Bond Properties of Plain Steel Bar in Concrete with Machine-Made Sand

2013 ◽  
Vol 438-439 ◽  
pp. 20-24
Author(s):  
Feng Lan Li ◽  
Ke Fei Yu ◽  
Xin Xin Ding ◽  
Chang Ming Li
Keyword(s):  
Bond Strength ◽  
Experimental Studies ◽  
Bond Stress ◽  
Test Method ◽  
Bond Properties ◽  
Bond Slip ◽  
Ordinary Concrete ◽  
Strength Grade ◽  
Pull Out ◽  
Steel Bar

To meet the requirement of machine-made sand application in concrete structures, it is necessary to understand the bond properties of steel bar with machine-made sand concrete (MSC). Therefore, the experimental studies were carried out on the bond of plain steel bar with MSC by the central pull-out test method. Three specimens were cast as one group, 6 groups were tested considering the changes of strength grade of MSC and ordinary concrete. The bond-slip curves were measured and analyzed. The results show that the bond slip begins at the tensile side and transfers gradually to the free end before the entire slip turns up along the interface of plain steel bar and surrounded concrete, the largest average bond stress, i. e. the bond strength of plain steel bar corresponds to the initial entire slip of plain steel bar. With the increasing strength grade of MSC and ordinary concrete, the difference of slip at tensile side and free end becomes greater. Comparing that only appears in ordinary concrete with higher strength, the larger slips turn up while the bond stress reaches the largest for the plain steel bar in MSC. Larger scatter of bond strength is between specimens in the same group. Some plain steel bars yields with the beginning of entire slip along the interface.

Bond-Slip Relation of Plain Steel Bar in Concrete with Machine-Made Sand

2012 ◽  
Vol 238 ◽  
pp. 142-146 ◽  
Author(s):  
Shun Bo Zhao ◽  
Xin Xin Ding ◽  
Chang Yong Li
Keyword(s):  
Constitutive Relations ◽  
Concrete Strength ◽  
Experimental Studies ◽  
Test Method ◽  
Group 14 ◽  
Bond Slip ◽  
Pull Out ◽  
Steel Bar ◽  
Characteristic Values ◽  
Powder Content

To meet the requirement of machine-made sand application in concrete structures, experimental studies were carried out on the bond of plain steel bar with Machine-made Sand Concrete (MSC) by the central pull-out test method. Three specimens were cast as one group, 14 groups were tested considering the influence of concrete strength, bond length and stone powder content in machine-made sand. Based on the experimental research, the characteristic values of bond-slip curve such as the initial-slip and ultimate bond stresses with corresponding slips are statistically analyzed, the bond-slip constitutive relations between plain steel bar and MSC were obtained.

scholarly journals Experimental study on the effect of concrete strength and corrosion level on bond between steel bar and concrete

2021 ◽  
Vol 72 (4) ◽  
pp. 498-509
Author(s):  
Vuong Doan Dinh Thien ◽  
Hung Nguyen Thanh ◽  
Hung Nguyen Dinh
Keyword(s):  
Compressive Strength ◽  
Bond Strength ◽  
Concrete Strength ◽  
Concrete Block ◽  
Bond Stress ◽  
Concrete Compressive Strength ◽  
Pull Out ◽  
Steel Bar ◽  
Stress Degradation ◽  
Slip Displacement

Corrosion of the steel reinforcement bars reduces the area of the steel bar and the bond stress between the steel bars and around concrete that decreases the capacity of concrete structures. In this study, the bond stress between steel bar with a diameter of 12mm and concrete was examined with the effect of different corrosion levels and different concrete grades. A steel bar was inserted in a concrete block with a size of 20×20×20cm. The compressive strength of concrete was 25.6MPa, 35.1MPa, and 44.1MPa. These specimens were soaked into solution NaCl 3.5% to accelerate the corrosion process with different corrosion levels in the length of 60mm. The pull-out test was conducted. Results showed that the bond strength of the corroded steel bar was higher than that predicted from CEB-FIP. Slip displacement and the range of slip displacement at the bond strength were reduced when the concrete compressive strength was increased. The rate of bond stress degradation occurred faster with the increment of the corrosion level when the concrete compressive strength was increased.

scholarly journals Bond strength between stell-concrete and between concretes with different ages in structural rehabilitation

2015 ◽  
Vol 8 (5) ◽  
pp. 604-624
Author(s):  
M. R. DORIA ◽  
A. T. C SALES ◽  
N. F. de A. ANDRADE
Keyword(s):  
Bond Strength ◽  
Fresh Concrete ◽  
Tensile Tests ◽  
Bond Stress ◽  
Vertical Shear ◽  
Hardened Concrete ◽  
Pull Out ◽  
Steel Bar ◽  
Different Ages ◽  
Indirect Tensile

ABSTRACTIn inspections of buildings, it is common to find structures that, well before reaching its useful life longer require repairs and reinforcements. This study examined the bond strength between concrete of different ages and between steel and concrete, focusing on the recovery of reinforced concrete structures. To analyze the bond between concrete of different ages, trials with specimens receiving three different types of treatments at the interface between the concrete were performed: brushing; brushing and mortar equal to concrete of substrate and brushing and epoxy layer. Indirect tensile tests and oblique and vertical shear tests at the interface were made . The bond stress between steel and concrete was evaluated by pull out test under the conditions of the bar inserted in the still fresh concrete and when inserted in the hardened concrete with epoxy. Results showed increased bond strength by indirect tensile stress of 15% and 37%; 4% and 12% for the adherence test by oblique shear, and 108% and 178%, for the testing of vertical shear, respectively, for the specimens whose interfaces have received, in addition to brushing, layer of mortar and epoxy bridge, compared to those who received only brushing. Insignificant loss (about 0.52%) of bond stress was noticed for pull out test of steel bar when compared with test results of the specimens that had steel bar inserted in the concrete in the hardened state with epoxy adhesion bridge, with those who had inserted steel bar in fresh concrete.

Numerical Simulation of Bond Properties of Steel Bars in Concrete with Machine-Made Sand

2012 ◽  
Vol 238 ◽  
pp. 176-180
Author(s):  
Shun Bo Zhao ◽  
Xin Xin Ding ◽  
Shi Ming Liu
Keyword(s):  
Concrete Strength ◽  
Experimental Studies ◽  
Theoretical Method ◽  
Finite Element Models ◽  
Bond Properties ◽  
Ansys Software ◽  
Bond Slip ◽  
Bond Behavior ◽  
Steel Bar ◽  
Steel Bars

Based on the experimental studies, finite element models were built using ANSYS software to simulate the bond properties of steel bars in machine-made-sand concrete (MSC), which considered the nonlinear bond behavior of interface between steel bar and MSC. The concrete strength and the bond length of steel bar are considered as the main parameters for calculation. The complete bond-slip curves of plain and deformed steel bars are well simulated comparing those obtained from the experimental studies. The study gives an theoretical method to analyze the bond properties of steel bar in MSC.

scholarly journals STUDY ON BONDING PROPERTY OF POLYURETHANE CEMENT (PUC) TO STEEL BAR

2021 ◽  
Vol 30 (3) ◽  
Author(s):  
Kexin Zhang
Keyword(s):  
Bond Strength ◽  
Protective Layer ◽  
Stress Process ◽  
Anchorage Length ◽  
Bond Slip ◽  
Pull Out ◽  
Steel Bar ◽  
Bonding Property ◽  
Bonding Properties ◽  
Reinforcement Bar

The pull-out test of the bar and PUC is carried out in this paper, the effects of protective layer thickness, reinforcement anchorage length, diameter and shape of reinforcement on bonding properties were studied. The results show that the bond strength between reinforcement and PUC material increases with the increase of the thickness of the protective layer, but decreases with the increase of the anchorage length and diameter of reinforcement. The bond strength of bare round steel is significantly lower than that of ribbed steel, and the maximum bond strength is about 47.4% of ribbed steel. By analyzing the bond slip curve obtained from the pull-out test, the stress process of bond anchorage between reinforcement bar and PUC material is mainly summarized into three stages: the rising stage, the falling stage and the residual stage. The characteristics of the curve, the stress process and the failure mode of specimen at each stage are analyzed.

scholarly journals Bond of Ribbed Steel Bar in High-Performance Steel Fiber Reinforced Expanded-Shale Lightweight Concrete

Buildings ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 582
Author(s):  
Mingshuang Zhao ◽  
Guirong Liu ◽  
Lingli Liu ◽  
Yanyan Zhang ◽  
Kang Shi ◽  
...  
Keyword(s):  
Bond Strength ◽  
High Performance ◽  
Steel Fiber ◽  
Lightweight Concrete ◽  
Volume Fraction ◽  
Bond Stress ◽  
Fiber Reinforced ◽  
Bond Slip ◽  
Steel Bar ◽  
Expanded Shale

For the structural application of high-performance Steel Fiber Reinforced Expanded-shale Lightweight Concrete (SFRELC), a reliable bond of ribbed steel bar should be ensured. In this paper, an experimental study was carried out on the bond properties of ribbed steel bar embedded in SFRELC by the direct pull-out test. The SFRELC was produced with a strength grade of 35 MPa and a volume fraction of steel fiber as 0%, 0.8%, 1.2%, 1.6% and 2.0%, respectively. Fifteen groups of specimens were made with a central placed steel bar with diameter of 14 mm, 20 mm and 28 mm, respectively. Complete bond stress-slip curves were determined for each group of specimens, and the characteristic values of bond-stress and slip at key points of the curves were ascertained. Results show that the bond strength, peak-slip and residual bond strength increased with the increase of the volume fraction of steel fiber. With the increase of steel bar diameter, bond strength decreased while the peak-slip increased, and the descending curves became sharp with a decreased residual bond strength. Formulas for calculating the bond strength and peak-slip were proposed. The relationships were determined for the splitting bond strength, residual bond strength with the bond strength, the splitting bond slip and residual bond slip with the peak-slip. Combined with rational fitting analyses of bond strength and slip, a constitutive model was selected for predicting the bond stress-slip of ribbed steel bar in SFRELC.

scholarly journals Effect of casting direction on bond of reinforcement in High Performance Self-Compacting Concrete (HPSCC)

2019 ◽  
Vol 262 ◽  
pp. 06004 ◽  
Author(s):  
Piotr Dybeł
Keyword(s):  
Bond Strength ◽  
High Performance ◽  
Bond Stress ◽  
Concrete Mixture ◽  
Experimental Program ◽  
Bond Properties ◽  
Self Compacting Concrete ◽  
Pull Out ◽  
Significant Change ◽  
Bond Characteristics

This paper presents the results of an investigation into the steel-to-concrete bond in high-performance self-compacting concrete (HPSCC) based on direct pull-out tests. Specifically, the effect of the casting direction on bond properties is examined. Two variants of concrete mixture casting were considered in this work: from the top and from the bottom of a mould with a single casting point at one edge. Horizontal specimens with transverse rebars distributed over their heights (480 mm) and lengths (1600 mm) were cast. The experimental program has shown that the direction of concreting plays an important role in the formation of the bond condition. In the case of casting a mixture from the bottom of a mould, in the lower part of a specimen there is no significant change of the bond stress. However, there is a strong improvement in the upper part. The phenomenon observed eliminates the top-bar effect. What is more, for the rebars situated in the upper part of a specimen, improvements in bond characteristics, such as the bond stiffness, bond strength and the effect of the rebar distance from the casting point are all observed in the case of casting a mixture from the bottom of a mould.

Bond-Slip Behavior of Steel Bar Embedded in Lightweight Concrete Using Sand Coated Polypropylene Coarse Aggregate

2018 ◽  
Vol 929 ◽  
pp. 103-108 ◽  
Author(s):  
Pamudji Gandjar ◽  
Heribowo Bimasena ◽  
Prayoga Adam Yuta ◽  
Purnomo Heru
Keyword(s):  
Bond Strength ◽  
Coarse Aggregate ◽  
Lightweight Concrete ◽  
Aggregate Gradation ◽  
Bond Slip ◽  
Coarse Aggregates ◽  
Pull Out ◽  
Steel Bar ◽  
Fine Aggregates ◽  
Natural Aggregates

Plastic waste as coarse aggregates in concrete making is part of efforts to reduce environmental pollution. In one hand the use of plastic as aggregates can provide lighter weight of concrete than those using natural aggregates. Accordingly, a comprehensive experimental study on the concrete-steel bond behavior of structural waste polypropylene (PP) lightweight coarse aggregate concrete (WPPLAC) was carried out using different composition, aggregate gradation, type of bar and size diameter of bar. Pull out tests are conducted for three kind of plain and deformed steel bars having diameter 10, 12 and 16 mm respectively, which are embedded in concrete cubes made by the two mixtures to know local bond-slip relation. Two mixtures of sand coated polypropylene (PP) coarse plastic aggregates, sand as fine aggregates, water and Portland Composite Cement with a water-cement ratio of 0.264 are conducted. The first mixture contains 100% of 25 mm sand coated coarse aggregate while the second mixture contains 70% of 25 mm and 30% of 20 mm sand coated coarse aggregates. Bond strength versus steel displacements results in general show that higher bond strength is found for steel bar having larger diameter while steel displacements approximately follow the scale of bar diameter.

scholarly journals Research on bond–slip performance between pultruded glass fiber-reinforced polymer tube and nano-CaCO3 concrete

2020 ◽  
Vol 9 (1) ◽  
pp. 637-649 ◽  
Author(s):  
Zhan Guo ◽  
Qingxia Zhu ◽  
Wenda Wu ◽  
Yu Chen
Keyword(s):  
Bond Strength ◽  
Concrete Strength ◽  
Fiber Reinforced Polymer ◽  
Glass Fiber Reinforced Polymer ◽  
Bond Slip ◽  
Ordinary Concrete ◽  
Bond Performance ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Push Out

AbstractThe article describes an experimental study on the bond–slip performance between the pultruded glass fiber-reinforced polymer (GFRP) tube and the nano-CaCO3 concrete. Taking the nano-CaCO3 concrete strength and GFRP tube thickness as primary parameters, nine specimens were designed and tested to study the influence of these parameters on the bond strength of the specimens. Besides, three specimens filled with the ordinary concrete were also tested by using the push-out tests to make comparisons with the bond performance of the specimens filled with nano-CaCO3 concrete. A total of four push-out tests were conducted on each specimen. The experimental results indicate that there are two types of axial load–slip curves for each specimen in four push-out tests. Moreover, comparison of the results of the push-out tests in the same direction shows that the bond failure load of the specimen decreases with the increase in the number of push-out tests. Based on the analysis of the test results, it is shown that the bond performance between the GFRP tube and the nano-CaCO3 concrete is better than that between the GFRP tube and the ordinary concrete. Furthermore, as the nano-CaCO3 concrete strength increases, the bond strength of the specimens decreases, indicating that the concrete strength has a negative effect on the bond strength. When the nano-CaCO3 concrete strength is relatively smaller (C20), the bond strength of the specimens decreases with the increase in the thickness of the GFRP tube. However, when the nano-CaCO3 concrete strength is relatively larger (C30 and C40), the bond strength of the specimens increases as the thickness of the GFRP tube increases.

Experimental Research on Interfacial Bond Performance in Rock Anchor with High-Performance Grouting Medium

2012 ◽  
Vol 517 ◽  
pp. 932-938 ◽  
Author(s):  
Zhi Fang ◽  
Hong Qiao Zhang
Keyword(s):  
Rock Mass ◽  
Bond Strength ◽  
High Performance ◽  
Interfacial Bond ◽  
Interfacial Bond Strength ◽  
Bond Performance ◽  
Pull Out ◽  
Steel Bar ◽  
Reactive Powder ◽  
Ground Anchor

There exist the problems such as low bond strength and bad durability in the ordinary grouting slurry of the ground anchor system at present. The high-performance grouting mediums RPC (Reactive Powder Concrete) and DSP (Densified Systems containing homogeneously arranged ultrafine Particles) would become the potential replacement of grouting medium in ground anchor resulting from their high compressive strength, durability and toughness. Based on a series of pull-out tests on ground anchors with different high-performance grouting medium of RPC and DSP , different bond length in the construction field, the bond performance on the interfaces between anchor bolt (deformed steel bar) and grouted medium as well as between grouted medium and rock mass was studied. The results indicate that the interfacial bond strength between RPC or DSP and deformed steel bolt ranges within 23-31Mpa, far greater than that (about 2-3MPa) between the ordinary cementitious grout and deformed steel bar. Even though the interfacial bond strength between the grouted medium and rock mass of limestone was not obtained in the test since the failure mode was pull-out of those steel bar rather than the interface shear failure between grouted medium and rock mass, the bond stress on the interface reached 6.2-8.38 MPa, also far greater than the bond strength (about 0.1-3MPa) between the ordinary cementitious slurry and rocks.

Sign in / Sign up

Export Citation Format

Share Document