scholarly journals Load characteristics of three-plunger pumps for spray seawater fire-fighting

2020 ◽  
pp. 142-146
Author(s):  
В.А. Наумов ◽  
Н.Л. Великанов ◽  
А.В. Тришина
Keyword(s):  
Satisfactory Agreement ◽  
Test Data ◽  
High Efficiency ◽  
Measurement Data ◽  
Fire Fighting ◽  
Test Results ◽  
Hydraulic Characteristics ◽  
Fire Extinguishing ◽  
Load Characteristics ◽  
Low Pressures

Цель статьи – получить эмпирические зависимости для характеристик трехплунжерных противопожарных насосов (ТПН), необходимые для автоматизации расчетов систем тушения пожаров на судах с применением распыленной морской воды. Задачи исследования: проверка непротиворечивости данных испытаний; определение расчетных зависимостей производительности ТПН, к.п.д., затраченной мощности от давления. Проведенный анализ результатов испытаний ТПН подтвердил возможность использования предложенных зависимостей в инженерных расчетах. Данные измерений удовлетворительно согласуются с результатами расчетов, за исключением к.п.д. Отклонение экспериментальных точек от эмпирических зависимостей, скорее всего, связано с занижением значений затраченной мощности на испытаниях при небольших давлениях. Предложено для оценки к.п.д. использовать ранее полученную типовую зависимость. Построены графики для характеристик насоса NP25/41-170S. Пример расчета рабочей точки насосной установки с использованием приближенной гидравлической характеристики водяной пожарной системы судна показал высокую эффективность предложенных методик. The purpose of the article is to obtain empirical dependences for the characteristics of three-plunger fire-fighting pumps (TFP), which are necessary for automating calculations of fire extinguishing systems on ships using sprayed seawater. Research objectives: checking the consistency of test data; determining the calculated dependences of the TFP performance, efficiency, power expended on pressure. The analysis of the TFP test results confirmed the possibility of using the proposed dependencies in engineering calculations. The measurement data are in satisfactory agreement with the results of calculations, with the exception of efficiency. The deviation of experimental points from the empirical dependences is most likely due to an underestimation of the power consumed during tests at low pressures. It is proposed to use the previously obtained typical dependence to estimate the efficiency. Graphs are plotted for the characteristics of the NP25/41-170S pump. An example of calculating the working point of a pumping unit using the approximate hydraulic characteristics of the ship's water fire system showed the high efficiency of the proposed methods.

scholarly journals Hydraulic calculation of the fire extinguishing system of port facilities

2021 ◽  
pp. 141-145
Author(s):  
В.А. Наумов ◽  
Н.Л. Великанов ◽  
А.В. Тришина
Keyword(s):  
Hydraulic Calculation ◽  
Test Results ◽  
Reactive Force ◽  
Hydraulic Characteristics ◽  
Calculation Algorithm ◽  
Pump Operation ◽  
Fire Extinguishing ◽  
Port Facilities ◽  
Performance Research ◽  
Fire Extinguishing System

Цель статьи – разработать алгоритм расчёта гидравлических характеристик системы пожаротушения для портовых сооружений. В системе пожаротушения имеется погружной насос, трубопроводы, предназначенные для транспортировки воды от места ее забора, до места возможного возгорания. Использован насос UGP-M-1210-04. Задачи исследования: анализ результатов испытаний; получение эмпирических зависимостей показателей работы насоса от его производительности, исследования работы насоса в сети. Проведены расчеты скорости истекающей струи и полной реактивной силы в рабочей точке насосной установки. Исследовано влияние скорости на реактивную силу. Анализ результатов показывает, что точность расчетов приемлема для инженерных расчетов. Полученный алгоритм расчета может быть использован при проектировании систем тушения пожаров в портовых сооружениях. The purpose of the article is to develop an algorithm for calculating the hydraulic characteristics of a fire extinguishing system for port facilities. The fire extinguishing system has a submersible pump, pipelines intended for transporting water from the place of its intake to the place of possible ignition. The UGP-M-1210-04 pump is used. Research objectives: analysis of test results; obtaining empirical dependencies of pump performance indicators on its performance, research of pump operation in the network. Calculations of the velocity of the expiring jet and the total reactive force at the working point of the pumping unit are carried out. The effect of velocity on the reactive force is investigated. Analysis of the results shows that the accuracy of calculations is acceptable for engineering calculations. The resulting calculation algorithm can be used in the design of fire extinguishing systems in port facilities.

Pemberian Umpan Balik Dalam Meningkatkan Hasil Belajar dan Minat Belajar Mahasiswa

2015 ◽  
Vol 4 (3) ◽  
Author(s):  
Seruni Seruni ◽  
Nurul Hikmah
Keyword(s):  
Information Technology ◽  
Learning Outcomes ◽  
Test Data ◽  
Random Sampling ◽  
Covariance Matrices ◽  
Test Results ◽  
Immediate Feedback ◽  
Statistics Course ◽  
Independent Variable ◽  
Descriptive Statistical Analysis

<p>The purpose of this study is to find and analyze the effect of feedback on <br />learning outcomes in mathematics and an interest in basic statistics course. The <br />population in this study are affordable Information Technology Student cademic Year 2012/2013 Semester II Indraprasta PGRI University of South Jakarta. Sample The study sample was obtained through random sampling. This study used an experimental method to the analysis using the MANOVA test. This study has three variables, consisting of: one independent variable, namely the provision of feedback (immediate and delayed), and two dependent variable is the result of interest in the study of mathematics and basic statistics course. The data was collected for the test results to learn mathematics, and a questionnaire for the interest in basic statistics course. Collected data were analyzed using the MANOVA test. Before the data were analyzed, first performed descriptive statistical analysis and test data analysis requirements (test data normality and homogeneity of covariance matrices). The results show that the learning outcomes of interest in mathematics and basic statistics course for students who are given immediate feedback higher than students given feedback delayed. <br /><br /></p>

Measurements of Rotordynamic Coefficients of Hybrid Bearings With (a) a Plugged Orifice, and (b) a Worn Land Surface

2002 ◽  
Vol 124 (2) ◽  
pp. 363-368 ◽  
Author(s):  
F. Laurant ◽  
D. W. Childs
Keyword(s):  
Test Data ◽  
Land Surface ◽  
Rocket Engine ◽  
Liquid Rocket Engine ◽  
Test Results ◽  
Rotordynamic Coefficients ◽  
Hybrid Bearing ◽  
Liquid Rocket

Test results are presented for the rotordynamic coefficients of a hybrid bearing that is representative of bearings for liquid-rocket-engine turbopump applications. The bearing is tested in the following two degraded conditions: (a) one of five orifices plugged, and (b) a locally enlarged clearance to simulate a worn condition. Test data are presented at 24,600 rpm, with supply pressures of 4.0, 5.5, and 7.0 MPa, and eccentricity ratios from 0.1 to 0.5 in 0.1 increments. Overall, the results suggest that neither a single plugged orifice nor significant wear on the bearing land will “disable” a well-designed hybrid bearing. These results do not speak to multiple plugged orifices and are not an endorsement for operations without filters to prevent plugging orifices.

MENINGKATKAN KETERAMPILAN MENULIS PUISI MELALUI MEDIA TULISAN BERGAMBAR (MEME) DI INSTAGRAM PADA PESERTA DIDIK KELAS VIII G SMPN 24 SURABAYA

Buana Bastra ◽  
2020 ◽  
Vol 7 (2) ◽  
pp. 26-31
Author(s):  
Prily Yulia Utomo Putri ◽  
Tri Indrayanti
Keyword(s):  
Data Analysis ◽  
Data Collection ◽  
Test Data ◽  
Writing Skills ◽  
Test Results ◽  
Population Activity ◽  
Data Analysis Technique ◽  
Analysis Technique ◽  
Class Viii

This research is a research follow class by using the secound cycle that there is the first cycle and cycle II. On the cycle I and cycle II each cycle there four stage of the (1) planning, (2) implementation of action, (3) observations, and (4) reflection. Each cycle has two meetings in one week, namely the first meeting and the second meeting with the allocation 2 x 40 minutes of each meeting. Subject in research is learners class VIII G SMPN 24 Surabaya totaling 37 learners contained 16 learners men and 21 learners woman. This school is located in Jl. Kebraon Indah Permai Blok K/23 A Surabaya. Data collection techniques to use the observation and test, data analysis technique using the percentage of. Based on the results of data analysis, it can be concluded that using pictorial writing media on the meme on Instagram can improve the writing skills of class students VIII G SMPN 24 Surabaya. This can be seen from (1) population activity in the cycle I 84,61% on the cycle II 100%, (2) activity learners in cycle I 83,44% on the cycle II 90,20%, (3) the test results writing skills poerty in cycle I 56,73% one the cycle of II increased 83,70%.

Durability of BFRP and Hybrid FRP Sheets under Freeze-Thaw Cycling

2010 ◽  
Vol 163-167 ◽  
pp. 3297-3300 ◽  
Author(s):  
Jia Wei Shi ◽  
Hong Zhu ◽  
Zhi Shen Wu ◽  
Gang Wu
Keyword(s):  
Mechanical Properties ◽  
Test Data ◽  
Mechanical Characteristics ◽  
Test Results ◽  
Freeze Thaw ◽  
Frp Composites ◽  
Test Parameters ◽  
The Stability ◽  
Better Than

Coupon tests were conducted to investigate the mechanical characteristics of basalt FRP (BFRP) sheet, basalt-carbon hybrid FRP sheets and the corresponding epoxy rein under the effect of freeze-thaw cycling. FRP sheets and epoxy rein coupons were subjected to up to 200 and 250 freeze-thaw cycles respectively. Test parameters included the number of freeze-thaw cycles and the types of FRP composites. Test results show that (1) BFRP sheet perform better than CFRP or GFRP sheets under high freeze-thaw cycles; (2) exposed hybrid FRP sheets not only show very little loss in mechanical properties, but also contribute to the stability of test data; (3) mechanical properties of rein epoxy decrease significantly with increasing freeze-thaw cycles.

Leakage, Drag Power and Rotordynamic Force Coefficients of an Air in Oil (Wet) Annular Seal

2017 ◽  
Author(s):  
Luis San Andrés ◽  
Xueliang Lu
Keyword(s):  
Test Data ◽  
Volume Fraction ◽  
Damping Coefficient ◽  
Liquid Volume ◽  
Pure Liquid ◽  
Test Results ◽  
Liquid Volume Fraction ◽  
Force Coefficients ◽  
Damping Coefficients ◽  
Annular Seal

Wet gas compression systems and multiphase pumps are enabling technologies for the deep sea oil and gas industry. This extreme environment determines both machine types have to handle mixtures with a gas in liquid volume fraction (GVF) varying over a wide range (0 to 1). The gas (or liquid) content affects the system pumping (or compression) efficiency and reliability, and places a penalty in leakage and rotordynamic performance in secondary flow components, namely seals. In 2015, tests were conducted with a short length smooth surface annular seal (L/D = 0.36, radial clearance = 0.127 mm) operating with an oil in air mixture whose liquid volume fraction (LVF) varied to 4%. The test results with a stationary journal show the dramatic effect of a few droplets of liquid on the production of large damping coefficients. This paper presents further measurements and predictions of leakage, drag power, and rotordynamic force coefficients conducted with the same test seal and a rotating journal. The seal is supplied with a mixture (air in ISO VG 10 oil), varying from a pure liquid to an inlet GVF = 0.9 (mostly gas), a typical range in multiphase pumps. For operation with a supply pressure (Ps) up to 3.5 bar (a), discharge pressure (Pa) = 1 bar (a), and various shaft speed (Ω) to 3.5 krpm (ΩR = 23.3 m/s), the flow is laminar with either a pure oil or a mixture. As the inlet GVF increases to 0.9 the mass flow rate and drag power decrease monotonically by 25% and 85% when compared to the pure liquid case, respectively. For operation with Ps = 2.5 bar (a) and Ω to 3.5 krpm, dynamic load tests with frequency 0 < ω < 110 Hz are conducted to procure rotordynamic force coefficients. A direct stiffness (K), an added mass (M) and a viscous damping coefficient (C) represent well the seal lubricated with a pure oil. For tests with a mixture (GVFmax = 0.9), the seal dynamic complex stiffness Re(H) increases with whirl frequency (ω); that is, Re(H) differs from (K-ω2M). Both the seal cross coupled stiffnesses (KXY and −KYX) and direct damping coefficients (CXX and CYY) decrease by approximately 75% as the inlet GVF increases to 0.9. The finding reveals that the frequency at which the effective damping coefficient (CXXeff = CXX-KXY/ω) changes from negative to positive (i.e., a crossover frequency) drops from 50% of the rotor speed (ω = 1/2 Ω) for a seal with pure oil to a lesser magnitude for operation with a mixture. Predictions for leakage and drag power based on a homogeneous bulk flow model match well the test data for operation with inlet GVF up to 0.9. Predicted force coefficients correlate well with the test data for mixtures with GVF up to 0.6. For a mixture with a larger GVF, the model under predicts the direct damping coefficients by as much as 40%. The tests also reveal the appearance of a self-excited seal motion with a low frequency; its amplitude and broad band frequency (centered at around ∼12 Hz) persist and increase as the gas content in the mixture increase. The test results show that an accurate quantification of wet seals dynamic force response is necessary for the design of robust subsea flow assurance systems.

scholarly journals The use of the method of controlling the electrochemical parameters of aqueous solutions to combat complications in the operation of oil field pipelines

2021 ◽  
Vol 225 ◽  
pp. 01008
Author(s):  
Oleg Latypov ◽  
Sergey Cherepashkin ◽  
Dina Latypova
Keyword(s):  
Aqueous Solutions ◽  
Oil And Gas ◽  
High Efficiency ◽  
Oil Field ◽  
Oil Fields ◽  
Control Methods ◽  
Test Results ◽  
Chemical Reagents ◽  
Electrochemical Parameters ◽  
Very High

Corrosion of equipment in the oil and gas complex is a global problem, as it contributes to huge material costs and global disasters that violate the environment. Corrosion control methods used to protect equipment do not always ensure the absolute safety of the operation of oil and gas facilities. Moreover, they are quite expensive. The developed method for controlling the electrochemical parameters of aqueous solutions to combat complications during the operation of oil-field pipelines provides the necessary protection against corrosion. The method is economical and environmentally friendly, since it does not require the use of chemical reagents. The test results have shown a very high efficiency in dealing with complications in oil fields.

scholarly journals Analysis of the Problems and Safety Measures of Magnesium Fires

2020 ◽  
Vol 20 (2) ◽  
pp. 95-104
Author(s):  
Euipyeong Lee
Keyword(s):  
Research And Development ◽  
Safety Management ◽  
Case Analysis ◽  
Fire Fighting ◽  
Fire Prevention ◽  
Safety Measures ◽  
Fire Extinguishing

The problems and safety measures for magnesium fires were analyzed based on the fire case analysis in this study. The following problems were analyzed: ① the fire occurs in areas where there is no regulation under the Hazardous Goods Safety Management Act, ② the lack of safety measures during the firefighting of magnesium fires, ③ absence of adaptive fire fighting agents or equipment, ④ absence of suitable fire fighting tactics. For safety measures, the following were analyzed: ① enactment of magnesium fire guidelines, ② the education and publicity regarding fire prevention and countermeasures by fire organizations, ③ the obligation to have appropriate fire extinguishing agents in the places where magnesium is stored and handled, ④ the development of suppression equipment and fire fighting tactics, and ⑤ the research and development of fire extinguishing agents.

scholarly journals Time interval measurement module implemented in SoC FPGA device

2016 ◽  
Vol 62 (3) ◽  
pp. 237-246 ◽  
Author(s):  
Grzegorz Grzęda ◽  
Ryszard Szplet
Keyword(s):  
Mass Measurement ◽  
Measurement Data ◽  
Measurement Instrument ◽  
General Concept ◽  
Time Interval ◽  
Processing Unit ◽  
Test Results ◽  
Interval Measurement ◽  
Time Interval Measurement ◽  
On Chip

Abstract We presents the design and test results of a picosecond-precision time interval measurement module, integrated as a System-on-Chip in an FPGA device. Implementing a complete measurement instrument of a high precision in one chip with the processing unit gives an opportunity to cut down the size of the final product and to lower its cost. Such approach challenges the constructor with several design issues, like reduction of voltage noise, propagating through power lines common for the instrument and processing unit, or establishing buses efficient enough to transport mass measurement data. The general concept of the system, design hierarchy, detailed hardware and software solutions are presented in this article. Also, system test results are depicted with comparison to traditional ways of building a measurement instrument.

scholarly journals Implementasi Algoritma You Only Look Once (YOLO) untuk Deteksi Korban Bencana Alam

2021 ◽  
Vol 8 (4) ◽  
pp. 787
Author(s):  
Moechammad Sarosa ◽  
Nailul Muna
Keyword(s):  
Image Processing ◽  
Natural Disasters ◽  
Natural Disaster ◽  
Test Data ◽  
Detection System ◽  
Training Data ◽  
Test Results ◽  
Disaster Victim ◽  
Rapid Evacuation

<p class="Abstrak">Bencana alam merupakan suatu peristiwa yang dapat menyebabkan kerusakan dan menciptakan kekacuan. Bangunan yang runtuh dapat menyebabkan cidera dan kematian pada korban. Lokasi dan waktu kejadian bencana alam yang tidak dapat diprediksi oleh manusia berpotensi memakan korban yang tidak sedikit. Oleh karena itu, untuk mengurangi korban yang banyak, setelah kejadian bencana alam, pertama yang harus dilakukan yaitu menemukan dan menyelamatkan korban yang terjebak. Penanganan evakuasi yang cepat harus dilakukan tim SAR untuk membantu korban. Namun pada kenyataannya, tim SAR mengalami kendala selama proses evakuasi korban. Mulai dari sulitnya medan yang dijangkau hingga terbatasnya peralatan yang dibutuhkan. Pada penelitian ini sistem diimplementasikan untuk deteksi korban bencana alam yang bertujuan untuk membantu mengembangkan peralatan tim SAR untuk menemukan korban bencana alam yang berbasis pengolahan citra. Algoritma yang digunakan untuk mendeteksi ada atau tidaknya korban pada gambar adalah <em>You Only Look Once</em> (YOLO). Terdapat dua macam algoritma YOLO yang diimplementasikan pada sistem yaitu YOLOv3 dan YOLOv3 Tiny. Dari hasil pengujian yang telah dilakukan didapatkan <em>F1 Score</em> mencapai 95.3% saat menggunakan YOLOv3 dengan menggunakan 100 data latih dan 100 data uji.</p><p class="Abstrak"> </p><p class="Abstrak"><strong><em>Abstract</em></strong></p><p class="Abstrak"> </p><p class="Abstract"><em>Natural disasters are events that can cause damage and create havoc. Buildings that collapse and can cause injury and death to victims. Humans can not predict the location and timing of natural disasters. After the natural disaster, the first thing to do is find and save trapped victims. The handling of rapid evacuation must be done by the SAR team to help victims to reduce the amount of loss due to natural disasters. But in reality, the process of evacuating victims of natural disasters is still a lot of obstacles experienced by the SAR team. It was starting from the difficulty of the terrain that is reached to the limited equipment needed. In this study, a natural disaster victim detection system was designed using image processing that aims to help find victims in difficult or vulnerable locations when directly reached by humans. In this study, a detection system for victims of natural disasters was implemented which aims to help develop equipment for the SAR team to find victims of natural disasters based on image processing. The algorithm used is You Only Look Once (YOLO). In this study, two types of YOLO algorithms were compared, namely YOLOv3 and YOLOv3 Tiny. From the test results that have been obtained, the F1 Score reaches 95.3% when using YOLOv3 with 100 training data and 100 test data.</em></p>

Sign in / Sign up

Export Citation Format

Share Document