scholarly journals Effect of Feeding Technique in Mechanical Behaviour of Sic/Tio2 Reinforced AA 6082 Composites

2019 ◽  
Vol 8 (3) ◽  
pp. 8233-8236
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stir Casting ◽  
Homogeneous Distribution ◽  
Micro Hardness ◽  
Casting Technique ◽  
Feeding Technique ◽  
Normal Feeding ◽  
Feeding Process ◽  
Effect Of Feeding

In this study, SiC and TiO2 nanoparticles reinforced AA 6082 composites were prepared by stir casting technique. The optimized quantities of reinforcement particles used in composites was 6 Wt.%. The mechanical properties such as tensile strength, compressive strength and hardness of prepared composites were improved significantly about with novel multi-encapsulate feeding as compared normal feeding technique. Also, the drastic improvement was noted with microstructure in order to form of health clusters and homogeneous distribution under novel feeding than normal feeding. The testing shows that the micro hardness and tensile strength was improved about 10% and 5% than normal feed process. Lesser blow holes and good matrix materials dispersion was found in multi encapsulate feeding process. From this experimentation, it was confirmed that multiple encapsulate feeding of reinforcement particles can increase the mechanical strength and microstructure properties than normal feed technique.

scholarly journals Microstructure, Tensile Properties and Hardness Behavior of Al7075 Matrix Composites Reinforced With Graphene Nanoplatelets and Beryl Fabricated by Stir Casting Method

2019 ◽  
Vol 9 (1) ◽  
pp. 6761-6765 ◽  
Keyword(s):  
Tensile Strength ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Matrix Material ◽  
Stir Casting ◽  
Hybrid Nanocomposites ◽  
Homogeneous Distribution ◽  
Casting Technique ◽  
Aluminum 7075 ◽  
Scanning Electron

In this research, an effort is made to familiarize and best potentials of the reinforcing agent in aluminum 7075 matrices with naturally occurring Beryl (Be) and Graphene (Gr) to develop a new hybrid composite material. A stir casting technique was adopted to synthesize the hybrid nanocomposites. GNPS were added in volume fractions of 0.5wt%, 1wt%, 1.5wt%, and 2wt% and with a fixed volume fraction of 6 wt.% of Beryl. As cast hybrid composites were microstructurally characterized with scanning electron microscopy and X-ray diffraction. Microstructure study through scanning electron microscope demonstrated that the homogeneous distribution reinforcement Beryl and GNPs into the Al7075 matrix. Brinell hardness and tensile strength of synthesized materials were investigated. The hybrid Al7075-Beryl-GNPs composites showed better mechanical properties compared with base Al7075 matrix material. The ascast Al7075-6wt.% Beryl-2wt.%GNPs showed 49.41% improvement in hardness and 77.09% enhancement in ultimate tensile strength over Al7075 alloy.

scholarly journals Study on Properties of Multi Walled Carbon Nanotube Reinforced Aluminum Matrix Composite through Casting Technique

2021 ◽  
Vol 18 (1) ◽  
pp. 97-101
Author(s):  
Shuib Pasha S A ◽  
Nayeem Ahmed M ◽  
Tilak S R ◽  
Anil Kumar B N
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Matrix Composite ◽  
Research Work ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Optical Microscope ◽  
Aluminum Matrix Composite ◽  
Casting Technique ◽  
Multi Walled Carbon Nanotubes

Composite materials are defined as material systems consisting of mixture of or combination of two or more micro constituents insoluble in each other and differing in form and or material composition. In this study Metal Matrix Composite (MMCs) has been produced using stir casting method for performing the mechanical properties. Most of the engineering industries want light and better mechanical properties of components; this can be achieved by MMCs of Aluminium because of its excellent performance. In this research work we fabricate the Aluminium by liquid route. Here Al 7075 is used as a base metal and Multi Walled Carbon Nanotubes (MWCNT) used as sub metal with various percentages. Experiments were conducted to analyze microstructure, hardness & tensile strength. By using optical microscope and Scanning Electron Microscope (SEM) we analyze the sample specimens are well dispersion in MWCNT with AA 7075. Hardness and tensile strength increases with increasing of wt. %. Hardness of material increases with increase in percentages of MWCNT, whereas tensile strength of the material increases with increase in percentages of MWCNT and Elongation reduces

Effect of Aging Treatment on Microstructure and Mechanical Properties of Al-Si Matrix Alloy Reinforced with High Purity Aluminum Nitride (AlN)

2011 ◽  
Vol 462-463 ◽  
pp. 967-971
Author(s):  
Mahamad Noor Wahab ◽  
Mariyam Jameelah Ghazali ◽  
Abdul Razak Daud
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Nitride ◽  
High Purity ◽  
Aging Treatment ◽  
Matrix Alloy ◽  
Stir Casting ◽  
Weight Percentage ◽  
Casting Technique ◽  
Microstructure And Mechanical Properties

Microstructure and mechanical properties of heat treated Al-Si alloy containing up to 10 wt% aluminum nitride (AlN) particles were investigate. In this work high purity AlN powder with different weight percentage of 0, 5, 7 and 10 were calculated as reinforced material to the metal matrix composites. The Al-Si matrix was prepared by a bottom pour stir casting technique. Heat treatment was performed by soaking and followed by an aged treatment. It was found that the AlN particles were scattered randomly distributed in the matrix composite. Ageing induced Si grain transformation into to spheroid shapes while Al dendrites tend to become finer. Ultimate tensile strength (UTS) had improved drastically from to 125MPa to 306MPa for un-aged Al-Si alloy and aged AlN 7 wt%. Fracture morphologies showed a pronounced feature with small dimples, tear ridges and micro neck particularly in the aged samples leading to a higher tensile value and increase in ductility. The presence of AlN particles in the alloys had improved the tensile strength by slowing down the plastic deformation during tensile test.

Role of Nano-Sized Graphene Amine Reinforcements on Mechanical Properties of AA7076 Based MMCs

2020 ◽  
Vol 12 ◽  
Author(s):  
Nagaraj R. Banapurmath ◽  
Adarsh Patil ◽  
Anand M. Hunashyal ◽  
Vinodkumar V. Meti ◽  
Arun Y. Patil ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Structural Engineering ◽  
Matrix Material ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Stir Casting ◽  
Homogeneous Distribution ◽  
Weight Percentage ◽  
Casting Technique ◽  
Industry Needs

Aims: AA7076 is a well-defined alloy for its excellent physical and mechanical properties such as high strength, toughness, and low density. To reach the expectations of the automobile and aerospace industry needs, the properties of AA7076 alloy has to be improved by reinforcing nano-sized graphene amine particles. Objectives: Synthesis and characterization of the AA7076 alloy reinforced with graphene nanofillers for different structural engineering applications. Methods: In this present work, nano-sized graphene amine particles were added and dispersed homogeneously using a motorized stir casting technique. AA7076/graphene amine composites were prepared by varying wt.% percent of graphene amine reinforcement particles (0.5, 0.75, 1, and 1.25 wt.% (weight-percentage)). Results: The SEM micrographs reveal the homogeneous distribution of graphene amine reinforcements along the grain boundaries of the AA7076 matrix material. The experimental test results showed that the addition of graphene amine reinforcements, the mechanical properties of the AA7076/graphene amine composite, improved as compared to the AA7076 matrix material. Conclusion: The composite with 1 wt.% graphene amine showed higher strength and hardness as compared to other reinforcements.

Evaluation of Mechanical Properties of Aluminum Alloy (Al2024) Reinforced with Silicon Carbide (SiC) Metal Matrix Composites

2017 ◽  
Vol 263 ◽  
pp. 184-188 ◽  
Author(s):  
P. Subramanya Reddy ◽  
R. Kesavan ◽  
B. Vijaya Ramnath
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Base Alloy ◽  
Stir Casting ◽  
Matrix Composites ◽  
Alloy Matrix ◽  
Casting Technique ◽  
Sic Particles

The investigation of mechanical properties of silicon carbide (SiC) powders reinforced with aluminum alloy composites are recorded in this paper. SiC powders of approximately 35µm size were added in an aluminum alloy matrix to manufacture the samples of ratios 1, 2, 3 and 4 by weight % using the stir casting technique. The specimens were fabricated and several tests were conducted to evaluate the mechanical properties such as tensile strength, hardness and impact strength and then the values are compared with the base alloy. It has been observed from the results that the hardness, impact energy and tensile strength increases with the increase in % of SiC particles until 2% and drops on further increase in the SiC particles.

scholarly journals Microstructural and Mechanical Properties of AZ31B/Graphene Nanocomposite Produced by Stir Casting

2021 ◽  
Vol 31 (1) ◽  
pp. 51-56
Author(s):  
Ashish Kumar Srivastava ◽  
Ambuj Saxena ◽  
Nagendra Kumar Maurya ◽  
Shashi Prakash Dwivedi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Matrix Material ◽  
Microstructural Analysis ◽  
Stir Casting ◽  
Reinforcement Particle ◽  
Casting Technique ◽  
Reinforcement Material ◽  
The Matrix

In the current scenario, the development of high strength and low weight material is the demand of the aerospace defence organizations. Magnesium alloy based composite has low density, good mechanical and physical properties. In this study, magnesium alloy AZ31B is used as reinforcement material and graphene nanoparticle is used as reinforcement material. Stir casting technique is used for the development of composite material. Three weight percentages i.e. 0.4%, 0.8% and 1.2% are used for the casting. The microstructural analysis is performed to validate the presence of graphene particles in the developed composite. Further mechanical properties such as tensile strength, hardness and toughness are evaluated. Experimental results confirm that GNPs particles are uniformly distributed into the matrix material. It was observed that due to the reinforcement of GNPs particles tensile strength of the material is improved by 31.17%, hardness is improved about 46.9%. However, the peak value of toughness is observed 12.6 Jule/cm2 in the matrix material, it decreases by increasing the wt% of reinforcement particle and lowest value of toughness of 6.82 Jule/cm2 is observed in AZ31B/1.2%GNP composite.

scholarly journals Infuence of Pouring Temperature on Stir Casting of Al/SiC/Mg/Cu Composite

2021 ◽  
Author(s):  
Tamilanban Thangaraju ◽  
Ravikumar T S ◽  
Kanthasamy S
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stir Casting ◽  
Matrix Composites ◽  
Processing Parameter ◽  
Pouring Temperature ◽  
Casting Technique ◽  
Sic Particles ◽  
Metallurgical Characterization ◽  
6061 Aluminium Alloy

Abstract The effect of pouring temperature while preparing Aluminium SiC metal matrix composites, with additional benefits of magnesium and copper through stir casting technique were investigated. The composites were fabricated by mixing 12 wt% of SiC reinforcements,4 wt% magnesium and 2 wt% copper into 6061 aluminium alloy melt at different pouring temperatures (630 ºC, 670 ºC and 710ºC). The addition of magnesium will enhance the wettability of the SiC particles with Al matrix. The inclusion of copper has considerable improvement in strength and hardness of the composite. The microstructure and mechanical properties (tensile strength and hardness) of the Al MMC are evaluated with the corresponding processing parameter, specifically pouring temperature of the cast composite.The metallurgical characterization utilizing optical and scanning electron microscope were observed for the prepared composites. The coarse microstructure and homogenous distribution of SiC particles were appeared within dendrite structures of the composites. The SiC particles has effectively distributed, and higher tensile strength and maximum hardness have occurred in composite at pouring temperature of 670ºC as compared to other composites. The mechanical properties were lower in composites prepared using lesser pouring temperature (630ºC) and significantly decreased for higher pouring temperature (710ºC) of the composites.

scholarly journals ENHANCED MICROSTRUCTURE AND MECHANICAL PROPERTIES OF SiC PARTICLE REINFORCED ALUMINIUM ALLOY COMPOSITE MATERIALS

2019 ◽  
Vol 25 (4) ◽  
pp. 253 ◽  
Author(s):  
Manoj Kumar Pal ◽  
Arnav Vikram ◽  
Vineet Bajaj
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Tensile Strength ◽  
Aluminum Matrix ◽  
Hardness Test ◽  
Stir Casting ◽  
Homogeneous Distribution ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Sic Particles

<p class="AMSmaintext">Aluminium6061 alloy composites containing various volume fractions of Silicon Carbide (SiC) particles (0, 5%, 10%, 15%, 20% and 25%) were prepared by stir casting method. In the current study,<strong> </strong>microstructures and mechanical properties of cast silicon carbide (SiC) reinforced aluminum matrix composites (AMCs) were investigated. Optical microscopic examination, SEM, tensile strength test, hardness test and elongation test were carried out. The results showed that with the addition of SiC reinforcements in Aluminum6061 matrix increased hardness and tensile strength however, decreased elongation at 25% SiC reinforced AMC. Hardness and tensile strength were observed to be are maximum at 25% SiC and elongation is minimum at 25% SiC. Microstructural observation confirmed clustering and homogeneous distribution of SiC particles in the Al6061 matrix.</p>

Physical and mechanical properties of stir-casting processed AA2024/B4Cp composites

2014 ◽  
Vol 21 (4) ◽  
pp. 505-515 ◽  
Author(s):  
Aykut Canakci ◽  
Fazli Arslan ◽  
Temel Varol
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Tensile Strength ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Stir Casting ◽  
Particle Volume ◽  
Electron Microscopic ◽  
Particle Content ◽  
Casting Technique

AbstractIn this study, metal matrix composites of an aluminum alloy (AA2024) and B4C particles with volume fractions 3, 5, 7, and 10 vol% and with sizes 29 and 71 μm were produced using stir-casting technique. The effects of B4C particle content and size of boron carbide on the mechanical properties of the composites such as hardness, 0.2% yield strength, tensile strength, and fracture were investigated. Furthermore, the relation between particle content, microstructure, and particle distribution has been investigated. The hardness of the composites increased with increasing particle volume fraction and with decreasing particle size, although the tensile strength of the composites decreased with increasing particle volume fraction and with decreasing particle size. Scanning electron microscopic observations of the microstructures revealed that dispersion of the coarser sizes of B4C particles was more uniform while the finer particles led to agglomeration of the particles and porosity.

Effect of Cobalt content on mechanical properties of Al-Si alloy

2014 ◽  
Vol 2 (1) ◽  
pp. 46-58
Author(s):  
Maryam A. B.
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Wear Rate ◽  
Room Temperature ◽  
Cobalt Content ◽  
Stir Casting ◽  
Fish Bone ◽  
High Load ◽  
Micro Hardness ◽  
Casting Method

       This work encompasses studying the effect of different contents of Co on Al-Si alloy with Sb modification prepared by stir casting method. The content of Co is varying from 0 to 1.2wt%, The effect of Cobalt on microstructure, micro hardness, tensile strength and wear rate were studied extensively. The results show that the intermetallic compounds was increased with the increasing of Cobalt content .The Co-bearing compounds presented as small block shape at first and gradually turned into dendrite or fish bone shape. The addition of Co has appositive effect on tensile strength of the Al-Si alloys that used in the current research, the maximum tensile strength was (177MPa) when Co content was 0.9%Co at room temperature as well as wear rate were studied in this paper and noticed that the addition at 0.9%Co had the better effect at low and high load(5N),(10N).

Sign in / Sign up

Export Citation Format

Share Document