Research into the Preparation and Performance of Hydrotalcite/ MC Nylon 6 by In Situ Intercalation Polymerization

2013 ◽  
Vol 295-298 ◽  
pp. 426-429 ◽  
Author(s):  
Bo Fen Huang ◽  
Han Xuan Liang ◽  
Yan Chao Bai ◽  
Jun Jie Wang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Nylon 6 ◽  
Izod Impact ◽  
Obvious Phase Separation ◽  
And Performance ◽  
Mechanical Properties Characterization ◽  
Intercalation Polymerization

Hydrotalcite (LDHs) / MC nylon 6 composites were prepared by in- situ intercalation polymerization, followed by morphology and mechanical properties’ characterization of composites. FTIR shows that chemical structure of the molecular chain of the MC nylon 6 is not changed with adding hydrotalcite; SEM reveales that LDHs (2.5, wt-%) has good dispersion and compatibility in the MC nylon 6 matrixes; but when the amount of LDHs is excessive, the composites show obvious phase separation phenomenon. Hydrotalcite can significantly improve the mechanical properties of the composites. When the amount of hydrotalcite reaches 2.5% (wt-%), the composite has best comprehensive mechanical performance. Comparing with untreated MCPA6, the tensile strength and notched Izod impact strength are respectively increased by 68 % and 53 %.

scholarly journals Design and Characterization of Microscale Auxetic and Anisotropic Structures Fabricated by Multiphoton Lithography

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 446
Author(s):  
Ioannis Spanos ◽  
Zacharias Vangelatos ◽  
Costas Grigoropoulos ◽  
Maria Farsari
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Mechanical Performance ◽  
Element Analysis ◽  
Mechanical Responses ◽  
Multiphoton Lithography ◽  
Anisotropic Structures ◽  
Scanning Electron

The need for control of the elastic properties of architected materials has been accentuated due to the advances in modelling and characterization. Among the plethora of unconventional mechanical responses, controlled anisotropy and auxeticity have been promulgated as a new avenue in bioengineering applications. This paper aims to delineate the mechanical performance of characteristic auxetic and anisotropic designs fabricated by multiphoton lithography. Through finite element analysis the distinct responses of representative topologies are conveyed. In addition, nanoindentation experiments observed in-situ through scanning electron microscopy enable the validation of the modeling and the observation of the anisotropic or auxetic phenomena. Our results herald how these categories of architected materials can be investigated at the microscale.

Characterization of the Aniline.DBSA/Thermoplastic Polyurethane Blends for the Thermo-Mechanical and Electro-Mechanical Properties

2021 ◽  
Vol 875 ◽  
pp. 96-103
Author(s):  
Ayesha Afzal ◽  
Iqra Abdul Rashid ◽  
H.M. Faizan Shakir ◽  
Asra Tariq
Keyword(s):  
Mechanical Properties ◽  
Thermoplastic Polyurethane ◽  
Strain Sensors ◽  
Sem Images ◽  
Dynamic Mechanical Thermal Analyzer ◽  
Thermal Analyzer ◽  
Uniform Dispersion ◽  
Polymerization Method

Conducting polymer blends Polyaniline-Dodecylbenzene sulfonic acid (Pani.DBSA) and thermoplastic polyurethane (TPU) were prepared using in-situ emulsion polymerization method by dissolving both components in DMF. Ani.DBSA/TPU blends were prepared with different compositions 20/80, 30/70, 40/60 and 50/50 wt%. Theses blends have good conducting and mechanical properties. Blends were characterized by Potentiostate, Thermogravimetric analysis (TGA), Infrared spectroscopy (FTIR) and Dynamic mechanical thermal analyzer (DMTA). The electrical conductivity increases up to 30 wt% loading of aniline.DBSA after that it decreases gradually. The uniform dispersion of aniline.DBSA showed in SEM images which is the indication of a strong connection between aniline.DBSA and TPU which increase the conductivity. These blends can be used as strain sensors.

Preparation and Characterization of In Situ Nanocomposites of Graphene Nanosheets/Polyurethane

2019 ◽  
Vol 814 ◽  
pp. 90-95 ◽  
Author(s):  
Guang Lei Lv ◽  
Yuan Yuan Li ◽  
Chen Fei ◽  
Zhi Hao Shan ◽  
Jing Gan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Graphene Nanosheets ◽  
Graphene Sheets ◽  
Microstructural Properties ◽  
Wear Performance ◽  
Polyurethane Composites

Graphene nanosheets/polyurethane (GNS/PU) was prepared in situ by polymerization technique for the manufacture of PU safety shoes soles. The graphene nanosheets/polyurethane composites were characterized for their mechanical properties, thermal conductivity and abrasion resistance, and comparison is made with those of the neat polyurethane. The microstructural properties of GNS/PU were characterized by SEM. The results show that with the increase of the amount of graphene within the range of weight-percentages analyzed, the tensile strength of the composites gradually increases. The tensile strength of the GNS/PU composites increased to 64.14 MPa with 2 wt% GNS, compared with 55.1 MPa for neat PU. When the graphene sheets reached 2 wt%, the abrasion volume reached 71 mm3. Compared with the pure PU, the wear performance of GNS/PU composites was significantly improved.

scholarly journals Mechanical properties of boron nitride sheet with randomly distributed vacancy defects

2019 ◽  
Vol 8 (1) ◽  
pp. 210-217 ◽  
Author(s):  
Yingjing Liang ◽  
Hongfa Qin ◽  
Jianzhang Huang ◽  
Sha Huan ◽  
David Hui
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Performance Optimization ◽  
Fracture Strain ◽  
Mechanical Performance ◽  
Hexagonal Boron Nitride ◽  
Stable Configuration ◽  
Vacancy Defects ◽  
And Performance ◽  
Dynamics Simulations

Abstract Defects and temperature effects on the mechanical properties of hexagonal boron nitride sheet (h-BN) containing randomly distributed defects are investigated by molecular dynamics simulations and the reasons of the results are discussed. Results show that defect deteriorate the mechanical performance of BNNS. The mechanical properties are reduced by increasing percentage of vacancy defects including fracture strength, fracture strain and Young’s modulus. Simulations also indicate that the mechanical properties decrease with the temperature increasing. Moreover, defects affect the stable configuration at high temperature. With the percentage of defect increases the nanostructures become more and more unstable. Positions of the defect influent the mechanical properties. The higher the temperature and the percentage of defect are, the stronger the position of the randomly distributed defect affects the mechanical properties. The study provides a theoretical basis for the preparation and performance optimization of BNNSs.

A Novel In-Situ Nanoindentation Characterization of Phase Transforming Materials

2015 ◽  
Vol 1754 ◽  
pp. 19-24
Author(s):  
A. Alipour Skandani ◽  
R. Ctvrtlik ◽  
M. Al-Haik
Keyword(s):  
Mechanical Properties ◽  
Phase Transformation ◽  
Creep Compliance ◽  
Physical And Mechanical Properties ◽  
In Situ Methods ◽  
Negative Creep ◽  
Nanoindentation Instrument ◽  
Structural Instabilities

ABSTRACTMaterials with different allotropes can undergo one or more phase transformations based on the changes in the thermodynamic states. Each phase is stable in a certain temperature/pressure range and can possess different physical and mechanical properties compared to the other phases. The majority of material characterizations have been carried out for materials under equilibrium conditions where the material is stabilized in a certain phase and a lesser portion is devoted for onset of transformation. Alternatively, in situ measurements can be utilized to characterize materials while undergoing phase transformation. However, most of the in situ methods are aimed at measuring the physical properties such as dielectric constant, thermal/electrical conductivity and optical properties. Changes in material dimensions associated with phase transformation, makes direct measurement of the mechanical properties very challenging if not impossible. In this study a novel non-isothermal nanoindentation technique is introduced to directly measure the mechanical properties such as stiffness and creep compliance of a material at the phase transformation point. Single crystal ferroelectric triglycine sulfate (TGS) was synthetized and tested with this method using a temperature controlled nanoindentation instrument. The results reveal that the material, at the transformation point, exhibits structural instabilities such as negative stiffness and negative creep compliance which is in agreement with the findings of published works on the composites with ferroelectric inclusions.

Sign in / Sign up

Export Citation Format

Share Document