Automated FE Analysis for Heat Sink of LED Modules

2013 ◽  
Vol 302 ◽  
pp. 765-771 ◽  
Author(s):  
Joon Seong Lee ◽  
Dong Keun Park ◽  
Youn Jong Choi
Keyword(s):  
Heat Sink ◽  
Geometric Model ◽  
Three Dimensional ◽  
Fe Analysis ◽  
Present System ◽  
Analysis Model ◽  
Solid Geometry ◽  
Analysis System ◽  
Definition Of ◽  
Interactive Operations

This paper describes an automatic finite element (FE) mesh generation for FE analysis of LED modules. It is consisting of element generation, bubble packing and solid geometry modeler. This automated FE analysis system including bubble packing method consists of three sub-processes: (a) definition of geometric model, i.e. analysis model, (b) generation of bubbles, and (c) generation of elements. One of commercial solid modelers is employed for three-dimensional solid structures. Bubble is generated if its distance from existing bubble points is similar to the bubble spacing function at the point. The Delaunay method is introduced as a basic tool for element generation. The developed system allows designers to evaluate detailed physical behaviors of structures through some simple interactive operations to their geometry models. To demonstrate practical performances of the present system, the system was used to an analysis of heat sink. Practical performances of the present system are demonstrated through several examples for heat sink of LED modules.

An Automatic Technique for CAE Analysis With a 3D-CAD Model

2002 ◽  
Author(s):  
Norihiko Nonaka ◽  
Ichirou Nishigaki
Keyword(s):  
Computer Aided Design ◽  
Geometric Model ◽  
Three Dimensional ◽  
Analysis Time ◽  
Cad Model ◽  
3D Cad ◽  
Computer Aided ◽  
Cae Analysis ◽  
Analysis System ◽  
Definition Of

A CAE (computer-aided engineering) analysis system, consisting of a 3D-CAD (three-dimensional computer-aided design) modeler, a pre-processor, an analysis solver, and a post-processor, was developed. This system uses automated procedures for solid modeling, definition of analysis models (i.e., defining boundary conditions and material properties, traditionally done manually), mesh generation, numerical simulation, and visualization of results. The CAE analysis system has two key features: it can greatly reduce the analysis time, and it uses a 3D-CAD model as the geometric model for numerical analysis. It was found that the developed automatic system reduces the analysis time by 50% compared with that for manual operation.

scholarly journals Deterministic mathematical morphology for CAD/CAM

2014 ◽  
Vol 31 (7) ◽  
pp. 1221-1241 ◽  
Author(s):  
Rubén Sarabia-Pérez ◽  
Antonio Jimeno-Morenilla ◽  
Rafael Molina-Carmona
Keyword(s):  
Mathematical Morphology ◽  
Geometric Model ◽  
Three Dimensional ◽  
Morphological Operations ◽  
Basic Operation ◽  
Geometric Data Structures ◽  
Content Type ◽  
Morphological Operators ◽  
Cad Cam ◽  
Definition Of

Purpose – The purpose of this paper is to present a new geometric model based on the mathematical morphology paradigm, specialized to provide determinism to the classic morphological operations. The determinism is needed to model dynamic processes that require an order of application, as is the case for designing and manufacturing objects in CAD/CAM environments. Design/methodology/approach – The basic trajectory-based operation is the basis of the proposed morphological specialization. This operation allows the definition of morphological operators that obtain sequentially ordered sets of points from the boundary of the target objects, inexistent determinism in the classical morphological paradigm. From this basic operation, the complete set of morphological operators is redefined, incorporating the concept of boundary and determinism: trajectory-based erosion and dilation, and other morphological filtering operations. Findings – This new morphological framework allows the definition of complex three-dimensional objects, providing arithmetical support to generating machining trajectories, one of the most complex problems currently occurring in CAD/CAM. Originality/value – The model proposes the integration of the processes of design and manufacture, so that it avoids the problems of accuracy and integrity that present other classic geometric models that divide these processes in two phases. Furthermore, the morphological operative is based on points sets, so the geometric data structures and the operations are intrinsically simple and efficient. Another important value that no excessive computational resources are needed, because only the points in the boundary are processed.

Parallel Analysis of Incompressible Flow and Structure Interaction Using Partitioned Iterative Method

2012 ◽  
Author(s):  
Shunji Kataoka ◽  
Hiroshi Kawai ◽  
Satsuki Minami ◽  
Shinobu Yoshimura
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Analysis Model ◽  
Iterative Coupling ◽  
Structure Interaction ◽  
Large Scale Analysis ◽  
Coupling Approach ◽  
Analysis System ◽  
Partitioned Method ◽  
Partitioned Methods

Dynamic response considering fluid structure interaction (FSI) is crucial in many engineering fields and the numerical methods to solve the FSI problems are keenly demanded in engineering field. Generally coupled phenomena can be simulated in either monolithic or partitioned methods, however the application of FSI analysis are limited because of its calculation costs. The partitioned method is now focused because it can re-use the existing flow and structural analysis solver without elaborated modification and it gives the same accuracy when iterative coupling approach is taken. When the partitioned method combined with the existing flow and structure solver which can solve large-scale analysis model, it is expected to solve realistic three dimensional complex FSI problems in acceptable durations. In this work, the partitioned FSI analysis system are developed using existing flow and structure solvers. The system is applied to several validation models and accuracy and efficiency of the solver are shown.

scholarly journals Finite Element Modeling of Composite Concrete-Steel Columns / Numeryczne Modelowanie Zespolonych Słupów Stalowo-Betonowych

2011 ◽  
Vol 57 (4) ◽  
pp. 373-388 ◽  
Author(s):  
L. Kwasniewski ◽  
E. Szmigiera ◽  
M. Siennicki
Keyword(s):  
Finite Element ◽  
Experimental Testing ◽  
Three Dimensional ◽  
Fe Analysis ◽  
Finite Element Program ◽  
Steel Columns ◽  
Element Program ◽  
Definition Of ◽  
Deformation Modes ◽  
Predictive Study

Abstract This paper presents the numerical part of the research program on concrete-filled steel columns. Nonlinear, three dimensional FE analysis of axial compression, was conducted using the finite element program ABAQUS. The numerical results were validated through comparison with experimental data in terms of ultimate loading and deformation modes. Modeling related problems such as the definition of boundary conditions, imperfections, concrete-steel interaction, material representation and others are investigated using a comprehensive parametric study. The developed FE models will be used for an enhanced interpretation of experiments and for the predictive study of cases not included in the experimental testing.

Application of high-resolution field-emission LVSEM, backscatter imaging, immunogold staining to definition of the spatial distributions of two human neutrophil adherence receptors

1993 ◽  
Vol 51 ◽  
pp. 36-37
Author(s):  
Robert D. Nelson ◽  
Sharon R. Hasslen ◽  
Stanley L. Erlandsen
Keyword(s):  
Cell Surface ◽  
Surface Membrane ◽  
Three Dimensional ◽  
Human Neutrophils ◽  
Spatial Distributions ◽  
Immunogold Staining ◽  
Functional Control ◽  
Neutrophil Adherence ◽  
Definition Of ◽  
Mode Of Attachment

Receptors are commonly defined in terms of number per cell, affinity for ligand, chemical structure, mode of attachment to the cell surface, and mechanism of signal transduction. We propose to show that knowledge of spatial distribution of receptors on the cell surface can provide additional clues to their function and components of functional control.L-selectin and Mac-1 denote two receptor populations on the neutrophil surface that mediate neutrophil-endothelial cell adherence interactions and provide for targeting of neutrophil recruitment to sites of inflammation. We have studied the spatial distributions of these receptors using LVSEM and backscatter imaging of isolated human neutrophils stained with mouse anti-receptor (primary) antibody and goat anti-mouse (secondary) antibody conjugated to 12 nm colloidal gold. This combination of techniques provides for three-dimensional analysis of the expression of these receptors on different surface membrane domains of the neutrophil: the ruffles and microvilli that project from the cell surface, and the cell body between these projecting structures.

Pavement Damage Due to Conventional and New Generation of Wide-Base Super Single Tires

2005 ◽  
Vol 33 (4) ◽  
pp. 210-226 ◽  
Author(s):  
I. L. Al-Qadi ◽  
M. A. Elseifi ◽  
P. J. Yoo ◽  
I. Janajreh
Keyword(s):  
Carrying Capacity ◽  
Material Properties ◽  
Three Dimensional ◽  
Fe Analysis ◽  
Load Carrying Capacity ◽  
Inflation Pressure ◽  
3D Finite Element ◽  
Load Carrying ◽  
Pavement Damage ◽  
New Generation

Abstract The objective of this study was to quantify pavement damage due to a conventional (385/65R22.5) and a new generation of wide-base (445/50R22.5) tires using three-dimensional (3D) finite element (FE) analysis. The investigated new generation of wide-base tires has wider treads and greater load-carrying capacity than the conventional wide-base tire. In addition, the contact patch is less sensitive to loading and is especially designed to operate at 690kPa inflation pressure at 121km/hr speed for full load of 151kN tandem axle. The developed FE models simulated the tread sizes and applicable contact pressure for each tread and utilized laboratory-measured pavement material properties. In addition, the models were calibrated and properly validated using field-measured stresses and strains. Comparison was established between the two wide-base tire types and the dual-tire assembly. Results indicated that the 445/50R22.5 wide-base tire would cause more fatigue damage, approximately the same rutting damage and less surface-initiated top-down cracking than the conventional dual-tire assembly. On the other hand, the conventional 385/65R22.5 wide-base tire, which was introduced more than two decades ago, caused the most damage.

Modeling and experimental verification on directivity of an electret cell array loudspeaker

2012 ◽  
Vol 24 (3) ◽  
pp. 326-333 ◽  
Author(s):  
Yu-Chi Chen ◽  
Wen-Ching Ko ◽  
Han-Lung Chen ◽  
Hsu-Ching Liao ◽  
Wen-Jong Wu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Digital Control System ◽  
Analysis Model ◽  
Cell Array ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
The Finite Element Analysis ◽  
Directivity Characteristics

We propose a model to give us a method to investigate the characteristic three-dimensional directivity in an arbitrarily configured flexible electret-based loudspeaker. In recent years, novel electret loudspeakers have attracted much interest due to their being lightweight, paper thin, and possessing excellent mid- to high-frequency responses. Increasing or decreasing the directivity of an electret loudspeaker makes it excellent for adoption to many applications, especially for directing sound to a particular area or specific audio location. Herein, we detail a novel electret loudspeaker that possesses various directivities and is based on various structures of spacers instead of having to use multichannel amplifiers and a complicated digital control system. In order to study the directivity of an electret loudspeaker based on an array structure which can be adopted for various applications, the horizontal and vertical polar directivity characteristics as a function of frequency were simulated by a finite-element analysis model. To validate the finite-element analysis model, the beam pattern of the electret loudspeaker was measured in an anechoic room. Both the simulated and experimental results are detailed in this article to validate the various assertions related to the directivity of electret cell-based smart speakers.

scholarly journals Maneuverability of the Scope and Instruments within Three Different Single-Incision Laparoscopic Ports: An Experimental Pilot Study

Animals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1242
Author(s):  
Georg Haider ◽  
Ursula Schulz ◽  
Nikola Katic ◽  
Christian Peham ◽  
Gilles Dupré
Keyword(s):  
Motion Analysis ◽  
Single Incision ◽  
Single Port ◽  
Three Dimensional ◽  
Analysis Software ◽  
Port Access ◽  
Port System ◽  
Sils Port ◽  
Glove Port ◽  
Analysis System

Single-port access systems (SPASs) are currently used in human and veterinary surgeries. However, they pose technical challenges, such as instrument crowding, intra- and extracorporeal instrument collision, and reduced maneuverability. Studies comparing the maneuverability of the scopes and instruments in different SPASs are lacking. This study aimed to compare the maneuverability of three different SPASs: the Covidien SILS-port, Storz Endocone, and glove port. A clear acrylic box with artificial skin placed at the bottom was used to mimic the abdominal wall and cavity. The three SPASs were placed from below, and a 10-mm endoscope and 5-mm instrument were introduced. A motion analysis system consisting of 18 cameras and motion analysis software were used to track the movement of the endoscope and instrument, to determine the volume of the cone-shaped, three-dimensional figures over which movement was possible, with higher values indicating greater maneuverability. The Mann–Whitney U test was used for the analysis. The maneuverability of the endoscope alone was significantly higher in the glove port system than in the other two SPASs. When inserting an additional instrument, the maneuverability significantly decreased in the SILS-port and Endocone, but not in the glove port. The highest maneuverability overall was found in the glove port.

scholarly journals Proposing 3D Thermal Technology for Heritage Building Energy Monitoring

2021 ◽  
Vol 13 (8) ◽  
pp. 1537
Author(s):  
Antonio Adán ◽  
Víctor Pérez ◽  
José-Luis Vivancos ◽  
Carolina Aparicio-Fernández ◽  
Samuel A. Prieto
Keyword(s):  
Computer Vision ◽  
Dimensional Space ◽  
Three Dimensional ◽  
Building Energy ◽  
Energy Monitoring ◽  
3D Computer Vision ◽  
Building Monitoring ◽  
Heritage Buildings ◽  
Heritage Building ◽  
Definition Of

The energy monitoring of heritage buildings has, to date, been governed by methodologies and standards that have been defined in terms of sensors that record scalar magnitudes and that are placed in specific positions in the scene, thus recording only some of the values sampled in that space. In this paper, however, we present an alternative to the aforementioned technologies in the form of new sensors based on 3D computer vision that are able to record dense thermal information in a three-dimensional space. These thermal computer vision-based technologies (3D-TCV) entail a revision and updating of the current building energy monitoring methodologies. This paper provides a detailed definition of the most significant aspects of this new extended methodology and presents a case study showing the potential of 3D-TCV techniques and how they may complement current techniques. The results obtained lead us to believe that 3D computer vision can provide the field of building monitoring with a decisive boost, particularly in the case of heritage buildings.

A New Geometric Model of Laid-in Weft-Knitted Fabrics

2021 ◽  
pp. 004051752199276
Author(s):  
Ki Wai Fong ◽  
Si Qing Li ◽  
Rong Liu
Keyword(s):  
Cost Estimation ◽  
Geometric Model ◽  
Three Dimensional ◽  
Wearable Electronics ◽  
Material Consumption ◽  
Knitted Fabrics ◽  
Functional Textiles ◽  
Loop Pattern ◽  
Spatial Configurations ◽  
Consumption Prediction

Inlay yarn and laid-in structures are important technical knitting elements that have been increasingly applied in the structural design of functional textiles in industrial, medical, and wearable electronics fields. However, there is no currently established geometric model to numerically analyze their spatial morphologies and structural properties. This study presents a new geometric model and numerical analysis approach to characterize spatial configurations of inlay yarn and ground yarn in a three-dimensional scenario for laid-in weft-knitted fabrics. Loop lengths of the inlay and ground yarn materials were calculated and analyzed under different contact and deformation conditions to estimate material consumption in this complex interlooping layout. Series of laid-in weft-knitted fabrics made of different combinations of ground and inlay yarns were fabricated with the 1 × 1 laid-in loop pattern and tested for the model validation. The comparisons between the experimental and calculated results indicated that the newly developed geometric model favorably agreed with the experimental measurements regarding the ground loop lengths and inlay loop lengths applied in the laid-in weft-knitted structures. The results indicated the applicability of the developed geometric model of laid-in weft-knitted fabrics with similar structural patterns in practical use. The output of this study provides a theoretical and practical reference for structural and physical properties analysis, material consumption prediction, even cost estimation of laid-in weft-knitted fabrics.

Sign in / Sign up

Export Citation Format

Share Document