Experimental Research on Mechanical Properties of the early-Age Shotcrete

2011 ◽  
Vol 90-93 ◽  
pp. 2188-2192
Author(s):  
Nan Xie ◽  
Jie Ouyang ◽  
Bing Li ◽  
Jing Hui Lu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Experimental Research ◽  
Early Age ◽  
Construction Sites ◽  
Exponential Relationship ◽  
Construction Period ◽  
Ordinary Concrete ◽  
Under Construction

Abstract. The compressive strength and elastic modulus of early-age shotcrete have important influence on the safety of tunnel during construction period. In order to investigate the laws of the mechanical properties of early-age shotcrete, experiments on the compressive strength and elastic modulus of early-age shotcrete with two different mixes used frequently on construction sites were carried out. The results show that the compressive strength and elastic modulus of shotcrete develop fairly rapidly and especially the development of elastic modulus of shotcrete is faster than that of ordinary concrete. There is an exponential relationship between the compressive strength and time as well as the elastic modulus development and time. Simultaneously their formulas were derived. The research results of this paper are not only helpful to understand the laws of the mechanical properties of early-age shotcrete, but also provide some reference for the reliability analysis of tunnel under construction.

Evaluation of Relations among Basic Mechanical Properties of Concrete with Machine-Made Sand

2011 ◽  
Vol 418-420 ◽  
pp. 441-444 ◽  
Author(s):  
Feng Lan Li ◽  
Yan Zeng ◽  
Chang Yong Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Rough Surface ◽  
Design Code ◽  
Ordinary Concrete ◽  
Axial Compressive Strength ◽  
Different Characteristics

Due to many different characteristics such as irregular polygon particle with pointed edges, rough surface and larger content of stone powder, machine-made sand has ignorable effects on the properties of concrete. As the basis for the design of concrete structures, the relations among the basic mechanical properties of concrete such as compressive strength, tensile strength, flexural strength and elastic modulus should be clearly understood. This paper summarizes the test data from the published references, and discusses the relations among these properties by statistical analyses compared with those of ordinary concrete. The results show that the axial compressive strength and the tensile strength can be prospected by the same formulas of ordinary concrete specified in current Chinese design code, but the prospected tensile strength should multiply a reducing coefficient when the strength grade of concrete is lower than C30. The elastic modulus of concrete with machine-made sand is larger than that of ordinary concrete, which should be prospect by the formula in this paper. Meanwhile, the formula of flexural strength is suggested.

Evaluation of Relations among Basic Mechanical Properties of Fly-Ash Concrete with Machine-Made Sand

2013 ◽  
Vol 438-439 ◽  
pp. 15-19
Author(s):  
Chun Jie Liu ◽  
Chun Yan Jia ◽  
Chang Yong Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Concrete Structures ◽  
Ordinary Concrete ◽  
Strength Grade ◽  
Fly Ash Concrete ◽  
Axial Compressive Strength

Although the machine-made sand was widely used for concrete in recent years in China, it was short of studies on the relations among the basic mechanical properties of fly-ash concrete with machine-made sand (MSFAC). However, these relations such as the compressive strength, the tensile strength and the elastic modulus with the cubic compressive strength (i.e. strength grade) are the basis of design for concrete structures. This paper summarizes the test data from the published references, and discusses the relations among these properties by statistical analyses compared with those of ordinary concrete. The results show that only the tensile strength of MSFAC can be safely forecasted by the same formula of ordinary concrete specified in current Chinese design code. When the strength grade is higher than C45, the axial compressive strength of MSFAC is largely forecasted by the formula of ordinary concrete. The elastic modulus of MSFAC is larger than that of ordinary concrete, which should be prospect by the formula in this paper. This work gives out some cautions for the proper use of the MSFAC in concrete structures.

The Experimental Study of Early-Age Strength and Elastic Modulus of Concrete

2010 ◽  
Vol 163-167 ◽  
pp. 1192-1197 ◽  
Author(s):  
Deng Xiang Zhang ◽  
Wei Jun Yang
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Elastic Modulus ◽  
Statistical Analysis ◽  
Coefficient Of Variation ◽  
Early Age ◽  
Good Prediction ◽  
Construction Period ◽  
Large Numbers ◽  
Safety And Reliability

Based on large numbers of experiment results, this paper carries out statistical analysis and proposes the probability distribution properties of the random process of strength and elastic modulus and their coefficient of variation, and develops a new prediction model of early-age strength and elastic modulus and their coefficient of variation respectively. The model can provide good prediction of the development of mechanical properties of concrete structures in aging, and it is important to evaluate the concrete structure safety and reliability in the construction period.

Compressive Strength Properties of Fly Ash-Based Geopolymer Concrete

2013 ◽  
Vol 741 ◽  
pp. 49-54 ◽  
Author(s):  
Gum Sung Ryu ◽  
Gi Hong Ahn ◽  
Kyung Taek Koh ◽  
Jang Hwa Lee
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Ordinary Portland Cement ◽  
Mechanical Characteristics ◽  
Strength Properties ◽  
Early Age ◽  
Geopolymer Concrete ◽  
Test Results ◽  
Ordinary Concrete

This study intends to investigate experimentally the mechanical characteristics of the compressive strength and elastic modulus of concrete using 3 types of binder that are ordinary Portland cement, fly ash and physically milled fly ash. The test results show that the compressive strength and elastic modulus of the cement-zero concrete reached respectively 30.0 MPa and 19.1 GPa, and indicated that more than 90% of the strength was developed at early age. In addition, a comparison of the geopolymer concrete with ordinary concrete enabled to derive and suggest formulaeexpressing the elastic modulus in function of the compressive strength.

scholarly journals Experimental Analysis of the Mechanical Properties and Resistivity of Tectonic Coal Samples with Different Particle Sizes

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2303
Author(s):  
Congyu Zhong ◽  
Liwen Cao ◽  
Jishi Geng ◽  
Zhihao Jiang ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Coalbed Methane ◽  
Coal Sample ◽  
Fine Particles ◽  
Particle Sizes ◽  
Tectonic Coal

Because of its weak cementation and abundant pores and cracks, it is difficult to obtain suitable samples of tectonic coal to test its mechanical properties. Therefore, the research and development of coalbed methane drilling and mining technology are restricted. In this study, tectonic coal samples are remodeled with different particle sizes to test the mechanical parameters and loading resistivity. The research results show that the particle size and gradation of tectonic coal significantly impact its uniaxial compressive strength and elastic modulus and affect changes in resistivity. As the converted particle size increases, the uniaxial compressive strength and elastic modulus decrease first and then tend to remain unchanged. The strength of the single-particle gradation coal sample decreases from 0.867 to 0.433 MPa and the elastic modulus decreases from 59.28 to 41.63 MPa with increasing particle size. The change in resistivity of the coal sample increases with increasing particle size, and the degree of resistivity variation decreases during the coal sample failure stage. In composite-particle gradation, the proportion of fine particles in the tectonic coal sample increases from 33% to 80%. Its strength and elastic modulus increase from 0.996 to 1.31 MPa and 83.96 to 125.4 MPa, respectively, and the resistivity change degree decreases. The proportion of medium particles or coarse particles increases, and the sample strength, elastic modulus, and resistivity changes all decrease.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

Fabrication and Mechanical Properties of Dense/Porous β-Tricalcium Phosphate Bioceramics

2007 ◽  
Vol 330-332 ◽  
pp. 907-910
Author(s):  
Fa Ming Zhang ◽  
Jiang Chang ◽  
Jian Xi Lu ◽  
Kai Li Lin
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Exponential Growth ◽  
Weight Bearing ◽  
Area Ratio ◽  
Sectional Area ◽  
Cross Sectional ◽  
The Matrix ◽  
Porous Bioceramics

Attempt to increase the mechanical properties of porous bioceramics, a dense/porous structured β-TCP bioceramics that mimic the characteristics of nature bone were fabricated. Experimental results show that the dense/porous structured β-TCP bioceramics demonstrated excellent mechanical properties with compressive strength up to 74 MPa and elastic modulus up to 960 MPa, which could be tailored by the dense/porous cross-sectional area ratio obeying the rule of exponential growth. The interface between the dense and porous bioceramics is connected compactly and tightly with some micropores distributed in the matrix of both porous and dense counterparts. The dense/porous structure of β-TCP bioceramics may provide an effective way to increase the mechanical properties of porous bioceramics for bone regeneration at weight bearing sites.

Mechanical Properties of Carbon Cathodes during Aluminium Electrolysis

2011 ◽  
Vol 399-401 ◽  
pp. 2155-2159
Author(s):  
Qing Sheng Liu ◽  
Hui Fang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Great Influence ◽  
Strain Curve ◽  
Experimental Simulation ◽  
Ambient Conditions ◽  
Aluminium Electrolysis ◽  
Electrolysis Condition ◽  
Carbon Cathode

Based on the service ambient with aluminium electrolysis condition, the evolution of compressive strength, elastic modulus and stress-strain curve of carbon cathode samples under various conditions are investigated by experimental simulation method; the deterioration mechanism of the mechanical of carbon cathode is also studied. Results show that different carbon cathode materials and ambient conditions have great influence on strength and elastic modulus of carbon cthode. The mechanical properties such as compressive strength and elastic modulus of carbon catodes can be degraded by the erosion of sodium and molten salt during aluminium electrolysis, that has been confirmation by the SEM and XRD analysis.

Experimental Study on Mechanical Properties of Fine Aggregate Concrete Made after Wet-Sieving Coarse Aggregate

2010 ◽  
Vol 168-170 ◽  
pp. 2200-2203 ◽  
Author(s):  
Shun Bo Zhao ◽  
Na Liang ◽  
Li Xin Liu ◽  
Li Sun ◽  
Su Yang
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Coarse Aggregate ◽  
Fine Aggregate ◽  
Concrete Wall ◽  
Aggregate Concrete ◽  
Structural Wall ◽  
Ordinary Concrete ◽  
Reinforced Composite ◽  
Wet Sieving

The validity of the wet-sieving concrete technique for building the reinforced composite concrete wall are demonstrated in the paper. The fine aggregate concrete made by ordinary concrete passing the sieve with square mash of 15 mm was cast for the surface layer, the recomposed concrete mixed by the residual concrete stayed on the sieve with the ordinary concrete was cast for the reinforced concrete structural wall. The mechanical properties such as the cubic and compressive strengths, the elastic modulus and the splitting and flexural tensile strengths of the fine aggregate concrete, the recomposed concrete and the ordinary concrete were tested and analyzed. The results show that the elastic modulus and splitting tensile strength of fine aggregate concrete reduce in some extent compared with that of ordinary concrete, the mechanical properties of recomposed concrete are almost the same as that of ordinary concrete.

Comparative experimental study on physical and mechanical properties of quartz sandstone after water-cooling and natural-cooling under high temperature

2021 ◽  
pp. qjegh2020-181
Author(s):  
Haopeng Jiang ◽  
Annan Jiang ◽  
Fengrui Zhang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Heating Temperature ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Water Cooling ◽  
Average Value ◽  
Cooling Methods

Experimental tests were conducted to study the influence of natural cooling and water cooling on the physical and mechanical properties of quartz sandstone. This study aims to understand the effect of different cooling methods on the physical and mechanical properties of quartz sandstone (such as mass, volume, density, P-wave velocity, elastic modulus, uniaxial compressive strength, etc.). The results show that the uniaxial compressive strength (UCS) and elastic modulus(E) of the specimens cooled by natural-cooling and water-cooling decrease with heating temperature. At 800℃, after natural cooling and water cooling, the average value of UCS decreased by 34.65% and 57.90%, and the average value of E decreased by 87.66% and 89.05%, respectively. Meanwhile, scanning electron microscope (SEM) images were used to capture the development of microcracks and pores within the specimens after natural-cooling and water-cooling, and it was found that at the same temperature, water cooling treatment was more likely to cause microcracks and pores, which can cause more serious damage to the quartz sandstone. These results confirm that different cooling methods have different effects on the physical and mechanical properties of quartz sandstone, and provide a basis for the stability prediction of rock mass engineering such as tunnel suffering from fire.

Sign in / Sign up

Export Citation Format

Share Document