Isotherm and Kinetic Models for Bio-sorption of Cadmium Ions from Aqueous Solutions using Dry Peanut Shells and Hazelnut Shells

2018 ◽  
Vol 69 (10) ◽  
pp. 2603-2607
Author(s):  
Firas Hashim Kamar ◽  
Salman H. Abbas ◽  
Asem Hassan Mohammed ◽  
Mihaela Emanuela Craciun ◽  
Aurelia Cristina Nechifor
Keyword(s):  
Removal Efficiency ◽  
Contact Time ◽  
Room Temperature ◽  
Sorption Kinetics ◽  
Initial Concentration ◽  
Several Variables ◽  
Peanut Shells ◽  
Before And After ◽  
Isotherm And Kinetic Models ◽  
Hazelnut Shells

This work is aiming to investigate the removal Cd(II) ions from the aqueous solution using two types of biosorbent materials: peanut shells (PS) and hazelnut shells (HS). The effect of several variables on the batch bio-sorption was studied. The process was carried out at room temperature, shacking speed 200 rpm and using fixed adsorbent diameters of 0.75 mm. The highest removal efficiency of Cd(II) ions onto PS was 91.45% in the best conditions (pH=3, initial concentration of Cd(II) ions 50 mg/ L, amount adsorbent was 0.75 g, contact time was 120 min), while the highest removal efficiency when using HS was 85.62% at pH= 4, and contact time of 160 minutes using the same initial concentration of Cd(II) ions as well as the same amount of absorbent material. Isotherm was studied for bio-sorption of Cd(II) ions using these two adsorbents, and the pseudo- first and second order models were used to study bio-sorption kinetics. The results of the infrared spectroscopy (FTIR) of (PS) and (HS) samples before and after loading for Cd(II) ions showed that hydroxyl and carboxyl groups play a major role in bio-sorption of these ions.

scholarly journals Efficient removal of arsenic from water by dielectrophoresis-assisted adsorption

2018 ◽  
Vol 19 (4) ◽  
pp. 1066-1072
Author(s):  
Q. H. Jin ◽  
C. Y. Cui ◽  
H. Y. Chen ◽  
Y. Wang ◽  
J. F. Geng ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Solution Ph ◽  
Residual Concentration ◽  
Initial Concentration ◽  
Weight Percentage ◽  
Before And After ◽  
High Concentrations ◽  
Plant Ash ◽  
Adsorbent Dose

Abstract Adsorption (ADS) and dielectrophoresis (DEP) techniques were combined (ADS/DEP) to efficiently remove As(V) in industrial wastewater. Fly ash, activated carbon, corncob and plant ash were tested to determine the best adsorbent by their adsorption capacity. Plant ash showed the highest adsorption capacity compared with the others. Different parameters such as solution pH and adsorbent dose were explored. The maximum As(V) removal efficiency was 91.4% at the optimized conditions (pH 9.0, adsorbent dose 5 g/L) when the initial concentration of As(V) was 15 mg/L. With the ADS/DEP technique, the plant ash particles with adsorbed As(V) were trapped on the electrodes in a DEP device. The ADS/DEP process could increase the removal efficiency of As(V) to 94.7% at 14 V even when the initial concentration of As(V) was 15 mg/L. And the residual concentration of As(V) decreased to 0.34 mg/L after two series of the ADS/DEP process. The adsorbents before and after DEP were examined by scanning electron microscope (SEM) and energy dispersive X-ray (EDX) analysis. After the DEP process, the weight percentage of As(V) on the adsorbent surface increased to 0.96% from 0.5%. The ADS/DEP process could be a new efficient way to remove arsenic pollutant at high concentrations.

Amidoxime Functionalized Mesoporous SBA-15 with Various Mesostructures for Highly Efficient Concentration of U(VI)

NANO ◽  
2019 ◽  
Vol 14 (02) ◽  
pp. 1950027
Author(s):  
Ziyan Yang ◽  
Xiaoli Yang ◽  
Rui Hu ◽  
Junfeng Wu
Keyword(s):  
Surface Chemistry ◽  
Aqueous Solutions ◽  
Contact Time ◽  
High Selectivity ◽  
Ph Value ◽  
Sorption Kinetics ◽  
Initial Concentration ◽  
Geochemical Conditions ◽  
Pore Length ◽  
Ordered Mesoporous

Many current sorbents are limited for U(VI) concentration from aqueous solutions due to their inappropriate structures and surface chemistry. Herein, we report the rapid sorption of U(VI) with high capacities and selectivity by amidoxime modified ordered mesoporous SBA-15 with two typical morphologies (i.e., rods and plates) via a post-grafting method. Variables of the geochemical conditions (contact time, pH value, initial concentration, temperature and coexisting metal ions) are investigated. The results show that the mesostructures including morphologies and pore length of SBA-15 perform the dominant function for the fast sorption kinetics (10[Formula: see text]min for plates, 20[Formula: see text]min for rods), while the modified amidoxime groups make the excellent U(VI) sorption capacities (646.2[Formula: see text]mg[Formula: see text][Formula: see text][Formula: see text]g[Formula: see text] for plates, 499.8[Formula: see text]mg[Formula: see text][Formula: see text][Formula: see text]g[Formula: see text] for rods at pH 5.0 and [Formula: see text] 298.15[Formula: see text]K) and high selectivity possible. U(VI) adsorbed amidoxime-functionalized SBA can also be effectively regenerated by HCl solutions and reused well after six cycles.

Preparation and Application of Electrospinning Membranes of Thermoplastic Carboxymethyl Cellulose/PLA for Removal of Cu2+ from Aqueous Solutions

2012 ◽  
Vol 724 ◽  
pp. 61-64
Author(s):  
Ying Li ◽  
Xiao Yan Lin ◽  
Zhe Chen ◽  
Xue Guang Luo ◽  
Wei Li Zuo
Keyword(s):  
Tensile Strength ◽  
Aqueous Solutions ◽  
Removal Efficiency ◽  
Composite Membrane ◽  
Carboxymethyl Cellulose ◽  
Contact Time ◽  
Electrospinning Process ◽  
Cross Linking ◽  
Initial Concentration ◽  
The Cross

A composite membrane of thermoplastic carboxymethyl cellulose (TCMC) /PLA was prepared by electrospinning process, and crossliked by epichlorohydrin solution at different temperature. The cross-linking temperature was optimized by characterizing the morphology and tensile strength of the film. The optimal cross-linking temperature was 50°C. A composite membrane was used to remove Cu2+ from aqueous solutions, and the effects of initial concentration of Cu2+ and contact time on the removal efficiency of Cu2+ were investigated. The removal efficiency of Cu2+ was 13.78%, at the initial concentration of 40 mg·L-1 and contact time of 30s.

Treatment of Dye Wastewater by Adsorption with Bentonite-Supported Magnetic Materials

2011 ◽  
Vol 340 ◽  
pp. 487-491
Author(s):  
Xiao Ming Chen ◽  
Jian Feng Ma ◽  
Ding Long Li
Keyword(s):  
Removal Efficiency ◽  
Contact Time ◽  
Magnetic Particles ◽  
Influence Factor ◽  
Dye Wastewater ◽  
No Adsorption ◽  
Initial Concentration ◽  
Magnetite Particles ◽  
Co Precipitation ◽  
Maximum Removal

Bentonite-supported magnetite particles (MagBt-p) were prepared by co-precipitation. The adsorption capacity of Bentonite-supported magnetic particles on waste water containing OrangeⅡ was tested. Some influence factor such as the dose, the initial concentration of OrangeⅡ, the pH, the contact time and the presence of surfactant were studied. Results showed that cation surfactant (CTAB) greatly enhanced the adsorption of OrangeⅡ. The maximum removal efficiency was 96.6% at 180mg/L (CTAB) and beyond this concentration there was almost no adsorption. Besides, the removal efficiency was affected by pH and contact time, the maximum removal efficiency was found at pH 2.1-3, the adsorption was rapid during the first 120 min and then equilibrium within 180min.

scholarly journals Adsorption of Nickel and Chromium From Aqueous Solutions Using Copper Oxide Nanoparticles: Adsorption Isotherms, Kinetic Modeling, and Thermodynamic Studies

2019 ◽  
Vol 6 (2) ◽  
pp. 66-74 ◽  
Author(s):  
Raziyeh Hosseini ◽  
Mohammad Hossein Sayadi ◽  
Hossein Shekari
Keyword(s):  
Aqueous Solutions ◽  
Copper Oxide ◽  
Removal Efficiency ◽  
Contact Time ◽  
Removal Rate ◽  
Copper Oxide Nanoparticles ◽  
Isotherm Models ◽  
Oxide Nanoparticles ◽  
Initial Concentration ◽  
Adsorbent Dosage

The research was conducted with an aim to assess the efficiency of copper oxide nanoparticles as an adsorbent to remove Ni and Cr. The effect of pH, adsorbent dosage, contact time, initial concentration of metals (Ni and Cr) on the adsorption rate was evaluated and removal of these elements from aqueous solutions was measured using Atomic Absorption Spectrum System (Conter AA700). Moreover, the kinetic and isotherm besides thermodynamic adsorption models were assessed. The highest Ni and Cr removal rate occurred at an optimal pH of 7, and an initial concentration of 30 mg/L, a time period of 30 minutes, and 1 g/L of copper oxide nanoparticles. In fact, with the increase of adsorbent dosage and contact time, the removal efficiency increased and with initial concentration increase of Ni and Cr ions, the removal efficiency reduced. The correlation coefficient of isotherm models viz. Langmuir, Freundlich, Temkin, Redlich-Peterson, and Koble-Corrigan showed that Ni and Cr adsorption via copper oxide nanoparticles better follows the Langmuir model in relation to other models. The results showed that kinetic adsorption of Ni and Cr via copper oxide nanoparticles follows the second order pseudo model with correlation coefficients above 0.99. In addition, the achieved thermodynamic constants revealed that the adsorption process of metals (i.e., Ni and Cr) via copper oxide nanoparticles was endothermic and spontaneous and the reaction enthalpy values for these metals were 17.727 and 11.862 kJ/mol, respectively. In conclusion, copper oxide nanoparticles can be used as effective and environmentally compatible adsorbents to remove Ni and Cr ions from the aqueous solutions

scholarly journals Degradation Characteristics of Aniline with Ozonation and Subsequent Treatment Analysis

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Zhaoqian Jing ◽  
Shiwei Cao ◽  
Ting Yu ◽  
Jing Hu
Keyword(s):  
Hydroxyl Radicals ◽  
Contact Time ◽  
Room Temperature ◽  
Subsequent Treatment ◽  
Biological Processes ◽  
Initial Concentration ◽  
Alkaline Conditions ◽  
As Adsorption ◽  
Treatment Analysis ◽  
Operation Parameters

Owing to the toxicity and low biodegradability of aniline in water, its removal usually needs high cost processes such as adsorption and advanced oxidation. The degradation characteristics of aniline during ozonation were studied. The influence of operation parameters such as contact time, initial concentration, ozone dosage, temperature, and pH was also investigated. With ozone dosage of 22 mg/L, neutral pH, and room temperature, the ozonation removed aniline efficiently. After two hours’ ozonation, aniline removal reached 93.57%, and the corresponding COD removal was 31.03%, which indicated most of aniline was transformed into intermediates. At alkaline conditions, the aniline was more susceptible to being removed by ozonation owing to more hydroxyl radicals’ production. The results of GC-MS indicated many intermediates appeared during the process of ozonation such as butane diacid, oxalic acid, and formic acid. The intermediates produced during ozonation were more biodegradable than aniline; thus the ozonation of such organic compounds as aniline could be integrated with biological processes for further removal.

scholarly journals 3,5-Dichlorophenol Removal From Wastewater Using Alternative Adsorbents

2015 ◽  
Vol 23 (36) ◽  
pp. 25-32
Author(s):  
Hana Kobetičová ◽  
Marek Lipovský ◽  
Igor Wachter ◽  
Maroš Soldán
Keyword(s):  
Waste Water ◽  
Removal Efficiency ◽  
Red Mud ◽  
Contact Time ◽  
Lemna Minor ◽  
Low Cost ◽  
Initial Concentration ◽  
Black Nickel ◽  
Alternative Adsorbents

Abstract The main objective of this paper is to evaluate the efficiency of 3,5-dichlorophenol removal from wastewater by using alternative low cost adsorbents. Waste from the production and processing of metals (black nickel mud, red mud) and a biosorbent (Lemna minor) were used for this research. Initial concentration of the contaminant was 4 mmol L−1, the contact time of sorbent and waste water was 0 - 48 hrs and the temperature during experiment was 25 ± 0.2 °C. The results show that the highest removal efficiency of 3,5 - dichlorophenol (58.18 %) was reached by the red mud in 48 hours.

Synthesis of Calcium Peroxide Microparticles in Aqueous at Room Temperature and its Application in Heavy Metal Ions Removal from Waste Liquid of COD Determining

2013 ◽  
Vol 864-867 ◽  
pp. 648-653
Author(s):  
Jian Zhai ◽  
Chun Hua Jiang
Keyword(s):  
Heavy Metal ◽  
Reaction Time ◽  
Removal Efficiency ◽  
Contact Time ◽  
Heavy Metal Ions ◽  
Room Temperature ◽  
Efficient Removal ◽  
Calcium Peroxide ◽  
Heavy Metal Ions Removal ◽  
Metal Ions Removal

The calcium peroxide microparticles were synthesized and evaluated as an innovative oxidant to remove Fe (III) and Cr (III) from waste liquid of COD determining samples. The CaO2 microparticles were 0.1-0.3 μm in diameter and the average CaO2 content was 80%. Experiments were performed to investigate the influence of contact time, pH of solution and CaO2 microparticles dosage on the efficiency of Fe (III) and Cr (III) removal. Up to 100.0% and 99.8% removal efficiency for Fe (III) and Cr (III) respectively was obtained by microparticles dosage of 10000 mg/L at 30 min and pH 7.46. It could be concluded that the removal efficiency was enhanced by increasing CaO2 microparticles dosage and reaction time, but decreased by increasing pH. These results suggest that CaO2 microparticles may be used to develop a simple and efficient removal method for waste liquid of COD determining samples.

Innovative Process of Leaching of Nickel Supported Activated Carbon in Ammonium Sulfate

2011 ◽  
Vol 201-203 ◽  
pp. 1774-1779
Author(s):  
Ze Biao Zhang ◽  
Wan Kun Wang ◽  
Jin Hui Peng
Keyword(s):  
Activated Carbon ◽  
Atmospheric Pressure ◽  
Room Temperature ◽  
Normal Pressure ◽  
Leaching Rate ◽  
Initial Concentration ◽  
Comprehensive Utilization ◽  
Solid Ratio ◽  
Innovative Process ◽  
Before And After

The leaching tests of nickel supported activated carbon under normal pressure in (NH4)2SO4were studied. The effects of experimental condition, such as initial concentration of (NH4)2SO4, liquid-to-solid ratio, leaching time and leaching temperature on the leaching rate of nickel, were investigated. The results show that the leaching rate of nickel is 96.12% with initial concentration of (NH4)2SO4of 7.5%, liquid-to-solid ratio of 2, leaching time of 5h and leaching temperature of 25°C. The morphology of nickel supported activated carbon before and after leaching was characterized by XRD, which proved the effective separation of nickel and activated carbon. The leaching rate of nickel was also shown better at room temperature and atmospheric pressure. Moreover, it needn’t equipments enduring high-pressure and high temperature in the leaching process, thus reducing the costs of leaching equipments greatly. This work provides a new way to the comprehensive utilization of nickel-containing activated carbon.

scholarly journals Synthesis of Fe3O4 nanoparticles @Trioctylmethylammonium thiosalicylat (TOMATS) as a new magnetic nanoadsorbent for adsorption of ciprofloxacin in aqueous solution

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Ruhollah Kasraei ◽  
Mohammad Malakootian ◽  
Maryam Mohamadi
Keyword(s):  
Removal Efficiency ◽  
Contact Time ◽  
Physical Adsorption ◽  
Sorption Kinetics ◽  
Order Model ◽  
Solution Ph ◽  
Langmuir Adsorption ◽  
Ft Ir ◽  
Real Wastewater ◽  
Adsorbent Dose

AbstractThe aim of this research was to investigate ciprofloxacin (CIP) removal efficiency from aqueous solutions by using Fe3O4 nanoparticles @Trioctylmethylammonium thiosalicylat Ionic liquid (Fe3O4 NP@ TOMATS IL) as a new magnetic nanoadsorbent. The adsorbent was characterized by field emission scanning electron microscope-energy dispersive spectroscopy (FESEM-EDS), mapping, Fourier transform infrared spectroscopy (FT-IR), the Brunauer–Emmett–Teller (BET), X-ray powder diffraction (XRD). The effects of solution pH, adsorbent dose, contact time, initial CIP concentration, and temperature on CIP removal were also investigated. In optimal conditions such as pH = 5.6, CIP concentration = 30 mg/L, adsorbent dose = 0.15 g, temperature = 30 °C, contact time = 90 min, the removal efficiency in synthetic and real wastewater were obtained 87 and 73%, respectively. Batch experiments were carried out to study the sorption Kinetics, thermodynamics, and equilibrium isotherms of CIP with magnetic nanoadsorbent. The results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for four times.

Sign in / Sign up

Export Citation Format

Share Document