One-Year Sulfate Attack on Various Types of Fine Grained Concrete

2015 ◽  
Vol 1124 ◽  
pp. 313-318
Author(s):  
Martin Vyšvařil ◽  
Markéta Rovnaníková
Keyword(s):  
Sulfuric Acid ◽  
Acid Corrosion ◽  
Surrounding Medium ◽  
Mineralogical Composition ◽  
Sulfate Solution ◽  
Xrd Analysis ◽  
Sewage Water ◽  
Sulfate Attack ◽  
Fine Grained ◽  
Ph Decrease

Concrete shows extensive degradation when exposed to the external sulfate attack, characterized by ingress of sulfate ions from surrounding medium. This process leads to gradual pH decrease, to expansion, cracking, spalling of concrete, and finally to the complete disintegration of the material. Sulfate attack becomes a major destructor in sewage collection systems where the concrete sewer pipes are exposed to sulfates from wastewater as well as from biogenic activity of bacteria. This paper is focused on the sulfate attack on fine grained concrete where the effect of 0.5% sulfuric acid, simulating biogenic sulfuric acid corrosion, 5% sodium sulfate solution and solution simulating sewage water on various types of concrete has been investigated. The concrete specimens were characterized after exposition to corroding media by their mechanical parameters, microstructure and in the case of H2SO4 as the most aggressive corroding solution, the mineralogical composition was also determined by XRD analysis. It was found that the exposition to Na2SO4 solution twofold improved flexural strengths of concrete mixes based on Portland and sulfate-resisting cements. Contrary, the exposition to H2SO4 solution significantly decreased compressive strengths of all types of concrete.

Sulfate Attack on Different Types of Concrete in Media Simulating Sewer System

2016 ◽  
Vol 714 ◽  
pp. 122-127
Author(s):  
Martin Vyšvařil ◽  
Markéta Rovnaníková ◽  
Patrik Bayer
Keyword(s):  
Waste Water ◽  
Sulfuric Acid ◽  
Sewage Water ◽  
Sulfate Attack ◽  
Acid Attack ◽  
Bottom Part ◽  
Sewer Pipes ◽  
Fine Grained ◽  
Different Types ◽  
One Year

The degradation of concrete due to ingress of sulfate ions from the environment plays an important role in the durability of concrete constructions. Microbiologically induced concrete corrosion (MICC) damages especially sewage collection systems. The most rapid cases of deterioration always occur in areas with elevated H2S concentrations, moisture, and oxygen in the atmosphere. During the MICC, the pH of the surface of concrete sewer pipes is reduced and it may lead to the steel depassivation and results in the corrosion of steel reinforcement. Damage due to a sulfate interaction can result in a cracking and softening, with a loss of strength of concrete. The formation of ettringite (AFt) from gypsum (forming by reaction of sulfate anion with calcium hydroxide) and C3A via monosulfate (AFm) is the main chemical reaction of sulfate attack on concrete. Ettringite and gypsum have considerably larger volume than initial compounds, which leads to increased pressure in concrete. This paper is focused on the sulfate attack on fine-grained concrete where the effect of 0.5% sulfuric acid, simulating MICC, and a solution simulating sewage water has been investigated on changes of the pH, content of sulfates and the porosity in various types of concrete. The aim of this study is to compare the changes in different types of concrete during the sulfate attack in two kinds of medium represented the bottom part of pipelines (waste water) and the sewer crown (0.5% H2SO4). It was found, that after 1 year in 0.5% H2SO4, a visible degradation of surface occurs in all investigated types of concrete. Samples over the year in waste water became dark. Concentration of sulfates in all studied types of concrete increased six times at least after one year sulfuric acid attack and also the reduction of the pH of their aqueous leaches was determined. The solution simulating sewage water did not cause such changes.

Sulfuric Acid Attack on Various Types of Fine Grained Concrete

2015 ◽  
Vol 1100 ◽  
pp. 101-105
Author(s):  
Martin Vyšvařil ◽  
Markéta Rovnaníková
Keyword(s):  
Sulfuric Acid ◽  
Acid Corrosion ◽  
Sulfate Attack ◽  
Steel Reinforcement ◽  
Acid Attack ◽  
Sewer Pipes ◽  
Sulfate Ions ◽  
Fine Grained ◽  
Ph Values ◽  
Sulfuric Acid Corrosion

Sulfate corrosion is one of the major threats for durability of concrete constructions and it becomes a major destructor in sewage collection systems where the concrete sewer pipes are exposed to sulfates from wastewater as well as from biogenic activity of bacteria. During this process the pH of the surface of concrete sewer pipes is reduced and it may lead to steel depassivation and results in the corrosion of this steel reinforcement. This paper is focused on the sulfate attack on fine grained concrete where the effect of 0.5% sulfuric acid, simulating biogenic sulfuric acid corrosion, on changes of pH and content of sulfates in various types of concrete has been investigated. After 3 and 6 months of the corrosive treatment, the content of sulfate ions and pH values in several layers of specimens were determined. It was found that the sulfate ions penetrate into concrete to the maximum depth of 20 mm and the pH of the aqueous leaches of particular layers of the samples was reduced to 11.4 at the most. Thus, the conditions for the depassivation of reinforcement were not met. The GL and GBFS concrete samples showed the least changes of their pH and therefore they had the best resistivity to the six months sulfate attack.

Study of Fine-Grained Composites Exposed to Sulfuric Acid and Sodium Sulfate

2016 ◽  
Vol 827 ◽  
pp. 275-278
Author(s):  
Martin Vyšvařil ◽  
Markéta Rovnaníková
Keyword(s):  
Waste Water ◽  
Sulfuric Acid ◽  
Sodium Sulfate ◽  
Sulfate Attack ◽  
Sewer Pipes ◽  
Sulfate Ions ◽  
Fine Grained ◽  
One Year ◽  
Corrosion Of Steel ◽  
Loss Of Strength

The degradation of concrete due to ingress of sulfate ions from the environment plays an important role in the durability of concrete constructions, especially in sewage collection systems where concrete sewer pipes are exposed to sulfates from waste water and from biogenic activity of bacteria. During this process the pH of the surface of concrete sewer pipes is reduced and it may lead to the steel depassivation and results in the corrosion of steel reinforcement. Damage due to sulfate interaction can result in the cracking and softening, with loss of strength of concrete. This paper is focused on the sulfate attack on fine-grained concrete where the effect of one-year contact of 0.5% H2SO4, and 5% Na2SO4 on changes of pH and content of sulfates in 7 types of concrete has been analyzed. It was found that after one year of sulfate attack on concrete, significant growth of content of sulfates is observed in the lowermost layer of the samples. Samples treated by 5% Na2SO4 contain slightly more sulfates in the upper layers than samples treated by sulfuric acid. The reduction in pH of aqueous leaches occurred in all layers of the samples. However, even in the lower layers of the samples, the reduction of pH below 9.5 did not turn up (except for SRS sample), and thus the conditions for the depassivation of reinforcement were not met.

scholarly journals Sulfuric Acid Resistance of CNT-Cementitious Composites

2021 ◽  
Vol 11 (5) ◽  
pp. 2226
Author(s):  
Gun-Cheol Lee ◽  
Youngmin Kim ◽  
Soo-Yeon Seo ◽  
Hyun-Do Yun ◽  
Seongwon Hong
Keyword(s):  
Sulfuric Acid ◽  
Electrical Properties ◽  
Mechanical Performance ◽  
Cement Mortar ◽  
Acid Corrosion ◽  
Acid Resistance ◽  
Sulfate Attack ◽  
Cementitious Composites ◽  
Sulfuric Acid Solutions ◽  
Single Walled Cnts

This study analyzed changes in the durability characteristics of cement mortar incorporating carbon nanotube (CNT) and the electrical properties subjected to deterioration induced by sulfate attack. Powder types of multi-walled or single-walled CNTs were used and added to the composites with 1.0% and 2.0% mass fraction, and the specimens were immersed in 5% and 10% sulfuric acid solutions to investigate the durability of CNT cementitious composites. Although mechanical performance decreased due to relatively large pores (370–80 μm) caused by CNTs, specimens incorporating CNTs exhibited enhanced resistance to sulfuric acid as CNTs, which offered strong resistance to acid corrosion, and prevented contact between the cement hydrate and the sulfuric acid solution. Therefore, it is expected that self-sensing performance was exhibited because there were no significant differences in the electrical properties of cement mortar subjected to the deterioration by sulfate attack.

scholarly journals Mineralogical Composition and Physical–Mechanical Properties of Dasht-E-Taatrang Zar Sand Deposits (Afghanistan)

2020 ◽  
Vol 5 (1) ◽  
pp. 2
Author(s):  
Hemayatullah Ahmadi ◽  
Atal Yousufi ◽  
Amir Mohammad Mosazai
Keyword(s):  
Mechanical Properties ◽  
Construction Material ◽  
Mineralogical Composition ◽  
Xrd Analysis ◽  
Sample Collection ◽  
Extensive Field ◽  
Chemical And Mineralogical Composition ◽  
New City ◽  
Two Phases ◽  
Field Works

Sand is a common construction material used for various purposes, e.g., concrete, mortar, render, screed, and asphalt. The usage depends on its fineness, and its fineness is controlled by its mineralogical composition and physical-mechanical properties. This research aims to determine the chemical and mineralogical composition and the physical-mechanical properties of the Dasht-e-Taatrang Zar sand deposits within the Qarabagh and Bagram districts of Kabul and Parwan provinces in Afghanistan. To achieve the objectives of this research, a review of the existing literature has been combined with new extensive field works for macroscopic studies and sample collection, and laboratory analyses. In total, 23 samples during two phases of field works were collected and subjected to lab works for XRF, Schlich, and XRD analysis to determine the chemical and mineralogical composition; moreover, sieve and Atterberg analysis, specific gravity, soundness, and alkali-silica reaction tests were performed for characterization of the physical-mechanical properties of the studied samples. The results of the tests show that the Taatrang Zar sand deposits are considered as a suitable construction material, and due to their simple accessibility, the deposits have high potential as a construction material supplier for the Kabul new city project (Dehsabz) in Kabul and adjacent Parwan and Kapisa provinces.

Microwave-Assisted Leaching Vanadium from Stone Coal

2011 ◽  
Vol 189-193 ◽  
pp. 3916-3919 ◽  
Author(s):  
Hong Zhou Ma ◽  
Xin Zhe Lan ◽  
Yao Ning Wang ◽  
Yu Hong Tian
Keyword(s):  
Sulfuric Acid ◽  
Microwave Power ◽  
Orthogonal Design ◽  
Chemical Constituents ◽  
Influence Factors ◽  
Sulfate Solution ◽  
Leaching Rate ◽  
Stone Coal ◽  
Microwave Assisted ◽  
Design Experiments

Technological process of microwave-assisted leaching of vanadium with sulfate solution has been defined on the base of phase and chemical constituents of stone coal. The influence factors such as content of sulfuric acid, microwave power, and leaching time were studied on leaching rate of vanadium from the stone coal. One element experiments and orthogonal design experiments are carried out to achieve optimized parameters. The experimental results showed that the leaching rate of vanadium was improved by the change of influence factors at some range. The single leaching rate of vanadium reached 80.9% under the optimal conditions of sulfuric acid content of 12%, microwave power 539w,leaching time of 2h.

Simulations on Expansive Strain of Concrete Caused by Ettringite Growth under Sulfate Attack

2011 ◽  
Vol 250-253 ◽  
pp. 1906-1911 ◽  
Author(s):  
Xiao Bao Zuo ◽  
Wei Sun
Keyword(s):  
Sulfate Solution ◽  
Sulfate Attack ◽  
Diffusion Time ◽  
Diffusion Reaction ◽  
Sulfate Ion ◽  
Reaction Equation ◽  
Ettringite Formation ◽  
Sulfate Solutions ◽  
Calcium Aluminates ◽  
Strain Responses

In order to assess theoretically the expansive strain of concrete caused by the ettringite formation and growth under the sulfate attack, some models are proposed to investigate the strain responses of concrete exposed to the sulfate solutions. Firstly, an 1-D nonlinear and nonsteady diffusion-reaction equation of sulfate ion in concrete is proposed; Secondly, based on chemical reactions between sulfate and aluminates in concrete, the expansive strain is obtained due to the ettringite growth resulting in concrete expansion. Thirdly, numerical simulations are carried out to analyze the formation process of the concrete expansive strain under the sulfate solution, and results show that the models can be used to predict the concrete responses with the diffusion time, such as the distribution concentration of sulfate ion, dissipated concentration of the calcium aluminates, expansion strain of concrete due to the formation and growth of ettringite.

Deterioration of concrete containing limestone powder exposed to sulfate attack at ambient temperature

2021 ◽  
Vol 11 (5) ◽  
pp. 724-731
Author(s):  
Hemin Liu ◽  
Qian Huang ◽  
Liang Zhao
Keyword(s):  
Ambient Temperature ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Limestone Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mineral Phases ◽  
Adverse Influence ◽  
Powder Content ◽  
Scanning Electron

This study investigates the deterioration of concrete containing limestone powder exposed to sulfate solution under ambient temperature (20~25 °C). Microstructure and mineral phases within the attacked concrete were measured by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). It was found that the addition of limestone powder increased the initial porosity of concrete. Consequently, a larger amount of SO2–4 ions diffused into the concrete containing limestone powder, and their degree of deterioration caused by sulfate attack increased with the increase in limestone powder content. At ambient temperature, gypsum and ettringite were the major attack products, respectively within the surface and nearsurface portions of concrete containing limestone powder, which was consistent with the products of sulfate attack within concrete without limestone powder. Therefore, the type and distribution of the attack products in concrete had not been revised due to the addition of limestone powder. Nevertheless, the adverse influence of limestone powder on the sulfate resistance of concrete, even at ambient temperature, should be considered. Furthermore, effective measures should be implemented to improve the durability of concrete containing limestone powder in this environment.

Sign in / Sign up

Export Citation Format

Share Document