Synthesis and Photocatalytic Properties of ZnO-Volcanics Composites

2013 ◽  
Vol 331 ◽  
pp. 497-502
Author(s):  
Ai Hua Wang ◽  
Ping Che ◽  
Jie Min Liu ◽  
Gui Hua Wang
Keyword(s):  
Calcination Temperature ◽  
Physical Adsorption ◽  
Sol Gel ◽  
Degradation Efficiency ◽  
X Ray Diffraction ◽  
Photocatalytic Reactor ◽  
Decolorization Rate ◽  
Surface Areas ◽  
Transmission Electron ◽  
Average Grain Size

in this paper, nano-ZnO were synthesized via a sol-gel method, and ZnO-volcanics composites (ZVCs) were prepared via physical adsorption process. The morphology and structure of ZnO/ ZnO-volcanics composites (ZVCs) samples were investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM).BET surface areas of the catalysts were determined by N2 adsorption (BET). According the data of XRD, the average grain size of ZnO is 15.1 nm consistent with the result observed by TEM (16.3 nm). Photocatalytic performance of ZnO and ZVCs were carried out in sprinkling photocatalytic reactor, with methylene blue (MB) as pollutants model. Decolorization rate is select as the evaluation parameters for the degradation effect. The effect of catalyst dosage, MB initial concentration, calcination temperature and pH on the degradation efficiency have been investigated. The MB degradation efficiency was 99.2% when the concentration of MB, the ZVCs, the pH and the calcination temperature were 10 mg/L, 20 g/L, and 10.03, 500 oC respectively. In the catalysts recycle experiments, the decolorization rate of MB using ZVCs is 90.2% after utilization for six times, overwhelmingly higher than that of ZnO (22.6%), indicating immobilization is efficient.

The effect of silver concentration and calcination temperature on structural and optical properties of ZnO:Ag nanoparticles

2015 ◽  
Vol 29 (01) ◽  
pp. 1450254 ◽  
Author(s):  
M. Shayani Rad ◽  
A. Kompany ◽  
A. Khorsand Zak ◽  
M. E. Abrishami
Keyword(s):  
Calcination Temperature ◽  
Sol Gel ◽  
Visible Emission ◽  
X Ray Diffraction ◽  
Ag Nps ◽  
Zno Nps ◽  
Calcination Temperatures ◽  
Transmission Electron ◽  
Xrd Patterns ◽  
Average Size

Pure and silver added zinc oxide nanoparticles ( ZnO -NPs and ZnO : Ag -NPs) were synthesized through a modified sol–gel method. The prepared samples were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence (PL) spectroscopy. In the XRD patterns, silver diffracted peaks were also observed for the samples synthesized at different calcination temperatures of 500°C, 700°C, 900°C except 1100°C, in addition to ZnO . TEM images indicated that the average size of ZnO : Ag -NPs increases with the amount of Ag concentration. The PL spectra of the samples revealed that the increase of Ag concentration results in the increase of the visible emission intensity, whereas by increasing the calcination temperature the intensity of visible emission of the samples decreases.

scholarly journals Photo-acoustic properties of nanoTiO2:Er

2016 ◽  
Vol 5 (4) ◽  
pp. 196
Author(s):  
R. Palomino-Merino ◽  
R. Lozada-Morales ◽  
J. Martínez-Juárez ◽  
G. Juárez-Díaz ◽  
J. Carmona-Rodriguez ◽  
...  
Keyword(s):  
Room Temperature ◽  
Sol Gel ◽  
Acoustic Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Average Grain Size ◽  
Electron Dispersion ◽  
Er Doped ◽  
Spectroscopy Optical

Nanocrystalline Er-doped TiO2 was prepared by sol-gel at room temperature. X-ray diffraction, photoacoustic spectroscopy (optical absorption), transmission electron microscopy (TEM), and electron dispersion microscopy (EDS) were carried out on both as-prepared and thermally-annealed (air at 700 ºC) samples, revealing the anatase crystalline phase of TiO2. The samples exhibit an average grain size from 38 to 5.1 nm, as the nominal concentration of Er varies from 0 % to 7 %. The photoacoustic spectra evidence the absorption edge at 300 nm attributed to TiO2, as well as several electronic transitions which are atomic energy absorption-line levels characteristics of Er.

scholarly journals REMOVAL OF NORFLOXACIN BY TiO2-SBA-15 PHOTOCATALYST

2020 ◽  
Vol 58 (3A) ◽  
pp. 13
Author(s):  
Nguyễn Thị Thu Trang ◽  
Trần Quang Vinh ◽  
Nguyễn Thành Đồng ◽  
Phạm Tuấn Linh ◽  
Nguyễn Viết Hoàng ◽  
...  
Keyword(s):  
Uv Light ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Surface Areas ◽  
Pluronic P123 ◽  
Adsorption Capacities ◽  
Transmission Electron ◽  
Photocatalytic Activities ◽  
Adsorption Desorption ◽  
Synthesized Materials

Ordered SBA-15 mesoporous silica support was synthesized by a sol-gel method using triblock copolymer Pluronic P123 and immobilized with different amounts of photocatalyst TiO2. The synthesized composites were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and N2 adsorption-desorption isotherms. The synthesized materials possessed specific surface areas SBET of 768 m2/g, 544 m2/g, 421 m2/g and 333 m2/g at the TiO2:SiO2 ratio of 0, 0.25, 1.0 and 5.0, respectively. The adsorption capacities and photocatalytic activities under UV light irradiation of these materials were evaluated for Norfloxacin degradation. Experimental results indicate that the highest activity was observed on the sample with TiO2:SiO2 ratio of 1.

Preparation of Zircon Whiskers via Non-Hydrolytic Sol-Gel Process Combined with Molten Salt Method

2014 ◽  
Vol 936 ◽  
pp. 970-974
Author(s):  
Hong Da Wang ◽  
Wei Hui Jiang ◽  
Guo Feng ◽  
Jian Min Liu ◽  
Qian Wu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Molten Salt ◽  
Calcination Temperature ◽  
Raw Materials ◽  
Sol Gel ◽  
Molten Salt Method ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
The One

Zircon whiskers were prepared via non-hydrolytic sol-gel process combined with molten salt method, using Si (OC2H5)4 (TEOS) and ZrCl4 as raw materials, LiF as mineralizer, and Na2WO4 as molten salt. The phase composition, morphology and microstructure of the samples were characterized by X-ray diffraction analysis (XRD), field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The influence of introducing molten salt and calcination temperature on the synthesis and morphology of zircon crystals was investigated. The results show that the introduction of Na2WO4 contributes to the one-dimensional preferential growth of zircon. Zircon whiskers elongated along the c-axis, with diameter of ~100nm and aspect ratio of more than 15, are achieved at the temperature of 850 °C, and neither over low nor over high calcination temperature is conducive to the growth of zircon whiskers.

scholarly journals Preparation and Characterization of Novel Mixed Periodic Mesoporous Organosilica Nanoparticles

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1569
Author(s):  
Hao Li ◽  
Laurence Raehm ◽  
Clarence Charnay ◽  
Jean-Olivier Durand ◽  
Roser Pleixats
Keyword(s):  
Cetyltrimethylammonium Bromide ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Periodic Mesoporous Organosilica ◽  
X Ray ◽  
Surface Areas ◽  
Mesoporous Organosilica ◽  
Transmission Electron ◽  
Cp Mas Nmr

We report herein the preparation of mixed periodic mesoporous organosilica nanoparticles (E-Pn 75/25 and 90/10 PMO NPs) by sol-gel co-condensation of E-1,2-bis(triethoxysilyl)ethylene ((E)-BTSE or E) with previously synthesized disilylated tert-butyl 3,5-dialkoxybenzoates bearing either sulfide (precursor P1) or carbamate (precursor P2) functionalities in the linker. The syntheses were performed with cetyltrimethylammonium bromide (CTAB) as template in the presence of sodium hydroxide in water at 80 °C. The nanomaterials have been characterized by Transmission Electron Microscopy (TEM), nitrogen-sorption measurements (BET), Dynamic Light Scattering (DLS), zeta-potential, Thermogravimetric Analysis (TGA), FTIR, 13C CP MAS NMR and small angle X-ray diffraction (p-XRD). All the nanomaterials were obtained as mesoporous rodlike-shape nanoparticles. Remarkably, E-Pn 90/10 PMO NPs presented high specific surface areas ranging from 700 to 970 m2g−1, comparable or even higher than pure E PMO nanorods. Moreover, XRD analyses showed an organized porosity for E-P1 90/10 PMO NPs typical for a hexagonal 2D symmetry. The other materials showed a worm-like mesoporosity.

Influence of Calcination Temperature towards Fe-TiO2 for Visible-Driven Photocatalyst

2017 ◽  
Vol 888 ◽  
pp. 435-440 ◽  
Author(s):  
Siti Aida Ibrahim ◽  
Muhamad Nazim Ahmid
Keyword(s):  
Visible Light ◽  
Calcination Temperature ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Combined Method ◽  
Calcination Process ◽  
Calcination Temperatures ◽  
Light Region ◽  
Average Grain Size ◽  
Vis Spectroscopy

TiO2 is one of the most promising photocatalysts that is widely used for environmental clean-up due to its ability to degrade organic pollutants in air or water. The purpose of this study is to enhance the photocatalytic activity of TiO2 by absorbing energy in visible light region in order to degrade pollutants. In this study, the nanostructured Fe-TiO2 was successfully synthesised via a combined method of sol-gel and calcination process. The calcination temperatures used varied from 400 to 800 °C. The as-prepared samples were characterized by X-ray diffraction (XRD), FESEM and UV-Vis spectroscopy (UV-Vis). XRD results show that the phases of TiO2 are dependent on calcination temperature. It is found that both TiO2 and Fe-TiO2 phases were transformed from anatase to rutile as the temperatures were increased. FESEM images revealed that the particle size was agglomerated and the average grain size was about 54 to 66 nm. UV-Vis analysis indicated that the incorporation of Fe and varied calcination temperature may affect the optical properties as the absorption profile was shifted from 445 nm to 585 nm. Thus, this results show that Fe-TiO2 is a highly potential photocatalyst to degrade pollutants under visible light irradiation.

Effects of Calcination Temperature on Photoreduction Activity of Cu/TiO2 Nanoparticles

2011 ◽  
Vol 55-57 ◽  
pp. 1648-1652
Author(s):  
Jing Wei ◽  
Xin Tan ◽  
Tao Yu ◽  
Lin Zhao
Keyword(s):  
Calcination Temperature ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Chemical Properties ◽  
Titania Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
One Step ◽  
Doped Titania

A one step sol-gel method was used for preparation of Cu doped titania nanoparticles (NPs). The crystal structures, morphologies and chemical properties were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). We discussed the calcination temperature effection on the photoreduction activity of Cu/TiO2. When the calcination temperature was 500°C, the synthesized Cu/TiO2 performed the highest photocatalytic activity.

scholarly journals The Influence Of NO/O2 On The NOx Storage Properties Over A Pt-Ba-Ce/γ-Al2O3 Catalyst

2019 ◽  
Vol 17 (1) ◽  
pp. 1459-1465
Author(s):  
Xuedong Feng ◽  
Jing Yi ◽  
Peng Luo
Keyword(s):  
Sol Gel ◽  
Chemical Properties ◽  
No Oxidation ◽  
Test Results ◽  
X Ray Diffraction ◽  
Storage Performance ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Physical And Chemical ◽  
Al2o3 Catalyst

AbstractWith the purpose of studying the influence of NO/O2 on the NOx storage activity, a Pt-Ba-Ce/γ-Al2O3 catalyst was synthesized by an acid-aided sol-gel method. The physical and chemical properties of the catalyst were characterized by X-ray diffraction (XRD) and Transmission Electron Microscope (TEM) methods. The results showed that the composition of the catalyst was well-crystallized and the crystalline size of CeO2 (111) was about 5.7 nm. The mechanism of NO and NO2 storage and NOx temperature programmed desorption (NO-TPD) experiments were investigated to evaluate the NOx storage capacity of the catalyst. Pt-Ba-Ce/γ-Al2O3 catalyst presented the supreme NOx storage performance at 350℃, and the maximum value reached to 668.8 μmol / gcat. Compared with O2-free condition, NO oxidation to NO2 by O2 had a beneficial effect on the storage performance of NOx. NO-TPD test results showed that the NOx species stored on the catalyst surface still kept relatively stable even below 350℃.

scholarly journals V2O3/C composite fabricated by carboxylic acid-assisted sol–gel synthesis as anode material for lithium-ion batteries

2021 ◽  
Author(s):  
G. S. Zakharova ◽  
E. Thauer ◽  
A. N. Enyashin ◽  
L. F. Deeg ◽  
Q. Zhu ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Sol Gel ◽  
Carbon Sources ◽  
Lithium Ion ◽  
X Ray Diffraction ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Battery Electrode ◽  
Sol Gel Synthesis

AbstractThe potential battery electrode material V2O3/C has been prepared using a sol–gel thermolysis technique, employing vanadyl hydroxide as precursor and different organic acids as both chelating agents and carbon sources. Composition and morphology of resultant materials were characterized by X-ray diffraction, Raman spectroscopy, scanning and transmission electron microscopies, physical sorption, and elemental analysis. Stability and electronic properties of model composites with chemically and physically integrated carbon were studied by means of quantum-chemical calculations. All fabricated composites are hierarchically structured and consist of carbon-covered microparticles assembled of polyhedral V2O3 nanograins with intrusions of amorphous carbon at the grain boundaries. Such V2O3/C phase separation is thermodynamically favored while formation of vanadium (oxy)carbides or heavily doped V2O3 is highly unlikely. When used as anode for lithium-ion batteries, the nanocomposite V2O3/C fabricated with citric acid exhibits superior electrochemical performance with an excellent cycle stability and a specific charge capacity of 335 mAh g−1 in cycle 95 at 100 mA g−1. We also find that the used carbon source has only minor effects on the materials’ electrochemical performance.

Effect of Calcinations on Characterizations of Fabricated Nano Manganese Ferrite

2013 ◽  
Vol 634-638 ◽  
pp. 2150-2154 ◽  
Author(s):  
Rita Sundari ◽  
Tang Ing Hua ◽  
M. Rusli Yosfiah
Keyword(s):  
Sol Gel ◽  
Volatile Components ◽  
Manganese Ferrite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reflectance Analysis ◽  
Transmission Electron Microscope Analysis ◽  
Electron Microscope Analysis ◽  
Nano Size

A citric acid anionic surfactant has been applied for nano manganese ferrite (MnFeO3) fabrication using sol gel method. The calcinations have been varied for 300, 600 and 800oC. The UVDR (UV-Vis Diffused Reflectance) analysis shows a high absorptive band gap after 400 nm for the 600oC calcinated MnFeO3. The DTA (Differential Thermal Analysis) profiles exhibit remarkably trapped volatile matters (H2O, CO2, and NO2) in the fabricated MnFeO3 under sol gel heat treatment at 100oC and the peaks disappeared as the calcination increased to 600oC. As the temperature elevated from 100 to 300oC, the absorption peaks of volatile components are disappeared as demonstrated clearly by the FTIR (Fourier Transform Infrared) spectra of the fabricated material, which 3393 cm-1 corresponded to OH group, 1624 cm-1 to CO group, and 1384 cm-1 to NO group. The XRD (X-Ray Diffraction) spectra show clearly the alteration process from amorphous to crystalline structure as the calcinations increased from 300 to 600oC. In addition, the TEM (Transmission Electron Microscope) analysis exhibits parts of the fabricated MnFeO3 found in cubic nano size of 15-40 nm under interested calcinations and the result is in agreement with that obtained by XRD investigation.

Sign in / Sign up

Export Citation Format

Share Document