scholarly journals Using Nanomaterials in Stabilization of Soil for Oil Infrastructures

2020 ◽  
Vol 10 (3) ◽  
pp. 36-53
Author(s):  
Dr. Zaid Hameed Majeed ◽  
Eng. Kadhim Jawad Aubais ◽  
Dr. Mohd Raihan Taha
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Dry Weight ◽  
Environmental Benefits ◽  
Al2o3 Content ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Geotechnical Characteristics ◽  
Compressible Soil

The design foundations  of storage tanks for oil industry experiences significant problems due to the widespread occurrence of weak and compressible soil which resulted in foundation failure. In this study, soft soils were taken from two locations and mixed with three types of nanoparticles which were nano-alumina (nano Al2O3), nano-copper (nano CuO), and nano-magnesium (nano MgO). Nanomaterials were incorporated in small percentage (less than 1%) by dry weight of soil. The tested geotechnical characteristics included the water content, dry density, and the unconfined compressive strength. The results showed significant enhancements in the maximum dry density and unconfined compressive strength. The level of enhancement depended on the type of nanomaterials and the contents. Improved strength and hardening properties were shown with the utilization of nano CuO material in comparison to the soil samples with the other nanomaterials additions, with its optimum addition of 0.7% provided an increment rate of 662.7% while the optimum nano CuO which is about 1% showed a 532% increasing rate in the compressive strength of S1 soil. It was noted that the maximum dry density and unconfined compressive strength enhanced with the increase in the nanoparticles content until reaching a percentage in which the strength decreased. The optimum content of the nano MgO was 0.3% while the optimum nano Al2O3 content was about 0.3% for soil S1 and was about 0.1% for soil S2. The presence of nanomaterials in excessive contents caused agglomeration of particles which had negative influences on mechanical characteristics of the soils. Generally, the incorporation of finer particles like nanoparticles even with low amount would improve the geotechnical characteristics of soils with the consideration of the potential environmental benefits, these combined admixtures are intended to lower the cost and become a more sustainable and environmental alternative for soil stabilization

A Study of Soil Stabilization by Hydrated Lime at Kampung Kedaik Asal, Rompin, Pahang, Malaysia

2014 ◽  
Vol 695 ◽  
pp. 738-741
Author(s):  
Azhani Zukri ◽  
Nadiatul Adilah Ahmad Abdul Ghani
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Optimum Moisture Content ◽  
Natural State ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Lime Content ◽  
Curing Period

This study involves the clay sample which is taken from Kampung Kedaik Asal, Rompin site and evaluation of its properties in natural state and after stabilization. The main objectives of this paper is to estimate the optimum lime content (OLC) needed to stabilize the soil by using Eades-Grim pH Test, to determine the optimum moisture content (OMC) and maximum dry density (MDD) of the treated soil by Standard Proctor Test and also the strength value of the soil specimens with different percentages of lime content corresponding with different curing period by Unconfined Compressive Strength (UCS) Test. From this study, the optimum amount to stabilize the clay soil and minimum amount of lime required to stabilize the soil pH level to 12 is 5%. The results showed that addition of lime decreased the maximum dry density (MDD) and increased the optimum moisture content (OMC). Unconfined compressive test on 48 sets of samples has been carried out for 7, 14 and 28 days of curing with different lime contents such as 5%, 7% and 9%. The highest unconfined compressive strength (UCS) achieved is 321 kN/m2 for clay stabilized with 9% lime content cured at 28 days. From the test results, it was found that the longer the immersion of curing period with higher lime content, the greater the compressive strength of the specimen.

scholarly journals Characterization and Comparison Research on Composite of Alluvial Clayey Soil Modified with Fine Aggregates of Construction Waste and Fly Ash

2021 ◽  
Vol 28 (1) ◽  
pp. 83-95
Author(s):  
Qu Jili ◽  
Wang Junfeng ◽  
Batugin Andrian ◽  
Zhu Hao
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Unconfined Compressive Strength ◽  
Clayey Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Construction Waste ◽  
Comparison Research ◽  
Fine Aggregates ◽  
Optimum Water Content

Abstract Fine aggregates of construction waste and fly ash were selected as additives to modify the characteristics of Shanghai clayey soil as a composite. The laboratory tests on consistency index, maximum dry density, and unconfined compressive strength were carried out mainly for the purpose of comparing the modifying effect on the composite from fine aggregates of construction waste with that from fly ash. It is mainly concluded from test results that the liquid and plastic limit of the composites increase with the content of two additives. But their maximum dry density all decreases with the additive content. However, fine aggregates of construction waste can increase the optimum water content of the composites, while fly ash on the contrary. Finally, although the two additive all can increase the unconfined compressive strength of composites, fly ash has better effect. The current conclusions are also compared with previous studies, which indicates that the current research results are not completely the same as those from other researchers.

Correlation of Unconfined Compressive Strength and California Bearing Ratio in Laterite Soil Stabilization Using Varied Zeolite Content Activated by Waterglass

2020 ◽  
Vol 998 ◽  
pp. 323-328
Author(s):  
Achmad Bakri Muhiddin ◽  
Marthen M. Tangkeallo
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Dry Weight ◽  
Engineering Properties ◽  
High Plasticity ◽  
Curing Time ◽  
Laterite Soil ◽  
Zeolite Content ◽  
Meta Silicate

In remote areas, most roads still use pavements that are very sensitive to climate change, especially those using clay pavements with high plasticity. In addition to the issue of cost, the difficulty of obtaining a proper source of material is another problem that has led to soaring prices for materials. In this regard, a study was conducted using local materials, namely zeolite as a stabilizing material added with waterglass as activating agent. The research began with samples of laterite soil and natural zeolite for XRD test (microstructure testing), and then testing for laterite soil’s index properties and engineering properties, namely Unconfined Compressive Strength and CBR value. The purpose of the test is to determine the correlation between the Unconfined Compressive Strength (UCS) and the soil bearing capacity (CBR) caused by adding zeolite as stabilizer material and waterglass as activator with increasing curing time. Laterite soils contain a brownish red iron oxide. The stabilizing material zeolite contains a crystalline mineral of alumina silicate SiO2. While waterglass composed of sodium meta silicate. Stabilization carried out by mixing 4%, 8%, 12%, 16%, and 20% of zeolite with addition of 2% waterglass, percentage was measured based on soil dry weight. Specimens were tested at curing time of 0, 7, 14, and 28 days. The test result shows increasing UCS and CBR values with increasing percentage of zeolite. At mix of 20% zeolite and 2% waterglass, the unconfined compressive strength reaches 23.54 kg/cm2 with CBR value 58% at 28 days of curing time.

scholarly journals Compaction and Plasticity Comparative Behaviour of Soft Clay Treated with Coarse and Fine Sizes of Ceramic Tiles

2018 ◽  
Vol 34 ◽  
pp. 01012 ◽  
Author(s):  
Mohammed Ali Mohammed Al-Bared ◽  
Aminaton Marto ◽  
Indra Sati Hamonangan Harahap ◽  
Fauziah Kasim
Keyword(s):  
Soil Stabilization ◽  
Soft Soil ◽  
Soft Clay ◽  
Cost Effective ◽  
Dry Weight ◽  
Dry Density ◽  
Ceramic Tiles ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stiff Soil

Recycled blended ceramic tiles (RBT) is a waste material produced from ceramic tile factories and construction activities. RBT is found to be cost effective, sustainable, environmental-friendly and has the potential to be used as an additive in soft soil stabilization. Recent reports show that massive amounts of RBT are dumped into legal or illegal landfills every year consuming very large spaces and creating major environmental problems. On the other hand, dredged marine clay obtained from Nusajaya, Johor, Malaysia has weak physical and engineering characteristics to be considered as unsuitable soft soil that is usually excavated, dumped into landfills and replaced by stiff soil. Hence, this study investigates the suitability of possible uses of RBT to treat marine clay. Laboratory tests included Standard proctor tests and Atterberg limits tests. The plasticity of marine clay was evaluated by adding 10%, 20%, 30% and 40% of 0.3 mm RBT. In addition, the compaction behaviour of treated marine clay was compared by adding two different sizes (0.3 mm and 1.18 mm diameter) of RBT. For both coarse and fine sizes of RBT, 10%, 20%, 30% and 40% of the dry weight of the soft clay were added. The mixture of each combination was examined in order to evaluate the Maximum Dry Density (MDD) and the optimum moisture content (OMC) for the treated soft clay. MDD and OMC for soft untreated samples were 1.59 Mg/m3 and 22%, respectively. Treated samples with 10%, 20%, 30% and 40% of 0.30 mm size RBT resulted in a significant reduction of OMC ranged from 19 to 15% while MDD resulted in increment ranged from 1.69 to 1.77 Mg/m3. In addition, samples treated with 10%, 20%, 30% and 40% of 1.18 mm size RBT resulted in major reduction of OMC ranged from 15 to 13.5% while MDD increased effectively from 1.75 to 1.82 Mg/m3. For all mix designs of soft clay-RBT, MDD was gradually increasing and OMC was sharply reducing with further increments of both sizes of RBT.

scholarly journals Engineering behaviour of stabilized laterite and kaolin using lignin

2018 ◽  
Vol 250 ◽  
pp. 01008
Author(s):  
Tuan Noor Hasanah Tuan Ismail ◽  
Siti Aimi Nadia Mohd Yusoff ◽  
Ismail Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
...  
Keyword(s):  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Laboratory Tests ◽  
Dry Weight ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Laterite Soil ◽  
Maximum Dry Density ◽  
Steady Rate

Soils at many sites do not always have enough strength to bear the structures constructed over them and some of the soil may need to be stabilized in order to improve their geotechnical properties. In this paper, routine laboratory tests were critically carried out to investigate the efficacy of lignin in improving the strength behaviour of the soils. Two different soil samples (laterite and kaolin) were studied and mixed with different proportions of lignin (2% and 5% of dry weight of soil), respectively. Unconfined Compressive Strength (UCS) characteristics evaluated in this study were done on samples at their maximum dry density and optimum moisture content (obtained from compaction tests). The UCS tests on all the specimens were carried out after 0, 7, 15, 21 and 30 days of controlled curing. The research results showed that the addition of lignin into kaolin reduced its maximum dry density while giving progressively higher optimum moisture content. Contrarily, with the laterite soil, both maximum dry density and optimum moisture content simultaneously increased when lignin was added into the soils. The UCS results showed that the the stabilized laterite with 2% lignin continued to gain strength significantly at a fairly steady rate after 7 days. Unfortunately, lignin did not show a significant effect in kaolin.

scholarly journals Influence of Lime for Enhancing Characteristics of Expansive Soils in Road Works

2021 ◽  
Vol 1197 (1) ◽  
pp. 012077
Author(s):  
K.S Chamberlin ◽  
M. Rama Rao
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Expansive Soils ◽  
Black Cotton Soil ◽  
Dry Density ◽  
Test Results ◽  
Lime Treatment ◽  
Maximum Dry Density ◽  
Slaked Lime ◽  
Black Cotton Soils

Abstract Expansive soils are found in black cotton soils, which swell or shrink in volume when presented to changes in moisture content. Lime treatment is exhaustively used to increment the properties of sensitive and fragile soils. One of the hugest clarifications behind using lime is to decline the developing presentation of the earth soil. The arrangement of extra safeguards improves the reaction of quicklime (CaO) with water, structures hydrated (slaked) lime (Ca (OH)2), and thus earth characteristics. The vast inadequacy of employing lime is growing the deficiency of lime offset earth. Following that, the goal of this study is to see how re-establishing time affects the geotechnical qualities of settled Black cotton soils with lime. These discoveries recommend that adding Lime as a stabilizer works on the strength of black cotton soil. Some of the characteristics of the soil likely to be increased by using stabilizer in this work are UCS (Unconfined Compressive Strength) at different curing periods (7,14,28 and 56 days), CBR (California Bearing Ratio) value at unsoaked and soaked and MDD (Maximum Dry Density) decrease at different lime percentages(%) like 2.4.6.8 and 10. The result showed here untreated soil got stabilized by using the stabilizer in certain extent In this adjustment various rates of cementitious material is added to black cotton soil and directed tests like plasticity, compaction, swell pressure, free swell index(FSI), Coefficient of permeability (k) and CBR(soaked and unsoaked) at various conditions like OMC,OMC+2% water and OMC+5% water, UCS (Unconfined Compressive Strength) was performed. From the test results, it is identified that the stabilization agent decreases plasticity and improves strength characteristics. Addition of stabilizing agent makes the black cotton soil to non-plastic, non-swelling and attains increase CBR values which are greater than 25% for a dosage of 10% lime at OMC but remaining OMC+2%water & OMC+5%water CBR values are not various much difference as per test results. With the addition of lime, the black cotton soil becomes non-plastic, non-swelling, and has high strengths. Treated soils are used as a development material, for example, a subgrade layer in the development of adaptable asphalt pavements for roads.

scholarly journals Strength Improvement of Weak Subgrade Soil Using Cement and Lime

2019 ◽  
Vol 4 (1) ◽  
Author(s):  
Anigilaje B Salahudeen ◽  
Ja’afar A Sadeeq
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Optimum Moisture Content ◽  
Atterberg Limits ◽  
California Bearing Ratio ◽  
Natural Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Subgrade Soil

The study investigate the suitability of subgrade soil in Baure Local Government Area of Kastina State Nigeria for road construction. The strength properties of the  subgrade was improved using lime and cement. Several analysis including the particle size distribution, specific gravity, Atterberg limits, compaction characteristics, unconfined compressive strength and California bearing ratio tests were performed on natural and lime/cement treated soil samples in accordance with BS 1377 (1990) and BS 1924 (1990) respectively. Soil specimens were prepared by mixing the soil with lime and cement in steps of 0, 3, 6, and 9% by weight of dry soil in several percentage combinations. The Atterberg limits of the weak subgrade soils improved having a minimum plasticity index value of 5.70 % at 3%Lime/6%Cement contents. The maximum dry density (MDD) values obtained showed a significant improvement having a peak value of 1.66 kN/m3 at 9%Lime/9%Cement contents. Similarly, a minimum value of 18.50 % was observed for optimum moisture content at 9%Lime/9%Cement contents which is a desirable reduction from a value of 25.00 % for the natural soil. The unconfined compressive test value increased from 167.30 kN/m2 for the natural soil to 446.77 kN/m2 at 9%Lime/9%Cement contents 28 days curing period. Likewise, the soaked California bearing ratio values increased from 2.90 % for the natural soil to 83.90 % at 9%Lime/9%Cement contents. Generally, there were improvements in the engineering properties of the weak subgrade soil when treated with lime and cement. However, the peak UCS value of 446.77 kN/m2 fails to meet the recommended UCS value of 1710 KN/m2 specified by TRRL (1977) as a criterion for adequate stabilization using Ordinary Portland Cement.            Keywords: Weak subgrade soil, Lime, Cement, Atterberg limits, Maximum dry density, Optimum moisture content, Unconfined compressive strength, California bearing ratio

Behavior of Cohesive Soil Reinforced by Polypropylene Fiber

2020 ◽  
Vol 38 (6A) ◽  
pp. 801-812
Author(s):  
Mohammed A. Al-Neami ◽  
Falah H. Rahil ◽  
Yaseen H. Al-Ani
Keyword(s):  
Soil Stabilization ◽  
Critical Role ◽  
Polypropylene Fiber ◽  
Dry Weight ◽  
Cohesive Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Entire Structure ◽  
Optimum Water Content ◽  
Optimum Water

For any land-based structure, the foundation is very important and has to be strong to support the entire structure. In order for the foundation to be strong, the soil underneath it plays a very critical role. Some projects where the soil compacted by modifying energy is insufficient to achieve the required results, so the additives as a kind of installation and reinforcement are used to achieve the required improvement. This study introduces an attempt to improve cohesive soil by using Polypropylene Fiber instead of conventional kinds used in soil stabilization. Three different percentages (0.25%, 0.5%, and 0.75% by dry weight of soil) and lengths (6, 12, and 18) mm of fiber are mixed with cohesive as a trial to enhance some properties of clay. The results of soil samples prepared at a dry density at three different water conditions (optimum water content, dry side, and wet side) showed that the increase of the percentage and length of polypropylene fiber causes a reduction in the maximum dry density of soils. Soil cohesion increases with the increase of PPF up to 0.5% then decreased. The length of Polypropylene fiber has a great effect on the cohesion of soil and adding 0.5% Polypropylene fibers with a length of 18mm to the soils consider the optimum mix for design purposes to improve the soil. Finally, the soil reinforced by PPF exhibits a reduction in the values of the compression ratio (CR) and accelerates the consolidation of the soil.

scholarly journals Geotechnical Properties of Effluent-Contaminated Cohesive Soils and Their Stabilization Using Industrial By-Products

Processes ◽  
2018 ◽  
Vol 6 (10) ◽  
pp. 203 ◽  
Author(s):  
Muhammad Irfan ◽  
Yulong Chen ◽  
Muhammad Ali ◽  
Muhammad Abrar ◽  
Ahmed Qadri ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Industrial Effluents ◽  
Liquid Limit ◽  
Dry Density ◽  
Cohesive Soils ◽  
Maximum Dry Density ◽  
Plastic Clay ◽  
Swell Potential ◽  
By Products

The unchecked and unnoticed disposal of industrial leachates is a common malpractice in developing countries. Untreated effluents from industries drastically deteriorate the soil, altering nearly all of its characteristics. An increase in urbanization has led to construction on these deteriorated lands. In this study, the chemical impact of two industrial effluents, dyeing (acidic) and tannery (basic), is studied on two cohesive soils, i.e., high plastic clay (CH) and low plastic clay (CL). Properties such as liquid limit, plasticity index, specific gravity, maximum dry density, unconfined compressive strength, swell potential, swell pressure, and compression indices decrease with effluent contamination, with the exception of the basic effluent, for which the trend changes after a certain percentage. This study also examines the time variation of properties at different effluent percentages, finding that unconfined compressive strength of both soils increases with time upon dyeing (acidic) contamination and decreases with tannery (basic). The stabilizing effect of two industrial by-products, i.e., marble dust and ground granulated blast furnace slag (GGBFS) have been evaluated. Unlike their proven positive effect on uncontaminated soils, these industrial by-products did not show any significant stabilization effect on leachate-contaminated cohesive soils, thereby emphasizing the need to utilize special remediation measures for effluent treated soils.

scholarly journals Experimental Study on Unconfined Compressive Strength of Basalt Fiber Reinforced Clay Soil

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Lei Gao ◽  
Guohui Hu ◽  
Nan Xu ◽  
Junyi Fu ◽  
Chao Xiang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Clay Soil ◽  
Soil Column ◽  
Basalt Fiber ◽  
Dry Density ◽  
Fiber Reinforced ◽  
Maximum Dry Density ◽  
Sem Images ◽  
Reinforced Clay

In order to study the mechanism and effect of basalt fiber reinforced clay soil, a series of unconfined compressive strength tests conducted on clay soil reinforced with basalt fiber have been performed under the condition of optimum water content and maximum dry density. Both the content and length of basalt fiber are considered in this paper. When the effect of content is studied, the 12 mm long fibers are dispersed into clay soil at different contents of 0.05%, 0.1%, 0.15%, 0.20%, 0.25%, 0.30%, and 0.35%. When the effect of length is researched, different lengths of basalt fibers with 4 mm, 8 mm, 12 mm, and 15 mm are put into soil at the same content of 0.05%. Experimental results show that basalt fiber can effectively improve the UCS of clay soil. And the best content and length are 0.25% and 12 mm, respectively. The results also show that the basalt fiber reinforced clay soil has the “poststrong” characteristic. About the reinforcement mechanism, the fiber and soil column-net model is proposed in this paper. Based on this model and SEM images, the effect of fiber content and length is related to the change of fiber-soil column and formation of effective fiber-soil net.

Sign in / Sign up

Export Citation Format

Share Document