3D TRACHEOBRONCHIAL AIRWAY TREE SEGMENTATION FROM THORAX CT IMAGES

2013 ◽  
Vol 25 (01) ◽  
pp. 1350015 ◽  
Author(s):  
Nihad Mesanovic ◽  
Haris Huseinagic ◽  
Svjetlana Mujagic
Keyword(s):  
Gold Standard ◽  
Region Growing ◽  
Test Results ◽  
Qualitative And Quantitative ◽  
Airway Segmentation ◽  
Airway Tree ◽  
The Difference ◽  
Thorax Ct ◽  
Medical Analysis ◽  
Lung Ct

Segmentation of the lung structures is an important operation in the medical analysis. This paper is proposing a region growing algorithm for airway segmentation. The proposed method for the airway tree segmentation works fully in 3D and performs the measurements in the original gray-scale volume for increased accuracy and efficiency. This algorithm uses region growing and morphological operators. The airway segmentation algorithm is intended to serve qualitative and quantitative purposes, and additional three descriptors are being used for evaluation of the airway segmentation. The proposed method was evaluated using the database of 15 patients who underwent lung CT scans, with varying image quality and anatomical changes. Overlap measure is used to show the difference between measured volumes from the established gold standard and the proposed method. The student t-test and Pearson test showed high correlation of the results with the gold standard. Overall, the test results were satisfactory since accurate segmentation was achieved in 95% of the patients.

scholarly journals Influence of Tool Length and Profile Errors on the Inaccuracy of Cubic-Machining Test Results

2021 ◽  
Vol 5 (2) ◽  
pp. 51
Author(s):  
Zongze Li ◽  
Hiroki Ogata ◽  
Ryuta Sato ◽  
Keiichi Shirase ◽  
Shigehiko Sakamoto
Keyword(s):  
Machine Tools ◽  
Test Accuracy ◽  
Test Results ◽  
Machining Error ◽  
Tool Profile ◽  
Machining Test ◽  
The Difference ◽  
Side Error ◽  
Profile Errors ◽  
Five Axis

A cubic-machining test has been proposed to evaluate the geometric errors of rotary axes in five-axis machine tools using a 3 × 3 zone area in the same plane with different tool postures. However, as only the height deviation among the machining zones is detected by evaluating the test results, the machining test results are expected to be affected by some error parameters of tool sides, such as tool length and profile errors, and there is no research investigation on how the tool side error influences the cubic-machining test accuracy. In this study, machining inaccuracies caused by tool length and tool profile errors were investigated. The machining error caused by tool length error was formulated, and an intentional tool length error was introduced in the simulations and actual machining tests. As a result, the formulated and simulated influence of tool length error agreed with the actual machining results. Moreover, it was confirmed that the difference between the simulation result and the actual machining result can be explained by the influence of the tool profile error. This indicates that the accuracy of the cubic-machining test is directly affected by tool side errors.

scholarly journals Experimental Study of the Space–Time Effect of a Double-Pipe Frozen Curtain Formation with Different Groundwater Velocities

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3830
Author(s):  
Shicheng Sun ◽  
Chuanxin Rong ◽  
Hua Cheng ◽  
Bin Wang ◽  
Xiaogang Jiang ◽  
...  
Keyword(s):  
Freezing Temperature ◽  
Physical Model Test ◽  
Sand Layer ◽  
Test Results ◽  
Groundwater Velocity ◽  
Test Platform ◽  
The Difference ◽  
Freezing Test ◽  
Double Pipe ◽  
Thermal Physical Properties

Groundwater velocity has significant effects on the formation of a frozen curtain during freezing. In order to study the influence of the velocity on a frozen curtain, a large physical model test platform was established for double-pipe freezing. Based on this platform, freezing tests for different velocities were carried out. Quartz sand was selected as a similar material. The freezing temperature of the saturated sand layer was found by analyzing the results of the nuclear magnetic resonance (NMR). Based on the study of the thermal physical properties of the sand layer, the freezing test results were analyzed, and the results showed that the flow led to the differential development of the temperature between the upstream and downstream sections of the freezing pipes. Moreover, the larger the velocity, the greater the difference. The flow prolonged the overlapping time of the frozen curtains. Additionally, the flow slowed down the development of the frozen curtain area and the frozen curtain thickness. The larger the flow velocity, the greater the inhibition of the flow on the development of the frozen curtain. The test results can provide more references for the design and construction of freezing engineering with flowing groundwater.

Influence of Collagen Status on Microstructures of Porous Collagen/TCP Composites

2007 ◽  
Vol 330-332 ◽  
pp. 495-498
Author(s):  
Chao Zou ◽  
Wen Jian Weng ◽  
Xu Liang Deng ◽  
Kui Cheng ◽  
Pi Yi Du ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Cell Growth ◽  
Tricalcium Phosphate ◽  
Freeze Drying ◽  
Alkali Treatment ◽  
Test Results ◽  
Collagen Matrices ◽  
The Difference ◽  
Porous Composites ◽  
Better Than

Two starting collagens, sponge and floc collagen, were used to prepare collagen/tricalcium phosphate (TCP) composites. The resulting composites were porous and had 200μm pore size. However, there was a difference in the microstructure of the pore walls for the composites derived from the two collagens, the pore walls in sponge collagen/TCP composite were still porous and had 200 nm micropores size, TCP particles were trapped in collagen matrices. While floc collagen/TCP composite had smooth and dense walls in which TCP particles were embedded. The difference could be attributed to the starting collagen with different status. Sponge collagen has a soft structure, which easily becomes disassembled fibrils during alkali treatment, the disassembled fibrils are integrated again to form a dense morphology for pore walls after freeze-drying. While floc collagen has already a low disassembly degree, the alkali treatment could not be able to separate the fibrils, this remains as micropores in pore walls after freeze-drying. Both porous composites are significant in bone tissue engineering or regeneration. MTT test results showed the two composites had good cytocompatibility, and sponge collagen/TCP composite was somewhat better than floc collagen/TCP composite, which could result from that micropores derived roughness in pore walls of sponge collagen/TCP composite is suitable for cell growth.

Reply to comments of D. H. Zeuch

1992 ◽  
Vol 7 (7) ◽  
pp. 1959-1960
Author(s):  
Hu Gengxiang ◽  
Chen Shipu ◽  
Wu Xiaohua ◽  
Chen Xiaofu
Keyword(s):  
Compression Test ◽  
Compression Testing ◽  
Width Ratio ◽  
Test Results ◽  
Specimen Length ◽  
The Difference

Compression test results of our research on Al3Ti-base alloys are reported. It is evident that the specimen length-to-width ratio we used for compression testing can significantly reflect the difference in ductility of different alloys. Thus the tests fulfilled the aim of our present research.

scholarly journals Motion correction for routine X-ray lung CT imaging

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Doil Kim ◽  
Jiyoung Choi ◽  
Duhgoon Lee ◽  
Hyesun Kim ◽  
Jiyoung Jung ◽  
...  
Keyword(s):  
Motion Estimation ◽  
Motion Correction ◽  
Ct Imaging ◽  
Motion Artifacts ◽  
Ct Scans ◽  
Breath Hold ◽  
X Ray ◽  
Wide Range ◽  
Thorax Ct ◽  
Lung Ct

AbstractA novel motion correction algorithm for X-ray lung CT imaging has been developed recently. It was designed to perform for routine chest or thorax CT scans without gating, namely axial or helical scans with pitch around 1.0. The algorithm makes use of two conjugate partial angle reconstruction images for motion estimation via non-rigid registration which is followed by a motion compensated reconstruction. Differently from other conventional approaches, no segmentation is adopted in motion estimation. This makes motion estimation of various fine lung structures possible. The aim of this study is to explore the performance of the proposed method in correcting the lung motion artifacts which arise even under routine CT scans with breath-hold. The artifacts are known to mimic various lung diseases, so it is of great interest to address the problem. For that purpose, a moving phantom experiment and clinical study (seven cases) were conducted. We selected the entropy and positivity as figure of merits to compare the reconstructed images before and after the motion correction. Results of both phantom and clinical studies showed a statistically significant improvement by the proposed method, namely up to 53.6% (p < 0.05) and up to 35.5% (p < 0.05) improvement by means of the positivity measure, respectively. Images of the proposed method show significantly reduced motion artifacts of various lung structures such as lung parenchyma, pulmonary vessels, and airways which are prominent in FBP images. Results of two exemplary cases also showed great potential of the proposed method in correcting motion artifacts of the aorta which is known to mimic aortic dissection. Compared to other approaches, the proposed method provides an excellent performance and a fully automatic workflow. In addition, it has a great potential to handle motions in wide range of organs such as lung structures and the aorta. We expect that this would pave a way toward innovations in chest and thorax CT imaging.

Two important bridges protected from earthquake by extremely big sliding pendulum isolators

2021 ◽  
Author(s):  
Agostino Marioni ◽  
Roberto Dalpedri ◽  
Marco Banfi ◽  
Carla Cai
Keyword(s):  
Load Capacity ◽  
Special Focus ◽  
South East Asia ◽  
Vertical Load ◽  
Test Results ◽  
Surface Type ◽  
Total Length ◽  
Padma River ◽  
The Difference ◽  
Under Construction

<p>The Padma Bridge is a multipurpose road-rail bridge across the Padma River currently under construction in Bangladesh and is one of the most important projects in the whole south east Asia with a total length of 6150 m. The maximum design vertical load reaches 98725 kN.</p><p>The Holtekamp Bridge is a steel road bridge with 2 main spans of 150 m and 2 lateral spans of 75 for a total length of 450 m. The bridge is isolated by use of sliding pendulum isolators having a maximum vertical load capacity at ULS of 54915 kN.</p><p>In both cases the isolators are double sliding surface type but with a different approach about the central articulation. The paper aims to put in evidence the difference in behaviour of the 2 types of pendulum, analysing both the theoretical approach and the test results with a special focus over the adopted solution for perform the test on a device which exceed the capacity of aby existing laboratory.</p>

Accuracy of Computed Tomography for Detection of COVID-19 among Suspected Patients

2021 ◽  
Vol 15 (9) ◽  
pp. 2474-2476
Author(s):  
Maham Munir Awan ◽  
Afshan Noreen ◽  
Farah Kalsoom ◽  
Muhammad Tahir ◽  
Umaima Majeed ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Predictive Value ◽  
Gold Standard ◽  
Radiology Department ◽  
True Positive ◽  
Test Results ◽  
Rt Pcr ◽  
Radiological Society ◽  
Medical University ◽  
Pcr Test

Objective: To determine the accuracy of CT chest in diagnosis of COVID-19 taking RT-PCR-testing as gold standard. Materials and Methods: A total of 150 patients of suspicion of COVID-19 who were referred for CT Chest in Radiology Department of Nishtar Medical University Multan from June-2020 to May-2021 were included. In all patients, two RT-PCR test results were obtained with 7 days of admission in hospital. Presence of any of these positive was labelled as COVID-19 infection. CT chest was performed in all patients within 2 days of admission in hospital using 128 slices CT scan machine. The diagnosis of COVID-19 infection was made according to the recommendations by Radiological Society of North America (RSNA) protocol. Results: Mean age was 51.3±14.7 years. 78 (52%) patients were male and 72 (48%) patients were female. RTPCR test was positive in 89 (59.3%) patients. While the CT chest findings were suggestive of COVID-19 infection in 130 (86.7%) patients. The sensitivity of CT chest was 95.5%, specificity 26.2%, PPV wad 65.4% and NPV was 80.0%. Conclusion: CT chest has a very good sensitivity for detection of COVID-19, it can be used as a rapid diagnostic tool especially in areas of pandemic. However, the specificity of CT chest is low, that can limit its use in low COVID-19 affected areas. Keywords: COVID-19, Computed tomography, False Positive, True Positive, Positive Predictive Value, Negative Predictive Value.

Moving to e-bidding

2019 ◽  
Vol 24 (1) ◽  
pp. 2-18 ◽  
Author(s):  
Djoen San Santoso ◽  
Nuttapon Bourpanus
Keyword(s):  
Wilcoxon Test ◽  
Test Results ◽  
Public Infrastructure ◽  
Senior Managers ◽  
Content Type ◽  
Thai Government ◽  
Infrastructure Project ◽  
The Difference ◽  
Public Money ◽  
Mean Differences

Purpose This study aims to examine the influences of shifting the bidding system of Thai public infrastructure projects from e-auction to e-bidding. Design/methodology/approach A questionnaire survey was conducted with owners or senior managers with direct responsibility in deciding the mark-up of 72 small and medium-sized contractor firms. Five senior professionals were interviewed to provide insights into and to strengthen the discussion of the findings. The Wilcoxon test was applied to analyze the difference in the importance of the factors between e-auction and e-bidding. Findings The results revealed a shift in the importance of the factors, from those related to the financial aspects in the e-auction to the situational aspects in the e-bidding. The comparison test results also suggested that the majority of factors become significantly less important in the e-bidding system, with “identity of competitors” and “general expense of the bidding process” having the most apparent mean differences. The interview results supported by data on winning prices and estimations strongly indicated that bid collusions likely exist in the e-auction. By shifting to e-bidding, the data also show that the Thai Government can save public money in its infrastructure project development. Originality/value The study provides an analysis from the perspectives of contractor firms on how e-auction and e-bidding options influence bid mark-up decisions. Many studies have focused on the issues and advantages provided by the e-procurement mainly from the owner (government)’s perspective but how the change influences the contractor’s attitude has been less explored.

Sign in / Sign up

Export Citation Format

Share Document