Optimization of Surface Roughness in Dry Turning of Brass

2013 ◽  
Vol 395-396 ◽  
pp. 1035-1039
Author(s):  
On Uma Lasunon
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Arithmetic Mean ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Average Surface Roughness ◽  
Dry Turning ◽  
Carbide Cutting Tool ◽  
Optimal Cutting Condition

This study aimed to investigate the effect of cutting speed, feed and depth of cut on the arithmetic mean surface roughness (Ra). The optimal cutting condition in dry turning brass with carbide cutting tool was also recommended. The experimentation was designed by using Taguchi Method (L9). Three investigated factors with 3-level each were cutting speed (42, 68 and 110 m/min), feed (0.05, 0.1 and 0.15 mm/rev), and depth of cut (0.15, 0.25 and 0.5 mm). The results indicated that speed and feed were significantly affected at average surface roughness. The optimal cutting conditions were cutting speed at 68 m/min, feed at 0.05 mm/rev and depth of cut at 0.15 mm.

Tool Wear and Surface Roughness when Machining AlSi/AlN Metal Matrix Composite Using Uncoated Carbide Cutting Tool

2013 ◽  
Vol 773-774 ◽  
pp. 409-413 ◽  
Author(s):  
M.S. Said ◽  
J.A. Ghani ◽  
Che Hassan Che Haron ◽  
Shahrizan Yusoff ◽  
Mohd Asri Selamat ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Milling Process ◽  
Cutting Condition ◽  
Carbide Cutting Tool

Aluminium silicon alloy (AlSic) matrix composite reinforced with aluminium nitride (AlN) particle is a new generation material for automotive and aerospace application. This material has low density, light weight, high strength, high hardness and stiffness. Metal Matrix Composit (MMC) material is one of the advanced materials which have good future prospects. This paper presents the study of tool wear and surface roughness investigation when milling AlSi/AlN Metal Matrix Composite using uncoated carbide cutting tool. The volume of AlN reinforced particle was 10%. The milling process was carried out under dry cutting condition. The uncoated carbide insert parameters used were cutting speed of (250-750 m/min), while feed rate and depth of cut were kept constant at 0.15 mm/tooth of 0.3mm respectively. The Sometech SV-35 video microscope system and Mitutoyo surface roughness tester were used for tool wear measurements and surface roughness respectively. The results revealed that the tool wear increases with cutting speed (450 m/min). While at high cutting speed, the surface finish improves. It was found that the cutting speed of 750m/min was optimum condition for obtaining smooth finish and longer tool life. Keywords: AlSi/AlN Metal Matrix Composite milling process, tool wear, and surface roughness, uncoated cemented carbide tool

PERFORMANCE OF UNCOATED CARBIDE CUTTING TOOL WHEN MACHINING CAST IRON IN DRY CUTTING CONDITION

2009 ◽  
Vol 23 (06n07) ◽  
pp. 1796-1802 ◽  
Author(s):  
A. G. JAHARAH ◽  
C. H. CHE HASSAN ◽  
M. J. GHAZALI ◽  
A. B. SULONG ◽  
M. Z. OMAR ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cast Iron ◽  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Carbide Cutting Tool ◽  
Cutting Speeds

This paper presents the performance of uncoated carbide cutting tool when machining cast iron in dry cutting conditions. Experiments were conducted at various cutting speeds, feed rates, and depths of cut according to Taguchi method design of experiment using a standard orthogonal array L 9(34). The effects of cutting speeds (100-146 m/min), feed rates (0.20-0.35 mm/tooth) and depths of cut (1.0-2.0 mm) on the tool life, surface roughness and cutting forces were evaluated using ANOVA. Results showed that the effects of cutting speed, depth of cut and the feed rate were similar affecting the failure of the carbide cutting tools within the range of tested machining parameters. The contribution of cutting speed, feed rate, and depth of cut in controlling the tool life were 32.12%, 38.56% and 29.32% respectively. Whereas, the cutting speed was the main factor influencing the average surface roughness (Ra) value followed by feed rate. These factors contribute 60.53% and 35.59% respectively to the Ra value. On the other hand, cutting forces generated were greatly influenced by the depth of cut (66.52%) and the feed rate (32.6%). Cutting speed was found insignificant in controlling the generated cutting forces.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Deep Hole Machining with a Small Diameter Drill and Ultrasonic Vibration

2017 ◽  
Vol 749 ◽  
pp. 107-110
Author(s):  
Yuta Masu ◽  
Tomohito Fukao ◽  
Taiga Yasuki ◽  
Masahiro Hagino ◽  
Takashi Inoue
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Small Diameter ◽  
Maximum Amplitude ◽  
Depth Of Cut ◽  
Deep Hole ◽  
Work Material ◽  
Finished Surface

The method of imparting ultrasonic vibration to the cutting tool is known to improve the shape accuracy and finished surface roughness. However, a uniform evaluation of this function in drilling has not been achieved, and the cutting process cannot be checked from the outside. The aim of this study is to investigate the cutting characteristics in deep hole drilling when an ultrasonic vibrator on the table of a machining center provides vibration with a frequency of 20 kHz to the work piece. The ultrasonic vibrations in this system reach the maximum amplitude in the center of the work material. We evaluated the change in finished surface roughness between the section where drilling starts to the point of maximum amplitude with ultrasonic vibration. The main cutting conditions are as follows: cutting speed (V) 12.6 (mm/min); feed rate (s) 30, 60 (mm/rev); depth of cut (t) = 32 (mm); work material, tool steel; cutting tool material, HSS; point angle (σ) 118 (°); and drill diameter (φ) 4 (mm). Lubricant powder was also added to clarify the cutting effect, and compared the condition in which there was no ultrasonic vibration. The results showed that surface roughness at the point of maximum amplitude was better than that with no vibration.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

scholarly journals Milling Inconel 718 Workpiece With Cryogenically Treated And Untreated Cutting Tools

2021 ◽  
Author(s):  
Hüseyin Gürbüz ◽  
Şehmus Baday
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Abrasive Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Tool Wear ◽  
Feed Force

Abstract Although Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02-0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated.

Life Prediction of Cutting Tool by the Workpiece Cutting Condition

2011 ◽  
Vol 223 ◽  
pp. 554-563 ◽  
Author(s):  
Noemia Gomes de Mattos de Mesquita ◽  
José Eduardo Ferreira de Oliveira ◽  
Arimatea Quaresma Ferraz
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Operating Conditions ◽  
Production Costs ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Workpiece Material ◽  
The Cost

Stops to exchange cutting tool, to set up again the tool in a turning operation with CNC or to measure the workpiece dimensions have direct influence on production. The premature removal of the cutting tool results in high cost of machining, since the parcel relating to the cost of the cutting tool increases. On the other hand the late exchange of cutting tool also increases the cost of production because getting parts out of the preset tolerances may require rework for its use, when it does not cause bigger problems such as breaking of cutting tools or the loss of the part. Therefore, the right time to exchange the tool should be well defined when wanted to minimize production costs. When the flank wear is the limiting tool life, the time predetermination that a cutting tool must be used for the machining occurs within the limits of tolerance can be done without difficulty. This paper aims to show how the life of the cutting tool can be calculated taking into account the cutting parameters (cutting speed, feed and depth of cut), workpiece material, power of the machine, the dimensional tolerance of the part, the finishing surface, the geometry of the cutting tool and operating conditions of the machine tool, once known the parameters of Taylor algebraic structure. These parameters were raised for the ABNT 1038 steel machined with cutting tools of hard metal.

Effects of Cutting Condition on Surface Roughness when Turning Untreated and Sb-Treated Al-11%Si Alloys Using PVD Coated Tools

2013 ◽  
Vol 315 ◽  
pp. 413-417 ◽  
Author(s):  
Mohsen Marani Barzani ◽  
Mohd Yusof Noordin ◽  
Ali Akhavan Farid ◽  
Saaed Farahany ◽  
Ali Davoudinejad
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Manufacturing Processes ◽  
Cutting Condition ◽  
Dry Cutting ◽  
Fabrication Cost ◽  
Coated Tools ◽  
Experimental Trials ◽  
Cutting Speeds

Surface roughness is an important output in different manufacturing processes. Its characteristic affects directly the performance of mechanical components and the fabrication cost. In this current work, an experimental investigation was conducted to determine the effects of various cutting speeds and feed rates on surface roughness in turning the untreated and Sb-treated Al-11%Si alloys. Experimental trials carried out using PVD TIN coated inserts. Experiments accomplished under oblique dry cutting when three different cutting speeds have been used at 70, 130 and 250 m/min with feed rates of 0.05, 0.1 and 0.15 mm/rev, whereas depth of cut kept constant at 0.05 mm. The results showed that Sb-treated Al-11%Si alloys have poor surface roughness in comparison to untreated Al-11%Si alloy. The surface roughness values reduce with cutting speed increment from 70 m/min to 250 m/min. Also, the surface finish deteriorated with increase in feed rate from 0.5 mm/rev to 0.15 mm/rev.

Surface integrity in laser-assisted machining of Ti6Al4V

2020 ◽  
pp. 095440622097825
Author(s):  
O Kalantari ◽  
MM Fallah ◽  
F Jafarian ◽  
SR Hamzeloo
Keyword(s):  
Surface Roughness ◽  
Grain Size ◽  
Surface Integrity ◽  
Cutting Tool ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Laser Source ◽  
Depth Of Cut ◽  
Thermal Source ◽  
Laser Assisted Machining

In laser-assisted machining (LAM), the laser source is focused on the workpiece as a thermal source and locally increases the workpiece temperature and makes the material soft ahead of the cutting tool so using this method, the machining forces are reduced, which causes improving the surface quality and cutting tool life. Machinability of advanced hard materials is significantly low and conventional methods do not work effectively. Therefore, utilizing an advanced method is inevitable. The product life and performance of complex parts of the leading industry depends on surface integrity. In this work, the surface integrity features including microhardness, grain size and surface roughness (Ra) and also the maximum cutting temperature were investigated experimentally in LAM of Ti-6Al-4V. According to the results, cutting speed has inverse effect on the effectiveness of LAM process because with increasing speed (15 to 63 m/min), temperature decreases (524 °C to 359 °C) and surface roughness increases (0.57 to 0.71 μm). Enhancing depth of cut and feed has direct effect on the process temperature, grain size, microhardness and surface roughness.

Machining characteristics of Inconel 718 under several cutting conditions based on Taguchi method

2012 ◽  
Vol 227 (9) ◽  
pp. 1889-1897 ◽  
Author(s):  
R Thirumalai ◽  
JS Senthilkumaar ◽  
P Selvarani ◽  
S Ramesh
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
Flank Wear ◽  
Optimization Technique ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Machining Parameters ◽  
Dry Machining ◽  
Noise Factors

Extensive researchers have conducted several experiments in the past for selecting the optimum parameters in machining nickel based alloy – Inconel 718. These experiments conducted so far are dealt with dry machining and flooded coolant machining of nickel alloy Inconel 718. In this research study, the usage of refrigerated coolant is also dealt with and it is compared with dry machining and flooded coolant machining. Cutting speed, feed and depth of cut are considered as the machining parameters. The effectiveness of the refrigerated coolant in machining the heat resistant super alloy material Inconel 718 with respect to these machining parameters are described in this article. The machinability studies parameters were generated with surface roughness and flank wear. The performance of uncoated carbide cutting tool was investigated at various cutting condition under dry, flooded coolant and refrigerated coolant machining. The relationship between the machining parameters and the performance measures were established and using analysis of variance significant machining parameters determined. This article made an attempt to Taguchi optimization technique to study the machinability performances of Inconel 718. Taguchi approach is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer experiments than a factorial design. Taguchi’s optimization analysis indicates that the factors level, its significance to influence the surface roughness and flank wear for the machining processes. Confirmation tests were conducted at an optimal condition to make a comparison between the experimental results foreseen from the mentioned correlations.

Sign in / Sign up

Export Citation Format

Share Document