Design and Fabrication of PDMS/PMMA-Based Rotary Micropump

2016 ◽  
Vol 829 ◽  
pp. 29-34 ◽  
Author(s):  
Lung Ming Fu ◽  
Wen Teng Wang ◽  
Chia Yen Lee
Keyword(s):  
Flow Rate ◽  
Rotational Velocity ◽  
Maximum Flow ◽  
Maximum Flow Rate ◽  
Engine Oil ◽  
Working Fluid ◽  
Flow Rates ◽  
Peristaltic Pumping ◽  
Velocity Flow ◽  
Pdms Microchannel

A novel micropump is proposed comprising a PMMA-based rotor, a circular PDMS micro-chamber, and a semi-circular PDMS microchannel connecting the inlet and outlet reservoirs as the rotor spins, a plug of sample fluid is trapped within the microchannel between neighboring blades of the rotor and is driven through the channel toward the outlet. Meanwhile, the rotors periodically compress and release the inlet and outlet regions of the microchannel. Thus, as the rotor turns, one plug of sample fluid is drawn into the microchannel as another is ejected into the outlet reservoir. In other words, a peristaltic pumping effect is achieved. It is shown that the flow rate in the proposed device can be controlled simply by adjusting the rotational velocity of the rotor. A maximum flow rate of 1.22 ml/min is obtained given de-ionized water as the working fluid and a rotational velocity of 232 rpm. Moreover, given the same rotational velocity, flow rates of 0.724 ml/min and 0.336 ml/min are obtained for salad oil and engine oil, respectively.

scholarly journals High Flow-Rate Sample Loading in Large Volume Whole Water Organic Trace Analysis Using Positive Pressure and Finely Ground Sand as a SPE-Column In-Line Filter

Molecules ◽  
2019 ◽  
Vol 24 (7) ◽  
pp. 1426
Author(s):  
Ola Svahn ◽  
Erland Björklund
Keyword(s):  
Physicochemical Properties ◽  
Flow Rate ◽  
Solid Phase ◽  
Pure Water ◽  
Maximum Flow ◽  
Maximum Flow Rate ◽  
Positive Pressure ◽  
Flow Rates ◽  
Relative Standard ◽  
Whole Water

By using an innovative, positive pressure sample loading technique in combination with an in-line filter of finely ground sand the bottleneck of solid phase extraction (SPE) can be reduced. Recently published work by us has shown the proof of concept of the technique. In this work, emphasis is put on the SPE flow rate and method validation for 26 compounds of emerging environmental concern, mainly from the 1st and 2nd EU Watch List, with various physicochemical properties. The mean absolute recoveries in % and relative standard deviations (RSD) in % for the investigated compounds from spiked pure water samples at the three investigated flow rates of 10, 20, and 40 mL/min were 63.2% (3.2%), 66.9% (3.3%), and 69.0% (4.0%), respectively. All three flow rates produced highly repeatable results, and this allowed a flow rate increase of up to 40 mL/min for a 200 mg, 6 mL, reversed phase SPE cartridge without compromising the recoveries. This figure is more than four times the maximum flow rate recommended by manufacturers. It was indicated that some compounds, especially pronounced for the investigated macrolide molecules, might suffer when long contact times with the sample glass bottle occurs. A reduced contact time somewhat decreases this complication. A very good repeatability also held true for experiments on both spiked matrix-rich pond water (high and low concentrations) and recipient waters (river and wastewater) applying 40 mL/min. This work has shown that, for a large number of compounds of widely differing physicochemical properties, there is a generous flow rate window from 10 to 40 mL/min where sample loading can be conducted. A sample volume of 0.5 L, which at the recommended maximum flow rate speed of 10 mL/min, would previously take 50 min, can now be processed in 12 min using a flow rate of 40 mL/min. This saves 38 min per processed sample. This low-cost technology allows the sample to be transferred to the SPE-column, closer to the sample location and by the person taking the sample. This further means that only the sample cartridge would need to be sent to the laboratory, instead of the whole water sample, like today’s procedure.

Lichen sclerosis–induced long segment anterior urethral stricture: The early outcome of one-stage repair using dorsolateral onlay buccal mucosa graft

2021 ◽  
pp. 039156032110033
Author(s):  
Atef Fathi ◽  
Omar Mohamed ◽  
Osama Mahmoud ◽  
Gamal A Alsagheer ◽  
Ahmed M Reyad ◽  
...  
Keyword(s):  
Success Rate ◽  
Urethral Stricture ◽  
Flow Rate ◽  
Urine Volume ◽  
Maximum Flow ◽  
Maximum Flow Rate ◽  
P Value ◽  
Onlay Graft ◽  
Voiding Symptoms ◽  
Stricture Recurrence

Background: Substitution urethroplasty using buccal mucosal grafts can be performed by several approaches including ventral onlay graft, dorsal onlay graft, or ventral urethrotomy with dorsal inlay graft. Our study aims to evaluate the surgical outcome of dorsolateral buccal mucosal graft for long segment anterior urethral stricture >6 cm in patients with Lichen sclerosus (LS). Methods: A retrospective study included patients who underwent repair for long segment anterior urethral stricture >6 cm due to LS between January 2013 and April 2019. All patients were followed-up at 3, 6, 9, and 12 months postoperatively and then yearly by clinical symptoms, uroflowmetry, and calculation of post-void residual urine volume. Retrograde urethrogram was requested for patients with voiding symptoms or decreased maximum flow rate. Stricture recurrence that required subsequent urethrotomy or urethroplasty was considered failure. The success rate and surgical complications were collected and analyzed. Results: Thirty patients were identified. The median age (range) was 39 (25–61) years and a median (range) stricture length was 8 (6–14) cm. Most of postoperative complications were of minor degree. The success rate at median follow-up of 15 (12–24) months was 86.5%. The median maximum flow rate increased significantly from 6 (2–11) ml/s preoperatively to 18 (range: 6–23) ml/s at the 6th month ( p value < 0.001). Conclusion: Dorsolateral buccal mucosal grafts urethroplasty for long anterior urethral stricture caused by LS has a high success rate and low risk of complications including stricture recurrence.

scholarly journals Improving Output Performance of a Resonant Piezoelectric Pump by Adding Proof Masses to a U-Shaped Piezoelectric Resonator

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 500
Author(s):  
Jian Chen ◽  
Wenzhi Gao ◽  
Changhai Liu ◽  
Liangguo He ◽  
Yishan Zeng
Keyword(s):  
Flow Rate ◽  
Maximum Flow ◽  
Working Fluid ◽  
Driving Voltage ◽  
Piezoelectric Resonator ◽  
Piezoelectric Pump ◽  
Compact Structure ◽  
Output Performance ◽  
Volume Efficiency ◽  
Working Efficiency

This study proposes the improvement of the output performance of a resonant piezoelectric pump by adding proof masses to the free ends of the prongs of a U-shaped piezoelectric resonator. Simulation analyses show that the out-of-phase resonant frequency of the developed resonator can be tuned more efficiently within a more compact structure to the optimal operating frequency of the check valves by adjusting the thickness of the proof masses, which ensures that both the resonator and the check valves can operate at the best condition in a piezoelectric pump. A separable prototype piezoelectric pump composed of the proposed resonator and two diaphragm pumps was designed and fabricated with outline dimensions of 30 mm × 37 mm × 54 mm. Experimental results demonstrate remarkable improvements in the output performance and working efficiency of the piezoelectric pump. With the working fluid of liquid water and under a sinusoidal driving voltage of 298.5 Vpp, the miniature pump can achieve the maximum flow rate of 2258.9 mL/min with the highest volume efficiency of 77.1% and power consumption of 2.12 W under zero backpressure at 311/312 Hz, and the highest backpressure of 157.3 kPa under zero flow rate at 383 Hz.

scholarly journals Maximum Flow Rate of a Single Component, Two-Phase Mixture

1965 ◽  
Vol 87 (1) ◽  
pp. 134-141 ◽  
Author(s):  
F. J. Moody
Keyword(s):  
Flow Rate ◽  
Static Pressure ◽  
Maximum Flow ◽  
Single Component ◽  
Maximum Flow Rate ◽  
Vapor Flow ◽  
Two Phase ◽  
Slip Ratio ◽  
Phase Mixture ◽  
Local Slip

A theoretical model is developed for predicting the maximum flow rate of a single component, two-phase mixture. It is based upon annular flow, uniform linear velocities of each phase, and equilibrium between liquid and vapor. Flow rate is maximized with respect to local slip ratio and static pressure for known stagnation conditions. Graphs are presented giving maximum steam/water flow rates for: local static pressures between 25 and 3,000 psia, with local qualities from 0.01 to 1.00; local stagnation pressures and enthalpies which cover the range of saturation states.

Effect of Blade Angle of Attack and Hub to Tip Ratio on Mass Flow Rate in an Axial Fan at a Fixed Rotational Speed

2008 ◽  
Author(s):  
Mohammad J. Izadi ◽  
Alireza Falahat
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Angle Of Attack ◽  
Maximum Flow ◽  
Maximum Flow Rate ◽  
Maximum Mass ◽  
Blade Angle ◽  
Axial Fan

In this investigation an attempt is made to find the best hub to tip ratio, the maximum number of blades, and the best angle of attack of an axial fan with flat blades at a fixed rotational speed for a maximum mass flow rate in a steady and turbulent conditions. In this study the blade angles are varied from 30 to 70 degrees, the hub to tip ratio is varied from 0.2 to 0.4 and the number of blades are varied from 2 to 6 at a fixed hub rotational speed. The results show that, the maximum flow rate is achieved at a blade angle of attack of about 45 degrees for when the number of blades is set equal to 4 at most rotational velocities. The numerical results show that as the hub to tip ratio is decreased, the mass flow rate is increased. For a hub to tip ratio of 0.2, and an angle of attack around 45 degrees with 4 blades, a maximum mass flow rate is achieved.

The characters exploration of a piezoelectric pump with fishtail-shaped bluffbody

2021 ◽  
pp. 1045389X2110386
Author(s):  
Yi Hou ◽  
Lipeng He ◽  
Zheng Zhang ◽  
Baojun Yu ◽  
Hong Jiang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Preliminary Investigation ◽  
Maximum Flow ◽  
Theoretical Explanation ◽  
Maximum Flow Rate ◽  
Bluff Bodies ◽  
Conical Flow ◽  
Piezoelectric Pump ◽  
Valveless Piezoelectric Pump ◽  
Shape And Size

This paper focuses on a new structure in the valveless piezoelectric pump, which has a combination structure of the conical flow channel and two fishtail-shaped bluffbodies in the chamber of the pump. The fishtail-shaped bluffbody is inspired by the shape of the swimming fish to diminish the backflow and optimize the performance of the pump. The performance is studied by changing the shape and size of the inlet and outlet, the bluff bodies’ height and the space between two bluff bodies. The results show that the 3 mm × 3 mm square inlet, 3 mm diameter round outlet, 3 mm height of bluffbodies, 6.8 mm pitch of bluffbodies has a best performance in all 10 prototypes, which implements a maximum flow rate of 87.5 ml/min at 170 V 40 Hz with a noise of 42.6 dB. This study makes a preliminary investigation and theoretical explanation for the subsequent optimization of this structure, improved the performance of the valveless piezoelectric pump, broaden the thinking of the design for the bluffbody for better performance of the valveless piezoelectric pump.

Transport of Particle-Laden Fluids Through Fixed-Valve Micropumps

1999 ◽  
Author(s):  
Ling-Sheng Jang ◽  
Christopher J. Morris ◽  
Nigel R. Sharma ◽  
Ron L. Bardell ◽  
Fred K. Forster
Keyword(s):  
Surface Charge ◽  
Surface Area ◽  
Flow Rate ◽  
Pure Water ◽  
Maximum Flow ◽  
Total Surface Area ◽  
Maximum Flow Rate ◽  
Number Density ◽  
Polystyrene Microspheres ◽  
Negative Surface

Abstract Micropumps designed for the flow-rate range of 100–1000μl/min have been developed by a number of research groups. However, little data is available regarding the ability of various designs to directly transport liquids containing particles such as cells, microspheres utilized for bead chemistry, or contaminants. In this study the ability of pumps with no-moving-parts valves (NMPV) to transport particles was investigated. The results showed that a NMPV micropump was able to directly pump suspensions of polystyrene microspheres from 3.1 to 20.3μm in diameter. The pump functioned without clogging at microsphere number densities as high as 9000 particles/μl of suspension, which corresponded to over 90,000 particles per second passing through the pump at a flow rate of 600μl/min. Performance with polystyrene microspheres was the same as pure water up to the point of cavitation. Microspheres manufactured with negative surface charge cavitated less readily that other microspheres studied that were manufactured without surface charge. However, cavitation did not appear to be a function of microsphere size, total surface area or number density. Thus pumping polystyrene microspheres was found to be more affected by surface effects than by size, surface area or number density within the range of parameters considered. In the case of charged microspheres, the maximum flow rate was reduced by 30% compared to pure water whereas for uncharged microspheres the maximum flow rate was reduced by approximately 80%.

Sign in / Sign up

Export Citation Format

Share Document