scholarly journals Characteristic of Coconut-Shell Ash as Filler and LDPE Plastic Waste as Substitution Materials of Porous Asphalt Mixtures

2019 ◽  
Vol 8 (3S3) ◽  
pp. 340-344
Keyword(s):  
Asphalt Mixture ◽  
Plastic Waste ◽  
Asphalt Mixtures ◽  
Coconut Shell ◽  
Fine Aggregate ◽  
Porous Asphalt ◽  
Bitumen Content ◽  
Coconut Shell Ash ◽  
Pavement Structures ◽  
Marshall Stability

Porous asphalt is designed to have a relatively higher porosity than other pavement types, this porous property is obtained because the proportion of fine aggregate is less than other types of mixtures. In an effort to increase the strength of porous asphalt pavement structures, it is required to use other added materials both as additives, stabilizers and substitution materials. In this study, the added material used was low density polyethylene (LDPE) plastic waste as a substitute for asphalt and coconut-shell ash (CA) as filler substitution material. Stone ash, cement and fly ash are commonly used as fillers in asphalt mixture, CA is expected to be one of the alternatives. This study aims to determine the characteristics of using LDPE into asphalt pen. 60/70 and the use of 50% CA filler on the characteristics of porous asphalt mixture and to find out indications of deficiencies and strengths in the asphalt mixture. On the initial bitumen content without using substitutes, the optimum bitumen content (OAC) was 5.76% with the variation used of LDPE 3%, 5% and 7% and 50% CA as filler. At OAC value 5.76% with 3% LDPE substitution meet all required parameter. With the value of Marshall Stability, VIM, Flow, AFD, and CL are 560.50kg, 18.61%, 4.3mm, 0.22% and 19.69% respectively.

scholarly journals Performance of Charcoal Coconut Shell Ash in the Asphalt Mixture under Long Term Aging

2019 ◽  
Vol 8 (3S3) ◽  
pp. 383-387
Keyword(s):  
Resilient Modulus ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Coconut Shell ◽  
The Road ◽  
Dynamic Creep ◽  
Coconut Shell Ash ◽  
The Stability ◽  
Marshall Stability

Improvement in transportation system is never been as easy as just providing links for better connection and network but more to do with the pavement quality of the road itself. Modification with agriculture waste is just another approach to enhance the performance of asphaltic concrete. In this study, a non-traditional bitumen modifier from a coconut shell which is the charcoal coconut shell ash (CCSA) was used. Addition of CCSA in bitumen with 0%, 2%, 4%, 6%, and 8% by weight of bitumen were investigated along with the laboratory stimulation of aging was applied in this study. Properties of modified asphalt mixture were determined using resilient modulus, dynamic creep and Marshall Stability test.. Results of samples with CCSA which underwent aging show some improvement in terms of the stability and permanent deformation characteristics. Resilient modulus, dynamic creep and Marshall Stability tests recorded the highest rates when compared to controlled sample. Hence, for more durable asphalt concrete and high serviceability it is recommended to use 2% to 4% of CCSA.

Effects of Crushed Glass Waste as a Fine Aggregate on Properties of Hot Asphalt Mixture

2021 ◽  
Vol 28 (3) ◽  
pp. 129-145
Author(s):  
Ahmed Almuhmdi ◽  
 Abdulbasit Muhmood ◽  
Abdulhakim Salih
Keyword(s):  
Tensile Strength ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Partial Substitution ◽  
Fine Aggregate ◽  
Glass Waste ◽  
Air Voids ◽  
Binder Layer ◽  
Indirect Tensile ◽  
Marshall Stability

The recycling of waste requires large areas; besides recycling wastes to their origin is often economically and environmentally costly. Glass is considered as a solid waste that is difficult to dispose of; it doesn't degrade nor burn. Since glass is a silicic substance with similar properties to aggregates, it can be recycled in asphalt mixtures. This research aims to determine optimum binder content (OBC) of conventional hot asphalt mixture (HMA), (control mixture), and investigate the effect of crushed glass waste (CGW), on its properties. In this work, several percentages of CGW (10%, 15%, 20%, and 25%) have been used as a partial substitution for the weight of fraction size 2.36-0.075mm of natural aggregate to prepare glass-contained asphalt mixtures and compare their properties with the control mixture. Mix design by Marshall method was used, and the properties according to Iraqi standards (SORB/R9,2003), for binder layer, were found, as well as conducting of Retained Marshall stability (RMS), indirect tensile strength (IDT), and tensile strength ratio (TSR), tests on mixtures, as performance tests. The results showed that the OBC of the control mixture was 5% wt., and the Marshall stability and flow values of glass-contained asphalt mixtures were oscillating around the values of the control mixture. The air voids, voids in mineral aggregate, and bulk density were reduced regularly as CGW increased. Also, it was observed from the results that the glass-contained mixtures have good performance properties. However, all results conformed to the standards (SORB/R9, 2003). So, the incorporation of CGW in HMA for the binder layer is feasible.

Performance Characterization of Stone Mastic Asphalt using Steel Fiber

2021 ◽  
Vol 02 (02) ◽  
Author(s):  
Ekarizan Shaffie ◽  
◽  
H.A. Rashid ◽  
Fiona Shiong ◽  
Ahmad Kamil Arshad ◽  
...  
Keyword(s):  
Steel Fiber ◽  
Mechanical Performance ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Moisture Susceptibility ◽  
Mastic Asphalt ◽  
Bitumen Content ◽  
Stone Mastic Asphalt ◽  
The Stability ◽  
Marshall Stability

Stone Mastic Asphalt (SMA) is a gap-graded hot mixture designed to provide higher resistance towards permanent deformation and rutting potential by 30% to 40% more than dense-graded asphalt, due to its stable aggregate skeleton structure. However, compared to other types of hot mix asphalt, SMA unfortunately has some shortcomings in term of its susceptibility towards moisture-induced damage due to its structure and excessive bitumen content in the composition. This research aims to assess the performance of a SMA mixture with steel fiber by enhancing overall stability, abrasion resistance, and, most importantly, moisture susceptibility. This study involved the incorporation of various steel fiber proportions of 0%, 0.3%, 0.5% and 0.7% by the total weight of mixture. The steel fiber modified SMA was made up of 6.0% PEN 60/70 bitumen content. The performance of SMA were evaluated through Marshall stability and flow test, Cantabro loss test and indirect tensile strength test. The results obtained from the testing showed that the incorporation of steel fiber is significantly effective to enhance the resistance towards moisture damage, while increasing the stability and reducing the abrasion loss of SMA mixture, compared to conventional mixture. Overall, it can be concluded that the addition of steel fiber in asphalt mixture specifically SMA, has improved the mechanical performance in the application of asphalt pavement with the optimum steel fiber proportion of 0.3% by the weight of mixture. The developed models between the independent variables and responses demonstrated high levels of correlation. The study found that Response Surface Methodology (RSM) is an effective statistical method for providing an appropriate empirical model for relating parameters and predicting the optimum performance of an asphaltic mixture to reduce flexible pavement failure.

Determining Optimum Carbon Nanotubes Content for Asphalt Mixture in Road Pavements

2021 ◽  
Vol 1023 ◽  
pp. 121-126
Author(s):  
Van Bach Le ◽  
Van Phuc Le
Keyword(s):  
Carbon Nanotubes ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Construction Cost ◽  
Asphalt Mixtures ◽  
Static Modulus ◽  
Pavement Construction ◽  
Modified Binder ◽  
Marshall Stability

Although small amount of binder in asphalt concrete mixture may commonly range from 3.5 to 5.5% of total mixture as per many international specifications, it has a significant impact on the total cost of pavement construction. Therefore, this paper investigated the effects of five carbon nanotubes contents of 0.05%, 0.1%, 0.15%, 0.2%, 0.25% by asphalt weight as an additive material for binder on performance characteristics of asphalt mixtures. Performance properties of CNTs modified asphalt mixtures were investigated through the Marshall stability (MS) test, indirect tensile (IDT) test, static modulus (SM) test, wheel tracking (WT) test. The results indicated that asphalt mixtures with CNT modified binder can improve both the rutting performance, IDT strength and marshall stability of tested asphalt mixtures significantly at higher percentages of carbon nanotubes. However, the issue that should be considered is the construction cost of asphalt pavement. Based on the asphalt pavement structural analysis and construction cost, it can be concluded that an optimum CNT content of 0.1% by asphalt weight may be used as additive for asphalt binder in asphalt mixtures.

scholarly journals Laboratory Evaluation of the Use of Florida Washed Shell in Open-Graded Asphalt Mixtures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7060
Author(s):  
Mohammad Alharthai ◽  
Qing Lu ◽  
Ahmed Elnihum ◽  
Asad Elmagarhe
Keyword(s):  
Tensile Strength ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Laboratory Evaluation ◽  
Void Content ◽  
Coarse Aggregates ◽  
Significant Difference ◽  
Indirect Tensile ◽  
Marshall Stability

This study investigates the substitution of conventional aggregate with a Florida washed shell in open-graded asphalt mixtures and evaluates the optimal substitution percentage in aggregate gradations of various nominal maximum aggregate sizes (NMASs) (i.e., 4.75, 9.5, and 12.5 mm). Laboratory experiments were performed on open-graded asphalt mixture specimens with the coarse aggregate of sizes between 2.36 and 12.5 mm being replaced by the Florida washed shell at various percentages (0, 15, 30, 45, and 100%). Specimen properties relevant to the performance of open-graded asphalt mixtures in the field were tested, evaluated, and compared. Specifically, a Marshall stability test, Cantabro test, indirect tensile strength test, air void content test, and permeability test were conducted to evaluate the strength, resistance to raveling, cracking resistance, void content, and permeability of open-graded asphalt mixtures. The results show that there is no significant difference in the Marshall stability and indirect tensile strength when the coarse aggregates are replaced with Florida washed shell. This study also found that the optimum percentages of Florida washed shell in open-graded asphalt mixture were 15, 30, and 45% for 12.5, 9.5, and 4.75 mm NMAS gradations, respectively.

LABORATORY EVALUATION ON THE EFFECT OF CLOGGING ON PERMEABILITY OF POROUS ASPHALT MIXTURES

2015 ◽  
Vol 76 (14) ◽  
Author(s):  
Norhidayah Abdul Hassan ◽  
Nor Asniza Mohamed Abdullah ◽  
Nurul Athma Mohd Shukry ◽  
Mohd Zul Hanif Mahmud ◽  
Nur Zurairahetty Mohd Yunus ◽  
...  
Keyword(s):  
Asphalt Mixture ◽  
Residential Area ◽  
Liquid Limit ◽  
Asphalt Mixtures ◽  
Public Works ◽  
Storm Water ◽  
Laboratory Evaluation ◽  
Aggregate Gradation ◽  
Porous Asphalt ◽  
The One

Porous asphalt mixture is one of the alternative solutions to increase pervious surface area due to urbanization. The uniqueness of porous asphalt surface textures and internal structures allows the mixture to become a temporary storm-water retention and capable to channel excessive storm water. However, one of the major problems that affect the performance of porous asphalt mixtures is the clogging. Therefore, this study aims to determine the effect of clogging towards the permeability of porous asphalt. A total of 30 gyratory compacted samples were fabricated according to aggregate gradation recommended by Malaysia Public Works Department. The clogging materials were collected from two different location, residential area and major highway. The composition and characteristics of the clogging materials were investigated using Plastic Limit, Liquid Limit and Scanning Electron Microscope (SEM). The permeability test was conducted to investigate the permeability rate of the compacted samples based on different clogging material types, clogging concentrations and clogging cycles. In addition, the compacted samples were scanned using X-ray Computed Tomography to obtain the air voids distribution throughout the samples for comparison. It was found that higher concentration of clogging materials and clogging cycles reduced the rate of permeability. Clogging material collected from residential area has higher tendency to clog the void spaces compared to the one obtained from highway.

scholarly journals Performance and Durability of Porous Asphalt Mixtures Manufactured Exclusively with Electric Steel Slags

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3306 ◽  
Author(s):  
Marta Skaf ◽  
Emiliano Pasquini ◽  
Víctor Revilla-Cuesta ◽  
Vanesa Ortega-López
Keyword(s):  
Mechanical Performance ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Electric Steelmaking ◽  
Porous Asphalt ◽  
Bituminous Mixtures ◽  
Abrasion Loss ◽  
Water Sensitivity ◽  
Electric Arc Furnace Slag ◽  
Furnace Slag

Electric arc furnace slag (EAFS) and ladle furnace slag (LFS) are by-products of the electric steelmaking sector with suitable properties for use in bituminous mixtures as both coarse and fine aggregates, respectively. In this research, the production of a porous asphalt mixture with an aggregate skeleton consisting exclusively of electric steelmaking slags (using neither natural aggregates nor fillers) is explored. The test program examines the asphalt mixtures in terms of their mechanical performance (abrasion loss and indirect tensile strength), durability (cold abrasion loss, aging, and long-term behavior), water sensitivity, skid and rutting resistance, and permeability. The results of the slag-mixes are compared with a standard mix, manufactured with siliceous aggregates and cement as filler. The porous mixes manufactured with the slags provided similar results to the conventional standard mixtures. Some issues were noted in relation to compaction difficulties and the higher void contents of the slag mixtures, which reduced their resistance to raveling. Other features linked to permeability and skid resistance were largely improved, suggesting that these mixtures are especially suitable for permeable pavements in rainy regions. In conclusion, a porous asphalt mixture was produced with 100% slag aggregates that met current standards for long-lasting and environmentally friendly mixtures.

Laboratory Investigate of the Effect of Fine Aggregates on Asphalt Mixture Materials

2011 ◽  
Vol 225-226 ◽  
pp. 577-580
Author(s):  
Yong Ye ◽  
Yi Zhou Cai
Keyword(s):  
Compressive Strength ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Fine Aggregate ◽  
Test Results ◽  
Creep Tests ◽  
Aggregate Gradation ◽  
Static Creep ◽  
Fine Aggregates

The objective of this study is to investigate and evaluate the effect of fine aggregates (aggregate size smaller than or equal to 2.36 mm) on the compressive strength and creep behavior of asphalt mixtures. The variables that are considered in the study include the sizes and gradations of fine aggregate. A kind of standant aggregate gradation and four kinds of reduced aggregate gradation mixture specimens are used. Uniaxial compression and static creep tests were realized at different loading conditions. The test results showed that the different fine aggregate sizes do not result in significant differences in compressive strength and creep values using the same percentage of fine aggregates (38.4%). Only the different gradations showed a little differences for mixtures made with different gradations but same aggregate size (between 2.36 and 1.18 mm).

scholarly journals Pengaruh Serbuk Ban Bekas Sebagai Campuran Agregat Halus Pada Campuran Aspal Porous

2019 ◽  
Vol 24 (2) ◽  
pp. 144
Author(s):  
Nunung Martina ◽  
Muhammad Fathur Rouf Hasan ◽  
Yanuar Setiawan
Keyword(s):  
Asphalt Mixture ◽  
Flexible Pavement ◽  
Environmental Problems ◽  
Fine Aggregate ◽  
Construction Work ◽  
Porous Asphalt ◽  
Road Pavement ◽  
Alternative Materials ◽  
Pavement Construction ◽  
New Generation

The porous asphalt mixture is a new generation of flexible pavement that is able to pass water in the upper layer (wearing course) both vertically and horizontally. The porous asphalt layer effectively provides more safety, especially when it rains to avoid aquaplaning which causes roughness of the surface to be more rough. Therefore, at this time there are many studies on the use of alternative materials to replace the limited natural materials with materials that can be utilized. The results showed that porous asphalt mixture with used tire crumb as a fine aggregate mixture had an increase in flow value of 6.32% with a decrease in stability value by 27.52% and a decrease Marshall Quotient value at 31.82%. The testing of roughness is increased by 17.71% and Mu-Meter 24.14%. This research is effective in overcoming environmental problems which include processing tire waste of 3.03 tons for 1 km of road pavement construction work.

Sign in / Sign up

Export Citation Format

Share Document