Synthesis and Characterization of Hollow Anatase TiO2 Spheres and its Application in the Photodegradation of γ-Lindane under Ultraviolet Light

2014 ◽  
Vol 699 ◽  
pp. 245-250
Author(s):  
Afrouz Baharvand ◽  
Alias Mohd Yusof ◽  
Rusmidah Ali ◽  
Mohd Marsin Sanagi ◽  
Sheela Chandren ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Uv Light ◽  
Sol Gel ◽  
Hydrothermal Process ◽  
Hollow Spheres ◽  
Bet Surface Area ◽  
Tetrabutyl Titanate ◽  
Anatase Titania ◽  
Scanning Electron

Hollow anatase titania spheres have been synthesized using hydrothermally–prepared carbon spheres as the template. Here, the combination of hydrothermal process with sol–gel followed by calcination in air was done in order to obtain hollow anatase TiO2 spheres by utilizing fructose and tetrabutyl titanate (TBT) as the precursors. The structure and morphology of the products were characterized using various techniques, including Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), thermal gravimetric and differential thermal analysis (TG–DTA), scanning electron microscopy (SEM), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). XRD showed that all peaks of TiO2 correspond to anatase crystalline phase. The BET surface area of the hollow spheres was about 22 m2g-1. The photocatalytic activity of the hollow anatase TiO2 was measured under UV light using γ-lindane as the target pollutant and was compared to commercially available TiO2.

Synthesis、Structure and Catalytic Activity of TiO2/ La2Zr2O7 Nanocomposites

2011 ◽  
Vol 239-242 ◽  
pp. 2878-2881
Author(s):  
Yu Ping Tong ◽  
Yu Qing Zhao ◽  
Hong Yuan Huo ◽  
Hui Yang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Sol Gel ◽  
Photocatalytic Property ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
X Ray ◽  
Scanning Electron

TiO2/La2Zr2O7 composites were fabricated by sol-gel method. The composites were characterized by X-ray powder diffraction (XRD), Raman spectrum, scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS) and Brunauer-Emmett-Teller (BET) nitrogen adsorption. The results showed that TiO2 was uniformly coated on the surface of La2Zr2O7 powders. The BET surface area of TiO2/La2Zr2O7 composites was 26.78 m2/g, which was larger than that of La2Zr2O7. Also, the photodegradation of methyl orange was used to evaluate its photocatalytic property. It was found that TiO2/La2Zr2O7 composites showed good photocatalytic activity and the decomposition of methyl orange had basically completed within 30 min.

The Facile Hydrothermal Preparation of WO3 and its Photocatalytic Performance under Visible-Light Irradiation

2014 ◽  
Vol 936 ◽  
pp. 347-351 ◽  
Author(s):  
Fen Fen Li ◽  
Hong Tao Gao ◽  
Guang Jun Liu
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photocatalytic Performance ◽  
Uv Light ◽  
Hydrothermal Process ◽  
Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
Hydrothermal Preparation ◽  
X Ray ◽  
Scanning Electron

The orthorhombic WO3 nanoplates were fabricated via a hydrothermal process, using HBF4 as the acid source. They were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-vis diffused reflectance spectroscopy (UV-Vis DRS), respectively. The WO3 nanoplates exhibited nice UV-light driven photocatalytic performance in the degradation of Rhodamine B (RhB).

scholarly journals Structural and optical properties of SnO2–Al2O3 nanocomposite synthesized via sol-gel route

2015 ◽  
Vol 33 (4) ◽  
pp. 714-718 ◽  
Author(s):  
Neeraj K. Mishra ◽  
Chaitnaya Kumar ◽  
Amit Kumar ◽  
Manish Kumar ◽  
Pratibha Chaudhary ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Optical Properties ◽  
Sol Gel ◽  
Physical Interaction ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
X Ray ◽  
Sensing Applications ◽  
Scanning Electron

AbstractA nanocomposite of 0.5SnO2–0.5Al2O3 has been synthesized using a sol-gel route. Structural and optical properties of the nanocomposite have been discussed in detail. Powder X-ray diffraction and scanning electron microscopy with energy-dispersive X-ray diffraction spectroscopy confirm the phase purity and the particle size of the 0.5SnO2–0.5Al2O3 nanocomposite (13 to 15 nm). The scanning electron microscopy also confirms the porosity in the sample, useful in sensing applications. The FT-IR analysis confirms the presence of physical interaction between SnO2 and Al2O3 due to the slight shifting and broadening of characteristic bands. The UV-Vis analysis confirms the semiconducting nature because of direct transition of electrons into the 0.5SnO2–0.5Al2O3 nanocomposites.

Grain growth and sintering in Bi–(Pb)—Sr—Ca—Cu—O superconductors made by sol-gel

1994 ◽  
Vol 9 (2) ◽  
pp. 286-291 ◽  
Author(s):  
Kunsong Ma ◽  
Alain C. Pierre
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Citric Acid ◽  
Grain Growth ◽  
Sol Gel ◽  
Gel Processing ◽  
Scanning Electron

Bi—(Pb)—Sr—Ca—Cu—O superconductors were synthesized by sol-gel processing from nitrates by complexation with citric acid. Their grain growth and sintering above 800 °C were studied by Scanning Electron Microscopy (SEM) and Brunauer, Emmett, Teller (BET) porosimetry. The sintering was limited by anisotropic grain growth, and microcracks in 2212 phase grains were created due to the formation of 2223 phase.

Preparation of Borosilicate Xerogel and Research on its Mineralization

2012 ◽  
Vol 476-478 ◽  
pp. 2059-2062
Author(s):  
Chen Wang ◽  
Ya Dong Li ◽  
Gu Qiao Ding
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Ph Value ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Compositional Changes ◽  
Scanning Electron

Tributyl borate was first adopted for the introduction of boron in the preparation of bioactive borosilicate xerogel by sol-gel method. The xerogel reacted continuously in 0.25M K2HPO4 solution with a starting pH value of 7.0 at 37 °C for 1day. The structural, morphologies and compositional changes resulting from the conversion were characterized using X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. The results indicated that speed of formation of HA was cut way back on the time with the addition of boron and the induction period for the HA nucleation on the surface of the borosilicate xerogel was short than 1 days. The conversion mechanism of the borosilicate xerogels to hydroxyapaptite was also discussed.

scholarly journals KARAKTERISASI KAPASITOR BARIUM STRONTIUM TITANAT (BST) Ba0,75 Sr0,25 TiO3 , YANG DIBUAT MENGGUNAKAN METODE SOL-GEL

2019 ◽  
Vol 16 (1) ◽  
pp. 65
Author(s):  
Rahmi Dewi ◽  
Tiara Pertiwi ◽  
Krisman Krisman
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Impedance Spectroscopy ◽  
Strontium Titanate ◽  
Barium Strontium Titanate ◽  
Sol Gel ◽  
Barium Strontium ◽  
Scanning Electron

The thin film of Barium Strontium Titanate (BST) has been studied withcomposition ofby using sol-gel method that annealed in temperature of 600oC and 650oC. The thin film of BST is characterized by using Field Emission Scanning Electron Microscopy (FESEM) and an impedance spectroscopy. The results of  FESEM characterization for samples in temperature of 600oC and 650oC are 55.83 nm and 84.88 nm in thickness respectively. The result of impedance spectroscopy characterization given frequency values obtained by the impedance value of real and imaginary.The capacitance value at a frequency of 20 Hz from a thin film of BST in temperature of 600oC and 650oC are 69.36Fand138.70F. The dielectric constant of the thin film of BST in temperature of 600oC and 650oC are 22.17 dan 131.56 respectively.

scholarly journals Synthesis of Brushite from Phophogypsum Industrial Waste

2021 ◽  
Vol 12 (5) ◽  
pp. 6580-6588
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Industrial Waste ◽  
Sol Gel ◽  
Dicalcium Phosphate Dihydrate ◽  
X Ray Diffraction ◽  
Characterization Methods ◽  
X Ray ◽  
Phosphate Dihydrate ◽  
Scanning Electron

Dicalcium phosphate dihydrate (DCPD) nanoparticles, also known as brushite, are considered an important bioceramic compound. In this study, brushite was prepared from Moroccan phosphogypsum (PG) using a new sol-gel method. A two-step technique undergoes the synthesis of brushite, the preparation of anhydrite from PG followed by adding phosphoric acid in the presence of sodium hydroxide. The morphology, the chemical composition, and the crystallites size were obtained using Scanning Electron Microscopy (SEM-EDAX), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR), respectively. According to the Debye-Scherrer equation, these characterization methods indicated that the synthesized brushite was highly pure according to the Ca/P ratio of 1.14 and an average crystallites size estimated at 66 nm. These results proved that the brushite was successfully synthesized from Moroccan phosphogypsum.

scholarly journals Surface Properties of Silica–MWCNTs/PDMS Composite Coatings Deposited on Plasma Activated Glass Supports

2021 ◽  
Vol 11 (19) ◽  
pp. 9256
Author(s):  
Michał Chodkowski ◽  
Iryna Ya. Sulym ◽  
Konrad Terpiłowski ◽  
Dariusz Sternik
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Scanning Electron Microscopy ◽  
Multiwalled Carbon Nanotubes ◽  
Composite Coatings ◽  
Thermal Analyses ◽  
Sol Gel ◽  
Visible Range ◽  
Multiwalled Carbon ◽  
Scanning Electron

In this paper, we focus on fabrication and physicochemical properties investigations of silica–multiwalled carbon nanotubes/poly(dimethylsiloxane) composite coatings deposited on the glass supports activated by cold plasma. Air or argon was used as the carrier gas in the plasma process. Multiwalled carbon nanotubes were modified with poly(dimethylsiloxane) in order to impart their hydrophobicity. The silica–multiwalled carbon nanotubes/poly(dimethylsiloxane) nanocomposite was synthesized using the sol–gel technique with acid-assisted tetraethyl orthosilicate hydrolysis. The stability and the zeta potential of the obtained suspension were evaluated. Then, the product was dried and used as a filler in another sol–gel process, which led to the coating application via the dip-coating method. The substrates were exposed to the hexamethyldisilazane vapors in order to improve their hydrophobicity. The obtained surfaces were characterized by the wettability measurements and surface free energy determination as well as optical profilometry, scanning electron microscopy, and transmittance measurements. In addition, the thermal analyses of the carbon nanotubes as well as coatings were made. It was found that rough and hydrophobic coatings were obtained with a high transmittance in the visible range. They are characterized by the water contact angle larger than 90 degrees and the transmission at the level of 95%. The X-ray diffraction studies as well as scanning electron microscopy images confirmed the chemical and structural compositions of the coatings. They are thermally stable at the temperature up to 250 °C. Moreover, the thermal analysis showed that the obtained composite material has greater thermal resistance than the pure nanotubes.

Synthesis and Film Investigation of Titania

2013 ◽  
Vol 832 ◽  
pp. 128-131
Author(s):  
Sharipah Nadzirah ◽  
Uda Hashim
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
Scanning Electron Microscopy ◽  
Titanium Dioxide ◽  
Sol Gel ◽  
Titanium Butoxide ◽  
Before And After ◽  
Scanning Electron ◽  
Spin Coater

Titania or titanium dioxide (TiO2) thin film has been synthesized via sol-gel method with monoethanolamine (MEA) as a catalyst. The mixing of titanium butoxide as a precursor, ethanol as a solvent and MEA were stirred using magnetic stirrer under ambient temperature [. The TiO2solution prepared then was deposited on SiO2substrates using spin-coater and the coated films were annealed at 600°C. Finally, both before and after annealed TiO2thin films were characterized using Field Emission Scanning Electron Microscopy (FESEM). The obtained results show the different TiO2particles formation before and after annealed.

Synthesis of PZT Disks by a Hydrothermal Method

2012 ◽  
Vol 174-177 ◽  
pp. 592-595
Author(s):  
Lin Lin Yang ◽  
Yong Gang Wang ◽  
Yu Jiang Wang ◽  
Xiao Feng Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Hydrothermal Method ◽  
Formation Mechanism ◽  
Powder Diffraction ◽  
Self Assembly ◽  
Hydrothermal Process ◽  
X Ray ◽  
Extended Length ◽  
Scanning Electron

The organization of nanostructures across extended length scales is a key challenge in the design of integrated materials with advanced functions. PbZr0.52Ti0.48O3multilayer disks which were constructed by oriented rectangle nanoparticles were easily prepared by a simple surfactant-free hydrothermal process. The as-prepared powders were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM). The results indicated that the as-prepared PZT disks were constructed by self-assembly of rectangle nanoparticles by a perfect manner. The formation mechanism of the products was discussed.

Sign in / Sign up

Export Citation Format

Share Document