Components of Fracture Response of Steel Fibre Reinforced Concrete Specimens

2016 ◽  
Vol 827 ◽  
pp. 287-291 ◽  
Author(s):  
Ivana Havlíková ◽  
Petr Frantík ◽  
Pavel Schmid ◽  
Hana Šimonová ◽  
Václav Veselý ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
Plain Concrete ◽  
Fibre Reinforced Concrete ◽  
Steel Fibre Reinforced Concrete ◽  
Three Point Bending ◽  
Notched Specimens ◽  
Fracture Tests ◽  
Work Of Fracture

Records of fracture tests on steel fibre reinforced concrete notched specimens in a three-point bending configuration are evaluated in detail and selected results are discussed in the paper. The values of fracture parameters are determined using work of fracture method and double-K fracture model. Primarily, the role of plain concrete as a matrix in steel fibre reinforced concrete specimens is studied with regard to the recorded fracture response.

Experimental Tests of Steel Fibre Reinforced Concrete Beams under Drop-Weight Impacts

2014 ◽  
Vol 626 ◽  
pp. 311-316 ◽  
Author(s):  
Yi Fei Hao ◽  
Hong Hao ◽  
Gang Chen
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Fibre Reinforced Concrete ◽  
Steel Fibres ◽  
Steel Fibre Reinforced Concrete ◽  
Impact Tests ◽  
Drop Weight ◽  
The Impact

Concrete is a brittle material, especially under tension. Intensive researches have been reported to add various types of fibres into concrete mix to increase its ductility. Recently, the authors proposed a new type of steel fibre with spiral shape to reinforce concrete material. Laboratory tests on concrete cylinder specimens demonstrated that compared to other fibre types such as the hooked-end, deformed and corrugated fibres the new fibres have larger displacement capacity and provide better bonding with the concrete. This study performs drop-weight impact tests to investigate the behaviour of concrete beams reinforced by different types of steel fibres. The quasi-static compressive and split tensile tests were also conducted to obtain the static properties of plain concrete and steel fibre reinforced concrete (FRC) materials. The quasi-static tests were carried out using hydraulic testing machine and the impact tests were conducted using an instrumented drop-weight testing system. Plain concrete and concrete reinforced by the commonly used hooked-end steel fibres and the proposed spiral-shaped steel fibres were tested in this study. The volume dosage of 1% fibre was used to prepare all FRC specimens. Repeated drop-weight impacts were applied to the beam specimens until total collapse. A 15.2 kg hard steel was used as the drop-weight impactor. A drop height of 0.5 m was considered in performing the impact tests. The force-displacement relations and the energy absorption capabilities of plain concrete and FRC beams were obtained, compared and discussed. The advantage and effectiveness of the newly proposed spiral-shaped steel fibres in increasing the performance of FRC beam elements under impact loads were examined.

Experimental study of the tensile and flexural mechanical properties of directionally distributed steel fibre-reinforced concrete

2018 ◽  
Vol 233 (9) ◽  
pp. 1721-1732 ◽  
Author(s):  
Fangyuan Li ◽  
Yunxuan Cui ◽  
Chengyuan Cao ◽  
Peifeng Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Steel Fibre ◽  
Plain Concrete ◽  
Design Parameters ◽  
Fibre Reinforced Concrete ◽  
Split Tensile Strength ◽  
Fibre Direction ◽  
Steel Fibre Reinforced Concrete

Directionally distributed steel fibre-reinforced concrete has been proposed as a novel concrete because of its high tensile strength and crack resistance in specific directions. Based on the existing studies of the effect of the fibre direction on the mechanical properties of fibre-reinforced concrete, the authors in this paper performed further studies of the mechanical properties of directionally distributed steel fibre-reinforced concrete by conducting split tensile and bending tests. The split tensile strength of the directionally distributed fibre-reinforced concrete clearly exhibited anisotropy. The split tensile strength perpendicular to the fibre direction was much higher than that parallel to the fibre direction. The split tensile strength perpendicular to the fibre direction was almost twice the tensile strength of plain concrete. The flexural performance of directionally distributed fibre-reinforced concrete in the fibre direction significantly improved compared to that of randomly distributed fibre-reinforced concrete. Specifically, the flexural strength increased by as much as 97%. Gravity resulted in a deviation in the tensile properties of concrete prepared by manually and directionally placing fibres in a layered casting process. The test results can be utilised in subsequent concrete designs. The conclusions reached in this paper provide comprehensive mechanical design parameters for the application of directionally distributed fibre-reinforced concrete.

Behavioural Study of Steel Fiber and Polypropylene Fibre Reinforced Concrete

2016 ◽  
Vol 708 ◽  
pp. 59-63 ◽  
Author(s):  
Mehmet Alpaslan Köroğlu ◽  
Nebi Özdöner
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Reinforced Concrete ◽  
Steel Fibre ◽  
Steel Fiber ◽  
Plain Concrete ◽  
Polypropylene Fibre ◽  
Fibre Reinforced Concrete ◽  
Steel Fibre Reinforced Concrete ◽  
Behavioural Study

Fibres are generally used as resistance of cracking and strengthening of concrete. The purpose of this research is to investigate the strength and mechanical properties of plain concrete, steel fibre reinforced concrete and polypropylene fibre reinforced concrete. The main focus of this investigation is to understand the reinforcement material’s behaviour on concrete and to compare the effect of increasing fibres on the concrete. The percentages of fibre used for both types of concrete were 0.5%, 1%, 1.5% and 2%. Details and results of the experimental study are provided and discussed.

Adding an expansive agent to increase the toughness of steel fibre reinforced concrete

2019 ◽  
Vol 26 (4) ◽  
pp. 197-208
Author(s):  
Leo Gu Li ◽  
Albert Kwok Hung Kwan
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
The Other ◽  
Fibre Reinforced Concrete ◽  
Test Results ◽  
Compressive Properties ◽  
Shrinkage Cracking ◽  
Steel Fibre Reinforced Concrete ◽  
Expansive Agent ◽  
Concrete Matrix

Previous research studies have indicated that using fibres to improve crack resistance and applying expansive agent (EA) to compensate shrinkage are both effective methods to mitigate shrinkage cracking of concrete, and the additions of both fibres and EA can enhance the other performance attributes of concrete. In this study, an EA was added to fibre reinforced concrete (FRC) to produce concrete mixes with various water/binder (W/B) ratios, steel fibre (SF) contents and EA contents for testing of their workability and compressive properties. The test results showed that adding EA would slightly increase the superplasticiser (SP) demand and decrease the compressive strength, Young’s modulus and Poisson’s ratio, but significantly improve the toughness and specific toughness of the steel FRC produced. Such improvement in toughness may be attributed to the pre-stress of the concrete matrix and the confinement effect of the SFs due to the expansion of the concrete and the restraint of the SFs against such expansion.

Structural performance of steel fibre reinforced concrete — Part IV. Toughness properties

2014 ◽  
Vol 5 (2) ◽  
pp. 119-125
Author(s):  
I. Kovács
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
Fibre Orientation ◽  
Reinforced Concrete Beams ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Flexural Toughness ◽  
Steel Fibre Reinforced Concrete ◽  
Set Up ◽  
Flexural Tests

The present paper of a series deals with the experimental characterisation of flexural toughness properties of structural concrete containing different volume of hooked-end steel fibre reinforcement (75 kg/m3, 150 kg/m3). Third-point flexural tests were carried out on steel fibre reinforced concrete beams having a cross-section of 80 mm × 85 mm with the span of 765 mm, hence the shear span to depth ratio was 3. Beams were sawn out of steel fibre reinforced slab elements (see Part I) in order to take into consideration the introduced privilege fibre orientation (I and II) and the position of the beam (Ba-a, Ba-b, Ba-c) before sawing (see Part I). Flexural toughness properties were determined considering different standard specifications, namely the method of the ASTM (American Standards for Testing Materials), the process of the JSCE (Japan Society of Civil Engineering), and the final proposal of Banthia and Trottier for the post cracking strength. Consequently, behaviour of steel fibre reinforced concrete was examined in bending taking into consideration different experimental parameters such as fibre content, concrete mix proportions, fibre orientation, positions of test specimens in the formwork, while experimental constants were the size of specimens, the type of fibre used and the test set-up and test arrangement.

Bending Strength of Steel Fibre Reinforced Concrete Ribbed Slab Panel

2018 ◽  
Vol 15 (1) ◽  
pp. 15
Author(s):  
AMIR SYAFIQ SAMSUDIN ◽  
MOHD HISBANY MOHD HASHIM ◽  
SITI HAWA HAMZAH ◽  
AFIDAH ABU BAKAR
Keyword(s):  
Reinforced Concrete ◽  
Bending Strength ◽  
Steel Fibre ◽  
Concrete Slab ◽  
Future Application ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Conventional Concrete ◽  
Steel Fibre Reinforced Concrete ◽  
Bending Load

Nowadays, demands in the application of fibre in concrete increase gradually as an engineering material. Rapid cost increment of material causes the increase in demand of new technology that provides safe, efficient and economical design for the present and future application. The introduction of ribbed slab reduces concrete materials and thus the cost, but the strength of the structure also reduces due to the reducing of material. Steel fibre reinforced concrete (SFRC) has the ability to maintain a part of its tensile strength prior to crack in order to resist more loading compared to conventional concrete. Meanwhile, the ribbed slab can help in material reduction. This research investigated on the bending strength of 2-ribbed and 3-ribbed concrete slab with steel fibre reinforcement under static loading with a span of 1500 mm and 1000 mm x 75 mm in cross section. An amount of 40 kg/m steel fibre of all total concrete volume was used as reinforcement instead of conventional bars with concrete grade 30 N/mm2. The slab was tested under three-point bending. Load versus deflection curve was plotted to illustrate the result and to compare the deflection between control and ribbed slab. This research shows that SFRC Ribbed Slab capable to withstand the same amount of load as normal slab structure, although the concrete volume reduces up to 20%.

scholarly journals Fracture and Size Effect of PFRC Specimens Simulated by Using a Trilinear Softening Diagram: A Predictive Approach

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3795
Author(s):  
Fernando Suárez ◽  
Jaime C. Gálvez ◽  
Marcos G. Alberti ◽  
Alejandro Enfedaque
Keyword(s):  
Reinforced Concrete ◽  
Size Effect ◽  
A Priori ◽  
Plain Concrete ◽  
Specimen Size ◽  
Bending Test ◽  
Orientation Factor ◽  
Fibre Reinforced Concrete ◽  
Softening Function ◽  
Three Point Bending

The size effect on plain concrete specimens is well known and can be correctly captured when performing numerical simulations by using a well characterised softening function. Nevertheless, in the case of polyolefin-fibre-reinforced concrete (PFRC), this is not directly applicable, since using only diagram cannot capture the material behaviour on elements with different sizes due to dependence of the orientation factor of the fibres with the size of the specimen. In previous works, the use of a trilinear softening diagram proved to be very convenient for reproducing fracture of polyolefin-fibre-reinforced concrete elements, but only if it is previously adapted for each specimen size. In this work, a predictive methodology is used to reproduce fracture of polyolefin-fibre-reinforced concrete specimens of different sizes under three-point bending. Fracture is reproduced by means of a well-known embedded cohesive model, with a trilinear softening function that is defined specifically for each specimen size. The fundamental points of these softening functions are defined a priori by using empirical expressions proposed in past works, based on an extensive experimental background. Therefore, the numerical results are obtained in a predictive manner and then compared with a previous experimental campaign in which PFRC notched specimens of different sizes were tested with a three-point bending test setup, showing that this approach properly captures the size effect, although some values of the fundamental points in the trilinear diagram could be defined more accurately.

Sign in / Sign up

Export Citation Format

Share Document