the visual inspection results of brittle and ductile failures.

Sign in / Sign up

Export Citation Format

Share Document