Simulation Research on Post-Injection of Electronically Controlled Heavy-Duty Diesel Engine

2011 ◽  
Vol 121-126 ◽  
pp. 2238-2242
Author(s):  
Ming Hai Li ◽  
Feng Jiang ◽  
Biao Liu ◽  
Ming Gao Ouyang
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Process ◽  
Pressure Rise ◽  
Injection System ◽  
Post Injection ◽  
Simulation Research ◽  
Di Diesel Engine ◽  
Heavy Duty Diesel

GT-Suite software is used to establish the simulation model of electronic fuel injection system for 16V280ZJ diesel engine. Combustion process simulation calculation is conducted to the direct injection (DI) diesel engine based on a main-post double injection scheme. Simulation parameters are modified based on the comparison with given experimental results. The calculation results effectively reflect the influence of fuel ratio and the interval angle between main and post injection over emission and fuel economy. Finally, in order to improve the engine emissions and reduce the pressure rise rate, we get the optimal injection solution for the main-post injection mode.

Combustion and Emission Characteristics of Direct-Injection Compression Ignition Engines by Means of Two-Stage Split and Early Fuel Injection

2002 ◽  
Vol 124 (3) ◽  
pp. 660-667 ◽  
Author(s):  
K. Yamane ◽  
Y. Shimamoto
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Emission Characteristics ◽  
Diesel Combustion ◽  
Compression Ignition ◽  
Two Stage ◽  
Di Diesel Engine ◽  
Early Injection

The objective of this study was to experimentally clarify the effect of two-stage split and early injection on the combustion and emission characteristics of a direct-injection (DI) diesel engine. Engine tests were carried out using a single-cylinder high-speed DI diesel engine and an injection system, combining an ordinary jerk pump and an electronically controlled high-pressure injection system, KD-3. In these experiments to compare the combustion and exhaust emission characteristics with two-stage split and early injection, a single-stage and early injection was tested. The FT-IR exhaust-gas analyzer simultaneously measured the exhaust emissions of 26 components. The results showed that HCHO, CH3CHO, and CH3COOH were emitted during the very early stage of both single injection and two-stage injection. These concentrations were higher than those from diesel combustion with ordinary fuel injection timings. These exhaust emissions are characteristic components of combustion by premixed compression ignition with extremely early injection. In particular, the HCHO concentration in exhaust was reduced with an increase in the maximum rate of heat release after cool flame due to pre-reaction of pre-mixture. At extremely early injection, the NOx concentration was extremely low; however, the indicated specific fuel consumption (ISFC) was higher than that of ordinary diesel combustion. In the case of two-stage injection, the degree of constant volume is increased, so that ISFC is improved. These results also demonstrated the possibility of reducing HCHO, NOx, and smoke emissions by means of two-stage split and early injection.

scholarly journals Investigation into the effect of different fuels on ignition delay of M-type diesel combustion process

2008 ◽  
Vol 12 (1) ◽  
pp. 103-114 ◽  
Author(s):  
Dzevad Bibic ◽  
Ivan Filipovic ◽  
Ales Hribernik ◽  
Boran Pikula
Keyword(s):  
Diesel Engine ◽  
Ignition Delay ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection System ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Injection Angle ◽  
Start Of Injection

An ignition delay is a very complex process which depends on a great number of parameters. In practice, definition of the ignition delay is based on the use of correlation expressions. However, the correlation expressions have very often limited application field. This paper presents a new correlation which has been developed during the research project on the direct injection M-type diesel engine using both the diesel and biodiesel fuel, as well as different values of a static injection timing. A dynamic start of injection, as well as the ignition delay, is defined in two ways. The first approach is based on measurement of a needle lift, while the second is based on measurement of a fuel pressure before the injector. The latter approach requires calculation of pressure signals delay through the fuel injection system and the variation of a static advance injection angle changing. The start of a combustion and the end of the ignition delay is defined on the basis of measurements of an in-cylinder pressure and its point of separation from a skip-fire pressure trace. The developed correlation gives better prediction of the ignition delay definition for the M-type direct injection diesel engine in the case of diesel and biodiesel fuel use when compared with the classic expression by the other authors available in the literature.

scholarly journals Detailed Injection Strategy Analysis of a Heavy-Duty Diesel Engine Running on Rape Methyl Ester

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3717
Author(s):  
Nikita Zuev ◽  
Andrey Kozlov ◽  
Alexey Terenchenko ◽  
Kirill Karpukhin ◽  
Ulugbek Azimov
Keyword(s):  
Fuel Injection ◽  
Combustion Process ◽  
Pressure Rise ◽  
Base Case ◽  
Biodiesel Fuel ◽  
Pilot Injection ◽  
Post Injection ◽  
Heavy Duty ◽  
Injection Strategy ◽  
Fuel Mass

Using biodiesel fuel in diesel engines for heavy-duty transport is important to meet the stringent emission regulations. Biodiesel is an oxygenated fuel and its physical and chemical properties are close to diesel fuel, yet there is still a need to analyze and tune the fuel injection parameters to optimize the combustion process and emissions. A four-injections strategy was used: two pilots, one main and one post injection. A highly advanced SOI decreases the NOx and the compression work but makes the combustion process less efficient. The pilot injection fuel mass influences the combustion only at injection close to the top dead center during the compression stroke. The post injection has no influence on the compression work, only on the emissions and the indicated work. An optimal injection strategy was found to be: pilot SOI 19.2 CAD BTDC, pilot injection fuel mass 25.4%; main SOI 3.7 CAD BTDC, main injection fuel mass 67.3% mg; post SOI 2 CAD ATDC, post injection fuel mass 7.3% (the injection fuel mass is given as a percentage of the total fuel mass injected). This allows the indicated work near the base case level to be maintained, the pressure rise rate to decrease by 20% and NOx emissions to decrease by 10%, but leads to a 5% increase in PM emissions.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

A High-Speed Direct Injection Diesel Engine for Passenger Cars

1988 ◽  
Vol 202 (3) ◽  
pp. 171-181 ◽  
Author(s):  
J A Stephenson ◽  
B A Hood
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Passenger Cars ◽  
Medium Speed ◽  
Medium Speed Engine ◽  
Hsdi Diesel Engine ◽  
Wide Speed Range

The paper describes the development of a high-speed direct injection (HSDI) diesel engine suitable for passenger car applications. The evolution from a low emissions medium-speed engine, through a four-cylinder 2.3 litre research engine, into a four-cylinder 2.0 litre production engine is presented. The challenge to the engineer has been to develop the HSDI engine to operate with acceptable noise, emissions, smoke and driveability over the wide speed range (up to 5000 r/min) required for passenger cars. The key element in this task was the optimization of the combustion system and fuel injection equipment. The HSDI is shown to have a significant fuel economy advantage over the prechamber indirect injection (IDI) engine. Future developments of the fuel injection system are described which will further enhance the HSDI engine and provide additional noise and emissions control.

A Numerical Study of NOx Reduction for a DI Diesel Engine With Complex Geometry

2004 ◽  
Vol 126 (1) ◽  
pp. 13-20 ◽  
Author(s):  
Renshan Liu ◽  
Chao Zhang
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Complex Geometry ◽  
Numerical Study ◽  
Direct Injection ◽  
Nox Reduction ◽  
Geometrical Parameters ◽  
Injection Timing ◽  
Di Diesel Engine

A numerical study of NOx reduction for a Direct Injection (DI) Diesel engine with complex geometry, which includes intake/exhaust ports and moving valves, was carried out using the commercial computational fluid dynamics software KIVA-3v. The numerical simulations were conducted to investigate the effects of engine operating and geometrical parameters, including fuel injection timing, fuel injection duration, and piston bowl depth, on the NOx formation and the thermal efficiency of the DI Diesel engine. The tradeoff relationships between the reduction in NOx and the decrease in thermal efficiency were established.

Sign in / Sign up

Export Citation Format

Share Document