Preparation and Photo-catalytic Activity of Cu-Supported Nano-TiO2

2020 ◽  
Vol 1 (1) ◽  
pp. 38-42
Author(s):  
Jun Yan
Keyword(s):  
Catalytic Activity ◽  
Methyl Orange ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Nano Tio2 ◽  
Hydrolysis Method ◽  
Response Range ◽  
Photo Response ◽  
Forced Hydrolysis ◽  
Visible Photocatalytic Activity

Cu-supported nano-TiO2 catalyst was prepared by forced hydrolysis method under mild condition. The morphology, composition and optical absorption properties of the samples were characterized by means of scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and UV-Vis diffuse reflectance spectroscopy (UV-VIS DRS). Visible photocatalytic activity of the samples was investigated by photocatalytic degradation experiment on methyl orange. The results indicated that nano-TiO2 was about 20nm in size with the main form of anatase, and photo response range was significantly broadened after it was loaded on the surface of Cu. The sample possessed high visible light catalytic activity, with the degradation rate of methyl orange reaching 94% under simulated natural light.

VISIBLE LIGHT ACTIVE Cu2+/TiO2 NANOCATALYST FOR DEGRADATION OF DICHLORVOS

2012 ◽  
Vol 11 (05) ◽  
pp. 1250030 ◽  
Author(s):  
TESHOME ABDO SEGNE ◽  
SIVA RAO TIRUKKOVALLURI ◽  
SUBRAHMANYAM CHALLAPALLI
Keyword(s):  
Catalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Light Illumination ◽  
X Ray ◽  
Photo Catalytic Activity ◽  
Visible Light Active ◽  
Adsorption Desorption

The advantage of doping of TiO2 with copper has been utilized for enhanced degradation of pesticide under visible light irradiation. The sol–gel method has been undertaken for the synthesis of copper-doped TiO2 by varying the dopant loadings from 0.25 wt.% to 1.0 wt.% of Cu2+ . The doped samples were characterized by UV-Visible Diffuse Reflectance Spectroscopy (DRS), N2 adsorption–desorption (BET), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectrometry (EDS). The photocatalytic activity of the catalyst was tested by degradation of dichlorvos under visible light illumination. The results found that 0.75 wt.% of Cu2+ doped nanocatalysts have better photo catalytic activity than the rest of percentages doped, undoped TiO2 and Degussa P25. The reduction of band gap was estimated and the influence of the process parameters on photo catalytic activity of the catalyst has been explained.

Preparation and Properties of Eu3+-Doped TiO2 Nanowires

2012 ◽  
Vol 624 ◽  
pp. 67-71
Author(s):  
Si Qin Zhao ◽  
Hong Liang Wan ◽  
S. Asuha
Keyword(s):  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sodium Titanate ◽  
X Ray ◽  
Valence States ◽  
Photocatalytic Activities ◽  
Crystallite Sizes ◽  
Degradation Of Methyl Orange

Nanowires of sodium titanate, TiO2 and Eu3+/TiO2 were synthesized by hydrothermal method, and their microstructure, optical properties and valence states of exterior elements were characterized by X-ray powder diffraction (XRD), scanning electron microscopy(SEM), X-ray photoelectron spectroscopy (XPS) and UV-Vis diffuse reflectance spectroscopy techniques. At the same time, the photocatalytic activities of the materials for degradation of methyl orange under visible-light irradiation were also investigated. The results showed the formation of nanowires of sodium titanate with average crystallite sizes of 50-200 nm and in lengths from several microns to several dozens microns, and its chemical formula was determined to be Na2Ti3O7. TiO2 and Eu3+ /TiO2nanowires were prepared from the Na2Ti3O7 nanowires via ion exchange (i.e., with H+ and Eu3+ ions) and high temperature sintering processes. These three kinds of nanowires showed different photocatalytic activities for degradation of methyl orange. Na2Ti3O7 nanowire did not show any photocatalytic activity for methyl orange degradation, while TiO2 nanowire was superior to Na2Ti3O7 nanowire; and, Eu3+/ TiO2 nanowire possessed the highest photocatalytic activity.

Comparison of the photocatalytic performance of TiO2/AC and TiO2/CNT nanocomposites for methyl orange photodegradation

2018 ◽  
Vol 78 (5) ◽  
pp. 1082-1093 ◽  
Author(s):  
Liping Wang ◽  
Jingru Guo ◽  
Jingjing Dang ◽  
Xiaojun Huang ◽  
Si Chen ◽  
...  
Keyword(s):  
Methyl Orange ◽  
Removal Efficiency ◽  
Photoelectron Spectroscopy ◽  
Photocatalytic Performance ◽  
Chloride Ion ◽  
Degradation Efficiency ◽  
Ion Concentration ◽  
Nano Tio2 ◽  
Ultraviolet Wavelength ◽  
Nanotube Composites

Abstract To enhance the photocatalytic degradation efficiency of TiO2 on methyl orange (MO) removal, TiO2/AC (activated carbon) and TiO2/CNT (carbon nanotube) composites were synthesized. The prepared catalysts were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The photocatalytic performance of the obtained composites were investigated by the degradation of MO under UV irradiation (254 nm, 365 nm). The results revealed that the prepared nanocomposite showed higher MO degradation efficiency than pure nano-TiO2. Additionally, batch experiments of influencing factors, including H2O2 dosage, metal dopants, inorganic anions, chloride ion concentration and ultraviolet wavelength on the MO removal efficiency were also conducted. The results demonstrated that metal dopant and the presence of H2O2 significantly enhanced MO removal efficiency.

scholarly journals Photocatalytic Activity of Magnetic Nano-β-FeOOH/Fe3O4/Biochar Composites for the Enhanced Degradation of Methyl Orange Under Visible Light

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 526
Author(s):  
Zheng Zhang ◽  
Guanghua Wang ◽  
Wenbing Li ◽  
Lidong Zhang ◽  
Benwei Guo ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Catalytic Activity ◽  
Methyl Orange ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Azo Dye ◽  
Photocatalytic Performance ◽  
Active Species ◽  
Step Method ◽  
Vis Spectroscopy

A novel nano-β-FeOOH/Fe3O4/biochar composite with enhanced photocatalytic performance and superparamagnetism was successfully fabricated via an environmentally friendly one-step method. The structural properties of the prepared composite were characterized by scanning electron microscopy, transmission electron microscopy, energy-dispersive spectroscopy, X-ray photoelectron spectroscopy, and a vibrating sample magnetometer. The XPS spectrum of the as-prepared composites confirmed the presence of Fe-O-C bonds between β-FeOOH and biochar, which could be conducive to transfer photo-generated electrons. UV-vis spectroscopy confirmed the existence of an electron–hole connection between β-FeOOH and biochar, which promoted the rapid interface transfer of photogenerated electrons from β-FeOOH to biochar. These novel structures could enhance the response of biochar to accelerate the photoelectrons under visible light for more free radicals. Electron spin resonance analysis and free radical quenching experiments showed that •OH was the primary active species in the photodegradation process of methyl orange by nano-β-FeOOH/Fe3O4/biochar. In the synergistic photocatalytic system, β-FeOOH/Fe3O4/biochar exhibited excellent catalytic activity for the degradation of azo dye (methyl orange), which is 2.03 times higher than that of the original biochar, while the surface area decreased from 1424.82 to 790.66 m2·g−1. Furthermore, β-FeOOH/Fe3O4/biochar maintained a stable structure and at least 98% catalytic activity after reuse, and it was easy to separate due to its superparamagnetism. This work highlights the enhanced photocatalytic performance of β-FeOOH/Fe3O4/biochar material, which can be used in azo dye wastewater treatment.

scholarly journals Heterogeneous UV/Fenton-Like Degradation of Methyl Orange Using Iron Terephthalate MIL-53 Catalyst

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Pham Dinh Du ◽  
Huynh Thanh Danh ◽  
Pham Ngoc Hoai ◽  
Nguyen Mau Thanh ◽  
Vo Thang Nguyen ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Methyl Orange ◽  
Photoelectron Spectroscopy ◽  
Nitrogen Adsorption ◽  
High Catalytic Activity ◽  
Potential Candidate ◽  
Factors Affecting ◽  
X Ray ◽  
Activity Loss ◽  
Degradation Of Methyl Orange

The synthesis and degradation of methyl orange (MO) in an ultraviolet-assisted heterogeneous Fenton-like process via the iron terephthalate (MIL-53) catalyst are demonstrated. MIL-53 material was characterized by means of X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), UV-Vis diffuse reflectance spectra (DR-UV-Vis), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and nitrogen adsorption/desorption isotherms. It was found that the obtained material shares an identical pattern of the MIL-53 structure with high crystallinity and also demonstrates the mesoporous phase with a pore diameter of around 4.2 nm and specific surface area, SBET, of 88.2 m2·g−1. MIL-53 with UV irradiation exhibits high catalytic activity for MO degradation by hydrogen peroxide. The factors affecting the efficiency of MO decomposition including pH of the solution, H2O2 concentration, catalyst dosage, initial MO concentration, and reaction temperature were addressed. The present catalyst is stable after four recycles with slight catalytic activity loss which makes it a potential candidate for environmental restoration.

scholarly journals Solvothermal Synthesis of ZnO Nanoparticles for Photocatalytic Degradation of Methyl Orange and p-Nitrophenol

Water ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3224
Author(s):  
Ying Wang ◽  
Chuanxi Yang ◽  
Yonglin Liu ◽  
Yuqi Fan ◽  
Feng Dang ◽  
...  
Keyword(s):  
Methyl Orange ◽  
Photocatalytic Degradation ◽  
Zno Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Zno Nps ◽  
Uniform Size ◽  
X Ray ◽  
Degradation Rates ◽  
Degradation Of Methyl Orange

The photocatalytic degradation of organic pollutants is an effective method of controlling environmental pollution. ZnO nanoparticles (ZnO NPs) were prepared by the solvothermal method and characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV–visible diffuse reflectance spectroscopy (UV–Vis DRS). The results showed that the ZnO NPs had a uniform size of 25–40 nm, hexagonal wurtzite structure, and a band gap of 2.99 eV. The photocatalytic degradation of methyl orange (MO) and p-nitrophenol (PNP) was used as a model reaction to evaluate the photocatalytic activity of ZnO NPs. The photocatalytic degradation rates (pseudo-first-order kinetics) of MO and PNP were 92% (0.0128 min−1) and 56.2% (0.0042 min−1), respectively, with a 25 W ultraviolet lamp, MO/PNP concentration = 20 mg/L, ZnO NPs dose = 1.5 g/L, and time = 180 min. The photocatalytic mechanism of ZnO NPs and degradation pathways of MO and PNP were also proposed. The results provide valuable information and guidance for the treatment of wastewater via photocatalytic methods.

scholarly journals Enhanced Photocatalytic Activity of CuWO4 Doped TiO2 Photocatalyst Towards Carbamazepine Removal under UV Irradiation

Separations ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 25
Author(s):  
Chukwuka Bethel Anucha ◽  
Ilknur Altin ◽  
Emin Bacaksız ◽  
Tayfur Kucukomeroglu ◽  
Masho Hilawie Belay ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Component Part ◽  
Energy Yield ◽  
Mechanical Agitation ◽  
X Ray

Abatement of contaminants of emerging concerns (CECs) in water sources has been widely studied employing TiO2 based heterogeneous photocatalysis. However, low quantum energy yield among other limitations of titania has led to its modification with other semiconductor materials for improved photocatalytic activity. In this work, a 0.05 wt.% CuWO4 over TiO2 was prepared as a powder composite. Each component part synthesized via the sol-gel method for TiO2, and CuWO4 by co-precipitation assisted hydrothermal method from precursor salts, underwent gentle mechanical agitation. Homogenization of the nanopowder precursors was performed by zirconia ball milling for 2 h. The final material was obtained after annealing at 500 °C for 3.5 h. Structural and morphological characterization of the synthesized material has been achieved employing X-ray diffraction (XRD), Fourier transform infra-red (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) N2 adsorption–desorption analysis, Scanning electron microscopy-coupled Energy dispersive X-ray spectroscopy (SEM-EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) for optical characterization. The 0.05 wt.% CuWO4-TiO2 catalyst was investigated for its photocatalytic activity over carbamazepine (CBZ), achieving a degradation of almost 100% after 2 h irradiation. A comparison with pure TiO2 prepared under those same conditions was made. The effect of pH, chemical scavengers, H2O2 as well as contaminant ion effects (anions, cations), and humic acid (HA) was investigated, and their related influences on the photocatalyst efficiency towards CBZ degradation highlighted accordingly.

scholarly journals Facile Synthesis of Uniform Mesoporous Nb2O5 Micro-Flowers for Enhancing Photodegradation of Methyl Orange

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3783
Author(s):  
Jian-Qing Qiu ◽  
Huan-Qing Xie ◽  
Ya-Hao Wang ◽  
Lan Yu ◽  
Fang-Yuan Wang ◽  
...  
Keyword(s):  
Methyl Orange ◽  
Active Sites ◽  
High Performance ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
Flower Structure ◽  
Electron Microscopies ◽  
Bet Method ◽  
One Step ◽  
Catalytic Active Sites

The removal of organic pollutants using green environmental photocatalytic degradation techniques urgently need high-performance catalysts. In this work, a facile one-step hydrothermal technique has been successfully applied to synthesize a Nb2O5 photocatalyst with uniform micro-flower structure for the degradation of methyl orange (MO) under UV irradiation. These nanocatalysts are characterized by transmission and scanning electron microscopies (TEM and SEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) method, and UV-Vis diffuse reflectance spectroscopy (DRS). It is found that the prepared Nb2O5 micro-flowers presents a good crystal phases and consist of 3D hierarchical nanosheets with 400–500 nm in diameter. The surface area is as large as 48.6 m2 g−1. Importantly, the Nb2O5 micro-flowers exhibit superior catalytic activity up to 99.9% for the photodegradation of MO within 20 mins, which is about 60-fold and 4-fold larger than that of without catalysts (W/O) and commercial TiO2 (P25) sample, respectively. This excellent performance may be attributed to 3D porous structure with abundant catalytic active sites.

scholarly journals Study of the Effect of TiO2 Layer on the Adsorption and Photocatalytic Activity of TiO2-MoS2 Heterostructures under Visible-Infrared Light

2020 ◽  
Vol 2020 ◽  
pp. 1-9 ◽  
Author(s):  
N. Cruz-González ◽  
O. Calzadilla ◽  
J. Roque ◽  
F. Chalé-Lara ◽  
J. K. Olarte ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Nitrogen Adsorption ◽  
High Photocatalytic Activity ◽  
Infrared Light ◽  
Polluted Water ◽  
Light Spectrum ◽  
X Ray

In the last decade, the urgent need to environmental protection has promoted the development of new materials with potential applications to remediate air and polluted water. In this work, the effect of the TiO2 thin layer over MoS2 material in photocatalytic activity is reported. We prepared different heterostructures, using a combination of electrospinning, solvothermal, and spin-coating techniques. The properties of the samples were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), X-ray diffraction (XRD), nitrogen adsorption-desorption isotherms, UV-Vis diffuse reflectance spectroscopy (UV-Vis-DRS), and X-ray photoelectron spectroscopy (XPS). The adsorption and photocatalytic activity were evaluated by discoloration of rhodamine B solution. The TiO2-MoS2/TiO2 heterostructure presented three optical absorption edges at 1.3 eV, 2.28 eV, and 3.23 eV. The high adsorption capacity of MoS2 was eliminated with the addition of TiO2 thin film. The samples show high photocatalytic activity in the visible-IR light spectrum.

scholarly journals Study on Synthesis and Photocatalytic Activity of Porous Titania Nanotubes

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Huang Liu ◽  
Yanhua Zhang ◽  
Hongtao Yang ◽  
Wei Xiao ◽  
Lanlan Sun
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Filter Paper ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Cellulose Nanofibers ◽  
Titania Nanotubes ◽  
Tetrabutyl Titanate ◽  
X Ray ◽  
Porous Titania

Using the common natural cellulose substance (filter paper) and triblock copolymer (Pluronic P123) micelles as dual templates, porous titania nanotubes with enhanced photocatalytic activity have been successfully synthesized through sol-gel methods. Firstly, P123 micelles were adsorbed onto the surfaces of cellulose nanofibers of filter paper, followed by hydrolysis and condensation of tetrabutyl titanate around these micelles to form titania layer. After calcination to remove the organic templates, hierarchical titania nanotubes with pores in the walls were obtained. The sample was characterized by X-ray diffraction pattern (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen adsorption/desorption, Fourier Transform Infrared Spectroscopy (FT-IR), Ultraviolet-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS), and X-ray photoelectron spectroscopy (XPS). As compared with commercial P25 catalyst, the porous titania nanotubes prepared by this method displayed significantly enhanced photocatalytic activity for degrading methyl orange under UV irradiation. Within 10 minutes, the porous titania nanotubes are able to degrade over 70% of the original MO, while the value for the commercial Degussa P25 is only about 33%.

Sign in / Sign up

Export Citation Format

Share Document