scholarly journals Perbandingan Pengujian Konsolidasi Menggunakan Alat Rowe Cell dan Oedometer pada Tanah Lanau Lunak

2020 ◽  
Vol 22 (2) ◽  
pp. 149-155
Author(s):  
Iskandar ◽  
Rabiya
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Soil Samples ◽  
Soil Parameters ◽  
Soil Consolidation ◽  
Test Results ◽  
Soft Soils ◽  
Better Than ◽  
Rowe Cell

Soil consolidation testing using an oedometer and rowe cell. Oedometers are often used on clay and soft soils. However, in the development of the rowe cell device, the results of lowering soft soil were better than the oedometer. The advantage of this rowe cell is that it can determine the saturation value of the soil samples tested. The rowe cell tester can measure the pore water pressure at the beginning and end of each consolidation stage. This rowe cell can provide suitable settlement for soft soils. This consolidation test to obtain soil parameters such as Cv and Cc by using the rowe cell tool. After that, from the test results, the two tools were compared.

Geosynthetic Encased Column: comparison between numerical and experimental results

2021 ◽  
Vol 44 (4) ◽  
pp. 1-12
Author(s):  
Nima Alkhorshid ◽  
Gregório Araújo ◽  
Ennio Palmeira
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Ground Improvement ◽  
Soft Soil ◽  
Experimental Tests ◽  
High Permeability ◽  
Soft Soils ◽  
Column Comparison ◽  
Surrounding Soil ◽  
Granular Column

The use of granular column is one of the ground improvement methods used for soft soils. This method improves the foundation soils mechanical properties by displacing the soft soil with the compacted granular columns. The columns have high permeability that can accelerate the excess pore water pressure produced in soft soils and increase the undrained shear strength. When it comes to very soft soils, the use of granular columns is not of interest since these soils present no significant confinement to the columns. Here comes the encased columns that receive the confinement from the encasement materials. In this study, the influence of the column installation method on the surrounding soil and the encasement effect on the granular column performance were investigated using numerical analyses and experimental tests. The results show that numerical simulations can reasonably predict the behavior of both the encased column and the surrounding soil.

scholarly journals Numerical Modelling of Prefabricated Vertical Drain for Soft Clay Using ABAQUS

2015 ◽  
Vol 773-774 ◽  
pp. 1502-1507
Author(s):  
Saiful Azhar Ahmad Tajudin ◽  
Mohd Fairus Yusof ◽  
I. Bakar ◽  
Aminaton Marto ◽  
Muhammad Nizam Zakaria ◽  
...  
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Soft Clay ◽  
Elastic Model ◽  
Clay Layer ◽  
Soil Consolidation ◽  
Consolidation Process ◽  
Vertical Drain ◽  
Prefabricated Vertical Drain

Construction, buildings and infrastructure founded on soft clays are often affected by settlement problem. Therefore, Prefabricated Vertical Drain (PVD) is one of the best solutions to accelerate soil consolidation by shortening the drainage path. In this study, numerical investigation was carried out to pursue a better understanding of the consolidation behavior of soft clay improved with PVD. The consolidation process accelerated by PVD with surcharge of 50 kPa was analysed using the ABAQUS software by adopting an elastic model. The aim of this study is to compare the settlement and the required time to fully consolidate the soft soil at different drain spacings (1.0 m, 1.5 m and 2.0 m) for two different thickness of the clay layer. The results shows that the time required to completely consolidate the soft soil for 12 m and 20 m thickness of clay layer with different spacings are in the range of 3 months to 66 months. The settlement rate and excess pore water pressure dissipation are increased when the spacing of the drain closer.

scholarly journals Physical Model Test for Soft Soil With or Without Prefabricated Vertical Drain with Loading

2018 ◽  
Vol 4 (8) ◽  
pp. 1809
Author(s):  
Dao Huu Do ◽  
Nguyen Thi Phuong Khue ◽  
Phan Khac Hai
Keyword(s):  
Numerical Simulation ◽  
Physical Model ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Physical Model Test ◽  
Soil Parameters ◽  
Vertical Drain ◽  
Prefabricated Vertical Drain ◽  
Before And After

The paper builds a physical model of testing in the laboratory with the parametric tempered glass box 0.5  0.5 1.2 m (length  width  depth) containing saturated clay to study the settlement and consolidation when loading increased gradually over time. The research covers herein to present the monitoring of settlement and pore water pressure, settlement calculation, numerical simulation using PLAXIS software V8.2 based on the results of soil physical and mechanical tests before and after loading in case of having or not prefabricated vertical drain (PVD). In case of no PVD, the calculation and numerical simulation using the soil parameters before loading have the differential settlement from the monitoring data, approximately 3.86 mm (10.45%), 0.41 mm (1.11%) respectively. Meanwhile, the deviation in the case using data after loading is about 2.29 mm (6.20%), 0.21 mm (0.56%) respectively. In case of PVD, the calculation and numerical simulation with the testing result of before loading deviation from the settlement monitoring by subsidence meter is 2.91 mm (7.88%), 44.42 mm (120.28%), calculation and simulation with the testing result of after loading deviation is 0.80 mm (2.17%), 1.26 mm (3.41%). In the case of having PVD, the difference in calculation, subsidence observation, and numerical simulation between the mechanical properties before and after loading is significant, when using the mechanical data after loading then the results are quite close to the subsidence of observation and simulation rather than before loading. 

scholarly journals Mechanical behaviour of calcareous waste under consolidated drained triaxial compression testing in saturated conditions

2019 ◽  
Vol 106 ◽  
pp. 01016
Author(s):  
Jakub Zięba
Keyword(s):  
Mechanical Behaviour ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Soil Samples ◽  
Excess Pore Water Pressure ◽  
Stiffness Properties ◽  
Construction Purpose ◽  
Strength And Stiffness ◽  
Excess Pore

The article presents the mechanical behaviour of calcareous waste under consolidated and drained condition in Triaxial compression test (CD). The host material currently being considered for the construction purpose of several buildings in Poland. One of the location of calcareous waste is in Łagiewniki area (in Cracow) [1,2]. In this work, particular attention has been paid to the to ensure fully saturation for all the tested soil samples and avoid generation of unwanted excess pore water pressure during shearing stage. The saturation level of soil samples was estimated based on Skempton’s law (B>0.95). CD Triaxial test have been conducted in order to derive information on its strength and stiffness properties.

Study on Artificial Island Ground Improvement Method and Effect

2014 ◽  
Vol 1030-1032 ◽  
pp. 1037-1040
Author(s):  
Jin Fang Hou ◽  
Ju Chen ◽  
Jian Yu
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Ground Improvement ◽  
Soft Soil ◽  
Horizontal Displacement ◽  
Treatment Method ◽  
Surcharge Preloading ◽  
Porosity Ratio ◽  
Improvement Method ◽  
Consolidation Degree

The artificial island ground on an open sea is covered by thick soft soil. It must be improved before using. In accordance with a designing scheme, the ground treatment method is inserting drain boards on land and jointed dewatering surcharge preloading, the residual settlement is not more than 30cm after improvement and the average consolidation degree is more than 85%. In order to estimate ground improvement effect and construction safety, instruments are buried to monitor the whole ground improving processes. By monitoring settlement and pore water pressure, it is shown that the total ground settlement in construction is 2234mm, its final settlement is 2464mm, and consolidation degree and residual settlement respectively satisfy requirements. In ground improvement, horizontal displacement is small and construction is safe. Meanwhile, the results of soil properties and vane shear strength detection tests show the soft soil ground is greatly reduced in water content and porosity ratio, and improved in strength. It is named that the ground improvement method is reasonable and reaches expected effect.

Applied Research on Dynamic Replacement Method in Tailings Residue Subgrade Reinforcement

2013 ◽  
Vol 639-640 ◽  
pp. 943-946
Author(s):  
Jiao Long He ◽  
Yong Zhou ◽  
Zhong Ai Jiang
Keyword(s):  
Applied Research ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Field Testing ◽  
Standard Penetration Test ◽  
Load Test ◽  
Test Results ◽  
Replacement Method ◽  
Dynamic Replacement ◽  
Testing Experiment

Based on the reinforcing mechanism of dynamic replacement method ,this article put forward the construction parameters and measures of dynamic replacement method , combining with the result of actual engineering field testing experiment. The field load test, standard penetration test and pore water pressure test results show that the characteristic value of subgrade bearing capacity is more than 130 kpa when the tailings residue subgrade has been managed with dynamic replacement method, providing references for applied research on dynamic replacement method in tailings residue subgrade reinforcement.

scholarly journals Impact of the moisture content in medium sands on CPTU test results

2016 ◽  
Vol 48 (3) ◽  
pp. 221-231 ◽  
Author(s):  
Łukasz Zawadzki ◽  
Marek Bajda
Keyword(s):  
Moisture Content ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Degree Of Saturation ◽  
Test Results ◽  
Time Dynamic ◽  
Tip Resistance ◽  
The Impact ◽  
Resistance Value

Abstract Soils occurring in the soil “active zone” are in contact with the surface and are directly influenced by external factors (mainly climatic changes) that cause variation in their parameters over time. Dynamic and uncontrolled changes of soil properties e.g. due to rainfall and evapotranspiration processes may affect field test results leading to the misinterpretation of the obtained data. This paper presents investigations on the influence of moisture content changes in sandy soils on CPTU results. For this purpose, a field ground model has been constructed and five CPTU tests with a different moisture content of soil were carried out. During the investigations, the tip resistance (qc), friction on sleeve (fs), and pore water pressure (u2) were measured. Moreover, a TDR probe was applied to determine the distribution of the moisture content in the studied soil columns. Differences between CPT results obtained in saturated and unsaturated soils have been shown. Furthermore, a simple equation to correct the tip resistance value due to the impact of the degree of saturation has been proposed.

Improving engineering properties of mature fine tailings using Tubifex

2020 ◽  
Vol 47 (7) ◽  
pp. 812-821
Author(s):  
Xiaojuan Yang ◽  
Miguel de Lucas Pardo ◽  
Maria Ibanez ◽  
Lijun Deng ◽  
Luca Sittoni ◽  
...  
Keyword(s):  
Survival Rate ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Engineering Properties ◽  
Test Results ◽  
Sulfate Content ◽  
Mature Fine Tailings ◽  
Fine Tailings ◽  
The Mean ◽  
Solids Content

The present study investigated the effects of Tubifex (Oligochaeta: Tubificidae) treatment on the dewatering process of mature fine tailings (MFT). Experiments testing the survival rate showed that Tubifex can survive at 20 °C and 4 °C. MFT with initial solids content (Sc) of 30% of total mass were treated in 11 settling columns by three Tubifex densities, 1400, 2000 and 4200 individuals·m−2. Test results showed that the mean survival rate at 20 °C and 4 °C on the 28th day stayed around 85%. Tubifex enhanced MFT dewatering by providing compacted tailings with 11.6% and 66.7% higher Sc and undrained shear strength compared with nontreated tailings. Tubifex accelerated pore water pressure dissipation. Tubifex did not affect the chemical composition of tailings except for a decrease in sulfate content. The Sc of tailings treated by Tubifex increased by 67.4% within nine months, which was 129% greater than the Sc increase of the nontreated tailings after 11 months.

scholarly journals Experimental Study on the Variation Law of Excess Pore Water Pressure at the Bottom of the Foundation Pit for Excavation

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Qizhi Hu ◽  
Qiang Zou ◽  
Zhigang Ding ◽  
Zhaodong Xu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Confining Pressure ◽  
Deep Foundation ◽  
Foundation Pit ◽  
Excess Pore Water Pressure ◽  
Accurate Expression ◽  
Excess Pore

The excavation unloading of deep foundation pits in soft soil areas often produces negative excess pore water pressure. The rebound deformation of soil on the excavation surface of the foundation pit can be predicted reliably through the accurate expression of relevant variation laws. In combination with the principle of effective stress and the general equation of unidirectional seepage consolidation, an equation for calculating the rebound deformation from the bottom in the process of foundation pit excavation unloading was obtained. Additionally, a triaxial unloading test was adopted to simulate the excavation unloading processes for actual foundation pit engineering. After studying the variation law of the excess pore water pressure generated by excavation unloading, it was found that the negative excess pore water pressure increased with increasing unloading rate, while the corresponding peak value decreased with increasing confining pressure. The equation for rebound calculation was verified through a comparison with relevant measured data from actual engineering. Therefore, it is considered that the equation can reliably describe the rebound deformation law of the base. This paper aims to guide the design and construction of deep foundation pits in soft soil areas.

scholarly journals Experiment Study of Lateral Unloading Stress Path and Excess Pore Water Pressure on Creep Behavior of Soft Soil

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Wei Huang ◽  
Kejun Wen ◽  
Dongsheng Li ◽  
Xiaojia Deng ◽  
Lin Li ◽  
...  
Keyword(s):  
Pore Water ◽  
Creep Behavior ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Stress Path ◽  
Deviatoric Stress ◽  
Excess Pore Water Pressure ◽  
Pore Water Pressures ◽  
Excess Pore

The unloading creep behavior of soft soil under lateral unloading stress path and excess pore water pressure is the core problem of time-dependent analysis of surrounding rock deformation under excavation of soft soil. The soft soil in Shenzhen, China, was selected in this study. The triaxial unloading creep tests of soft soil under different initial excess pore water pressures (0, 20, 40, and 60 kPa) were conducted with the K0 consolidation and lateral unloading stress paths. The results show that the unloading creep of soft soil was divided into three stages: attenuation creep, constant velocity creep, and accelerated creep. The duration of creep failure is approximately 5 to 30 mins. The unloading creep behavior of soft soil is significantly affected by the deviatoric stress and time. The nonlinearity of unloading creep of soft soil is gradually enhanced with the increase of the deviatoric stress and time. The initial excess pore water pressure has an obvious weakening effect on the unloading creep of soft soil. Under the same deviatoric stress, the unloading creep of soft soil is more significant with the increase of initial excess pore water pressure. Under undrained conditions, the excess pore water pressure generally decreases during the lateral unloading process and drops sharply at the moment of unloading creep damage. The pore water pressure coefficients during the unloading process were 0.73–1.16, 0.26–1.08, and 0.35–0.96, respectively, corresponding to the initial excess pore water pressures of 20, 40, and 60 kPa.

Sign in / Sign up

Export Citation Format

Share Document