Research on Properties of Amorphous Cr-C Alloy Coating in Crystallization Evolution

2012 ◽  
Vol 184-185 ◽  
pp. 1175-1180
Author(s):  
Guo Liang Li ◽  
Xiao Hua Jie ◽  
Bi Xue Yang
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Intermetallic Compound ◽  
Adhesion Force ◽  
Alloy Coating ◽  
Treatment Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Proper Values ◽  
Peak Value

Amorphous Cr–C alloy coating was prepared by electrodepositing. The microhardness of the coating was tested after annealing from 100°C to 800°C and the crystallization evolution was studied by the analysis of X-ray diffraction (XRD) and differential scanning caborimetry (DSC). The results showed that the crystallization evolution of the coating began at 300°C and finished around 450°C, and intermetallic compound Cr7C3and Cr23C6appeared when heat treatment temperature reached around 600°C. The microhardness, corrosion resistance as well as the adhesion of the coating all increased first with the temperature and then dropped until it attained the proper values. The microhardness reached the maximum of 1610HV0.025at 600°C. While the corrosion resistance and the adhesion force attained the peak value at about 400°C.

scholarly journals Influence of Different Heat Treatment Temperatures on the Microstructure, Corrosion, and Mechanical Properties Behavior of Fe-Based Amorphous/Nanocrystalline Coatings

Coatings ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 858
Author(s):  
Shenglin Liu ◽  
Yongsheng Zhu ◽  
Xinyue Lai ◽  
Xueping Zheng ◽  
Runnan Jia ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Heat Treatment Temperature ◽  
Annealing Treatment ◽  
Treatment Temperature ◽  
X Ray Diffraction ◽  
Crystalline Phases ◽  
X Ray ◽  
Different Temperatures ◽  
Sprayed Coating

Fe-based amorphous/nanocrystalline coatings with smooth, compact interior structure and low porosity were fabricated via supersonic plasma spraying (SPS). The coatings showed outstanding corrosion resistance in a 3.5% NaCl solution at room temperature. In order to analyze the effect of annealing treatment on the microstructure, corrosion resistance and microhardness, the as-sprayed coating was annealed for 1 h under different temperatures such as 350, 450, 550 and 650 °C, respectively. The results showed that the number of oxides and cracks in the coatings presented an obvious increase with increasing annealing temperature, and the corrosion resistance of the coatings showed an obvious reduction. However, the microhardness of coatings showed an important increase. The microhardness of the coating could reach 1018 HV when the heat treatment temperature reached 650 °C. The X-ray diffraction (XRD) results showed that there appeared a number of crystalline phases in the coating when the heat treatment temperature was at 650 °C. The crystalline phases led to the increase of the microhardness.

In Situ X-Ray Diffraction Studies of Crystallization Growth Behavior in ZnO-Bi2O3-B2O3 Glass as a Route to Functional Optical Devices

MRS Advances ◽  
2018 ◽  
Vol 3 (11) ◽  
pp. 563-567 ◽  
Author(s):  
Quentin Altemose ◽  
Katrina Raichle ◽  
Brittani Schnable ◽  
Casey Schwarz ◽  
Myungkoo Kang ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Glass Ceramics ◽  
Treatment Temperature ◽  
Crystal Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
In Situ Xrd ◽  
Dsc Measurements ◽  
Transmission Window

ABSTRACTTransparent optical ZnO–Bi2O3–B2O3 (ZBB) glass-ceramics were created by the melt quenching technique. In this work, a melt of the glass containing stoichiometric ratios of Zn/Bi/B and As was studied. Differential scanning calorimeter (DSC) measurements was used to measure the thermal behavior. VIS/NIR transmission measurements were used to determine the transmission window. X-ray diffraction (XRD) was used to determine crystal phase. In this study, we explore new techniques and report a detailed study of in-situ XRD of the ZBB composition in order to correlate nucleation temperature, heat treatment temperature, and heat treatment duration with induced crystal phase.

EFFECT OF HEAT TREATMENT ON MICROSTRUCTURE AND CORROSION RESISTANCE OF Ni-B-W-Mo COATING DEPOSITED BY ELECTROLESS METHOD

2018 ◽  
Vol 25 (08) ◽  
pp. 1950023 ◽  
Author(s):  
ARKADEB MUKHOPADHYAY ◽  
TAPAN KUMAR BARMAN ◽  
PRASANTA SAHOO
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Electrochemical Techniques ◽  
Sodium Molybdate ◽  
Medium Carbon Steel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solid Solution Strengthening ◽  
Heat Treated ◽  
Electroless Coatings

The present work reports the deposition of a quaternary Ni-B-W-Mo coating on AISI 1040 medium carbon steel and its characterization. Quaternary deposits are obtained by suitably modifying existing electroless Ni-B bath. Composition of the as-deposited coating is analyzed by energy dispersive X-ray spectroscopy. The structural aspects of the as-deposited and coatings heat treated at 300[Formula: see text]C, 350[Formula: see text]C, 400[Formula: see text]C, 450[Formula: see text]C and 500[Formula: see text]C are determined using X-ray diffraction technique. Surface of the as-deposited and heat-treated coatings is examined using a scanning electron microscope. Very high W deposition could be observed when sodium molybdate is present in the borohydride-based bath along with sodium tungstate. The coatings in their as-deposited condition are amorphous while crystallization takes place on heat treatment. A nodulated surface morphology of the deposits is also observed. Vickers’ microhardness and crystallite size measurement reveal inclusion of W and Mo results in enhanced thermal stability of the coatings. Solid solution strengthening of the electroless coatings by W and Mo is also observed. The applicability of kinetic strength theory to the hardening of the coatings on heat treatment is also investigated. Corrosion resistance of Ni-B-W-Mo coatings and effect of heat treatment on the same are also determined by electrochemical techniques.

Synthesis and Properties of Electroless Ni-P-W/Nano-Al2O3 Composite Coatings Deposited on Sintered NdFeB Permanent Magnet

2011 ◽  
Vol 306-307 ◽  
pp. 901-906 ◽  
Author(s):  
Huan Ming Chen ◽  
Ya Hong Gao ◽  
Qiong Lv ◽  
Dong Yang ◽  
Xin Xin Lin
Keyword(s):  
Corrosion Resistance ◽  
Permanent Magnet ◽  
Composite Coatings ◽  
Alloy Coating ◽  
X Ray Diffraction ◽  
Ndfeb Magnet ◽  
X Ray ◽  
Plating Method ◽  
Ndfeb Permanent Magnet ◽  
Electroless Ni

The Ni-P-W/nano-Al2O3composite coatings were deposited on the surface of sintered NdFeB permanent magnet by electroless plating method. The morphology and the phases of Ni-P-W/nano-Al2O3composite coatings were investigated using scanning electron microscopy and X-ray diffraction respectively. The hardness and the corrosion resistance of the composite coatings were also tested. The results indicated that the composite coatings morphology appears closely nodules morphology, and the microhardness increases with increasing incorporation of Al2O3ratio. Compared with NdFeB magnet and Ni-P-W alloy coatings, the corrosion resistance of the composite coatings was superior to that of the NdFeB magnet and the alloy coating obviously.

Neodymium Incorporation in Zirconolite-Based Glass-Ceramics

2000 ◽  
Vol 663 ◽  
Author(s):  
P. Loiseau ◽  
D. Caurant ◽  
N. Baffier ◽  
C. Fillet
Keyword(s):  
Heat Treatment ◽  
Glass Ceramics ◽  
Fission Products ◽  
Treatment Temperature ◽  
Spent Fuel ◽  
X Ray Diffraction ◽  
Parent Glass ◽  
X Ray ◽  
Spin Resonance

ABSTRACTThe investigations on enhanced reprocessing of nuclear spent fuel, and notably on separating the long-lived minor actinides, such as Am and Cm, from the other fission products have led to the development of highly durable specific matrices such as glass-ceramics for their immobilization. This study deals with the characterization of zirconolite (CaZrTi2O7) based glass-ceramics synthesized by devitrification of an aluminosilicate parent glass. Trivalent actinide ions were simulated by neodymium, which is a paramagnetic local probe. Glass-ceramics with Nd2O3 contents ranging from 0 to 10 weight % were prepared by heat treatment of a parent glass at two different growth temperatures: 1050° and 1200°C. X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX) and electron spin resonance (ESR) measurements clearly indicate that Nd3+ ions are partly incorporated in zirconolite crystals formed in the bulk of the glass-ceramic samples. The amount of neodymium in the crystalline phase was estimated using ESR results and was found to decrease with increasing either heat treatment temperature or total Nd2O3 content.

Preparation and Catalytic Performance of Ti(SO4)2/γ-Al2O3 Catalysts for Oligomerization of 1-Butene

2013 ◽  
Vol 634-638 ◽  
pp. 696-700
Author(s):  
Lin Jiu Xiao ◽  
Peng Li ◽  
Yong Gang Sheng
Keyword(s):  
Heat Treatment ◽  
Physicochemical Properties ◽  
Heat Treatment Temperature ◽  
Catalytic Performance ◽  
Treatment Temperature ◽  
Impregnation Method ◽  
X Ray Diffraction ◽  
Isothermal Adsorption ◽  
X Ray ◽  
Adsorption Desorption

A series of Ti(SO4)2/γ-Al2O3 catalysts were prepared by impregnation method and the catalytic performance of these catalysts in 1-butene oligomerization was investigated. The heat treatment temperature played great influences on the catalytic performance of these catalysts in the oligomerization. 90.1 wt.% conversion of 1-butene and 92.2 wt.% selectivity of dimers were obtained on Ti(SO4)2/γ-Al2O3(450) catalyst at 80 °C, 1.0 Mpa and LHSV=0.6 h−1. The heat treatment temperature determined the crystallinity of TiOSO4 and specific surface area of these catalysts, which affected the catalytic performance of these catalysts in 1-butene oligomerization. In addition, the physicochemical properties of these catalysts were comparatively characterized by powder X-ray diffraction (XRD), N2 isothermal adsorption-desorption techniques.

Research on Preparation and Properties of Al-Mn Alloy Coating in NaCl-KCl-AlCl3-NdCl3 Molten Salts

2011 ◽  
Vol 121-126 ◽  
pp. 335-339
Author(s):  
Xian Jin Yu ◽  
Li Peng Zhang ◽  
Zhi Wei Ge ◽  
Yun Hui Dong ◽  
Dang Gang Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Corrosion Resistance ◽  
Molten Salts ◽  
Alloy Coating ◽  
Surface Coatings ◽  
X Ray Diffraction ◽  
Pitting Potential ◽  
X Ray ◽  
Scanning Electron

Al-Mn alloy coatings were electrodeposited on an iron substrate from AlCl3-NaCl-KCl low-temperature molten salts with anhydrous MnCl2 enhanced by the addition of NdCl3.The microstructure and properties of the Al-Mn alloy coatings were investigated, and scanning electron microscopy, X-ray diffraction, and polarization curves were used to determine the composition, surface morphology, phase structure, and corrosion resistance of the obtained deposits. The results show that the surface coatings were smooth, and that the crystallites were dense and uniform when 0.23 wt% NdCl3 was added to the molten salt. An amorphous mixture of Al and Al6Mn was obtained. NdCl3 enhanced the corrosion resistance and increased the hardness of the single amorphous phase alloys. The pitting potential of the coating was approximately −1.04V, and its hardness was 392 kgf/mm2.

Characterization of Ni-P and Ni-P-Al2O3 Heat Treated Layers

2017 ◽  
Vol 1143 ◽  
pp. 26-31
Author(s):  
Lucica Balint ◽  
Gina Genoveva Istrate
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Corrosion Resistance ◽  
Composite Coatings ◽  
Treatment Temperature ◽  
Initial State ◽  
X Ray ◽  
Transmission Electron ◽  
Heat Treated ◽  
Before And After

Research has shown the relationship among hardness, usage and corrosion resistance Ni-P-Al2O3 composite coatings on steel support heat treated. The electroless strips were heat treated at 200°C, 300°C, 400°C, 500°C and 600°C. Further studies on corrosion, hardness and usage revealed changes in properties, compared to the initial state, both on the strips coated with Ni-P and the ones coated with Ni-P-Al2O3 composite. The samples have been studied before and after the heat treatment via Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Energy Dispersive X-ray Analysis (EDX) and X-Ray Diffraction (XRD). The results show that untreated Ni-P layers exhibit strong corrosion resistance, while hardness and usage increase with heat treatment temperature, with a peak at 400 °C. Using suspended particles co-deposition, led to new types of layers, some with excellent hardness and usage properties. Corrosion resistance increase with heat treatment. Coating layers can be adjusted to the desired characteristics, by selecting proper parameters for the expected specific results.

Effect of Heat Treatment on Microstructure and Corrosion Resistance of Ni-Cr-Mo-Fe Alloys

2012 ◽  
Vol 581-582 ◽  
pp. 773-776
Author(s):  
Er Chao Ding ◽  
Zhen Yong Man ◽  
Xin Xin Yang ◽  
Jing Tai Zhao
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Electrochemical Analysis ◽  
X Ray Diffraction ◽  
Homogeneous Microstructure ◽  
X Ray ◽  
Arc Melting ◽  
Distribution Of Elements ◽  
Microstructure Morphology ◽  
Fe Alloys

The effects of heat treatment on microstructure and corrosion resistance of Ni-Cr-Mo-Fe nickel-based alloys were investigated by X-ray diffraction (XRD), metallographic microscope (MM), scanning electron microscopy (SEM) and electrochemical analysis, respectively. Experimental results indicated that the samples which were prepared via electric arc melting shielded by argon were pure solid solutions with homogeneous microstructure. Segregation of chromium element and slightly smaller grain size were found after heat treatment. Better corrosion resistance of samples was achieved after heat treatment, due to improvement of microstructure, morphology and distribution of elements.

Morphology of Carbon Micro-Coils

2004 ◽  
Vol 449-452 ◽  
pp. 205-208
Author(s):  
M. Fujii ◽  
S. Motojima
Keyword(s):  
Heat Treatment ◽  
Lattice Structure ◽  
Diffraction Method ◽  
Chemical Vapor ◽  
Amorphous Structure ◽  
Treatment Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Higher Temperature

The double helical carbon micro-coils were obtained by chemical vapor deposition. As-grown carbon micro-coils with amorphous structure were heat-treated at various temperatures up to 3000°C . By heat treatment, the shape of the coils was not changed. The morphology of these coils was observed in detail using electron microscope. The lattice structure was analyzed by X-ray diffraction method. Heat treatment temperature dependence of the magnetoresistance and the measurement of Raman spectra suggest that the coils heattreated at higher temperature are more highly graphitized.

Sign in / Sign up

Export Citation Format

Share Document