Cutting Force Analysis when Milling Ti-6Al-4V under Dry and Near Dry Conditions Using Coated Tungsten Carbides

2010 ◽  
Vol 129-131 ◽  
pp. 993-998 ◽  
Author(s):  
M.S. Ahmad Yasir ◽  
C.H. Che Hassan ◽  
A.G. Jaharah ◽  
M. Norhamidi ◽  
A.I. Gusri ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Tool Life ◽  
Flow Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Coolant Flow Rate ◽  
High Speed Machining ◽  
Dry Machining ◽  
Coated Cemented Carbide

The effectiveness of the usage of coolant in high speed machining of highly reactive material like titanium and its alloys is still far away uncertain. For this reason, it is wiser to study the effectiveness of MQL under transient cutting speed before we go to the high speed machining. This paper discusses the effect of MQL on the machinability of Ti-6Al-4V by using PVD coated cemented carbide tools. The machinability of Ti-6Al-4V was investigated based on the effect on cutting force and the tool life. The performance of PVD coated cemented carbide tool was investigated at various cutting condition. Completely dry machining and near dry (MQL) were applied in this experiment. For near dry machining, two levels of coolant flow rate were investigated, 50 and 100 mL/H. The effectiveness of mist coolant was tested at three different levels of cutting speed, 120, 135 and 150 m/min. Application of mist coolant is more significant at cutting speed of 135 m/min. At this speed longer tool life was obtained when more coolant was applied. No significant effect of the cutting speed and coolant flow rate on the surface roughness. Surface roughness is more sensitive to the feed rate and the depth of cut. No significant effect of application of MQL on cutting force at early stage of machining. MQL seems to be more affective when tools start worn out where greater contact area between tool and work piece occur to give better lubrication effect.

Multi-Objective Optimization Using Box-Behken of Response Surface Methodology for High-Speed Machining of Inconel 718

2014 ◽  
Vol 629 ◽  
pp. 487-492 ◽  
Author(s):  
Mohd Shahir Kasim ◽  
Che Hassan Che Haron ◽  
Jaharah Abd Ghani ◽  
E. Mohamad ◽  
Raja Izamshah ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Cutting Force ◽  
Response Surface ◽  
Tool Life ◽  
Feed Rate ◽  
Inconel 718 ◽  
High Speed ◽  
Cutting Speed ◽  
High Speed Milling

This study was carried out to investigate how the high-speed milling of Inconel 718 using ball nose end mill could enhance the productivity and quality of the finish parts. The experimental work was carried out through Response Surface Methodology via Box-Behnken design. The effect of prominent milling parameters, namely cutting speed, feed rate, depth of cut (DOC), and width of cut (WOC) were studied to evaluate their effects on tool life, surface roughness and cutting force. In this study, the cutting speed, feed rate, DOC, and WOC were in the range of 100 - 140 m/min, 0.1 - 0.2 mm/tooth, 0.5 - 1.0 mm and 0.2 - 1.8 mm, respectively. In order to reduce the effect of heat generated during the high speed milling operation, minimum quantity lubrication of 50 ml/hr was used. The effect of input factors on the responds was identified by mean of ANOVA. The response of tool life, surface roughness and cutting force together with calculated material removal rate were then simultaneously optimized and further described by perturbation graph. Interaction between WOC with other factors was found to be the most dominating factor of all responds. The optimum cutting parameter which obtained the longest tool life of 60 mins, minimum surface roughness of 0.262 μm and resultant force of 221 N was at cutting speed of 100 m/min, feed rate of 0.15 mm/tooth, DOC 0.5 m and WOC 0.66 mm.

Machining parameters effect in dry turning of AISI 316L stainless steel using coated carbide tools

2015 ◽  
Vol 231 (4) ◽  
pp. 676-683 ◽  
Author(s):  
Rusdi Nur ◽  
MY Noordin ◽  
S Izman ◽  
D Kurniawan
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Power Consumption ◽  
Cutting Force ◽  
Tool Life ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Machining Parameters ◽  
Aisi 316L ◽  
Coated Carbide

Austenitic stainless steel AISI 316L is used in many applications, including chemical industry, nuclear power plants, and medical devices, because of its high mechanical properties and corrosion resistance. Machinability study on the stainless steel is of interest. Toward sustainable manufacturing, this study also includes the power consumption during machining along with other machining responses of cutting force, surface roughness, and tool life. Turning on the stainless steel was performed using coated carbide tool without using cutting fluid. The turning was performed at various cutting speeds (90, 150, and 210 m/min) and feeds (0.10, 0.16, and 0.22 mm/rev). Response surface methodology was adopted in designing the experiments to quantify the effect of cutting speed and feed on the machining responses. It was found that cutting speed was proportional to power consumption and was inversely proportional to tool life, and showed no significant effect on the cutting force and the surface roughness. Feed was proportional to cutting force, power consumption, and surface roughness and was inversely proportional to tool life. Empirical equations developed from the results for all machining responses were shown to be useful in determining the optimum cutting parameters range.

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

scholarly journals Analysis and prediction of the impact of technological parameters on cutting force components in rough milling of AZ31 magnesium alloy

2021 ◽  
Vol 22 (1) ◽  
Author(s):  
M. Kulisz ◽  
I. Zagórski ◽  
A. Weremczuk ◽  
R. Rusinek ◽  
J. Korpysa
Keyword(s):  
Neural Networks ◽  
Magnesium Alloy ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Speed ◽  
Az31 Magnesium Alloy ◽  
High Speed Machining ◽  
Stability Lobe Diagram ◽  
Machining Conditions ◽  
Stability Lobe

AbstractThis paper presents the results of experimental study of the AZ31 magnesium alloy milling process. Dry milling was carried out under high-speed machining conditions. First, a stability lobe diagram was determined using CutPro software. Next, experimental studies were carried out to verify the stability lobe diagram. The tests were carried out for different feed per tooth and cutting speed values using two types of tools. During the experimental investigations, cutting forces in three directions were recorded. The obtained time series were subjected to general analysis and analysis using composite multiscale entropy. Modelling and prediction were performed using Statistica Neural Network software, in which two types of neural networks were applied: multi-layered perceptron and radial basis function. It was observed that milling with high cutting speed values allows for component values of cutting force to be lowered as a result of the transition into the high-speed machining conditions range. In most cases, the highest values for the analysed parameters were recorded for the component Fx, whereas the lowest were recorded for Fy. Additionally, the paper shows that a prediction (with the use of artificial neural networks) of the components of cutting force can be made, both for the amplitudes of components of cutting force Famp and for root mean square Frms.

scholarly journals Precision Hard Turning of Ti6Al4V Using Polycrystalline Diamond Inserts: Surface Quality, Cutting Temperature and Productivity in Conventional and High-Speed Machining

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5677
Author(s):  
Elshaimaa Abdelnasser ◽  
Azza Barakat ◽  
Samar Elsanabary ◽  
Ahmed Nassef ◽  
Ahmed Elkaseer
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Polycrystalline Diamond ◽  
Depth Of Cut ◽  
High Speed Machining ◽  
Conventional Machining

This article presents the results of an experimental investigation into the machinability of Ti6Al4V alloy during hard turning, including both conventional and high-speed machining, using polycrystalline diamond (PCD) inserts. A central composite design of experiment procedure was followed to examine the effects of variable process parameters; feed rate, cutting speed and depth of cut (each at five levels) and their interaction effects on surface roughness and cutting temperature as process responses. The results revealed that cutting temperature increased with increasing cutting speed and decreasing feed rate in both conventional and high-speed machining. It was found that high-speed machining showed an average increase in cutting temperature of 65% compared with conventional machining. Nevertheless, high-speed machining showed better performance in terms of lower surface roughness despite using higher feed rates compared to conventional machining. High-speed machining of Ti6Al4V showed an improvement in surface roughness of 11% compared with conventional machining, with a 207% increase in metal removal rate (MRR) which offered the opportunity to increase productivity. Finally, an inverse relationship was verified between generated cutting temperature and surface roughness. This was attributed mainly to the high cutting temperature generated, softening, and decreasing strength of the material in the vicinity of the cutting zone which in turn enabled smoother machining and reduced surface roughness.

Experimental Study on High Speed Machining of a Titanium Alloy

2009 ◽  
Vol 69-70 ◽  
pp. 451-455
Author(s):  
Guo Sheng Geng ◽  
Jiu Hua Xu
Keyword(s):  
Titanium Alloy ◽  
Tool Life ◽  
Surface Integrity ◽  
High Speed ◽  
Cutting Speed ◽  
Fatigue Property ◽  
High Speed Machining ◽  
Ta15 Titanium Alloy ◽  
Milling Tool ◽  
Speed Range

High Speed Machining (HSM) has been proved to be useful in the machining of many materials. This research is concerned with the performance of HSM in the milling of Ti-6.5Al-2Zr-1Mo-1V (TA15) titanium alloy. The tool life and wear mechanism of the milling tool under different cutting speed were investigated, and the influences of cutting speed on the surface integrity and fatigue property of the machined part were studied. According to the experimental results, acceptable tool life can be obtained in a speed range up to 200m/min. The results also show that increasing cutting speed can help to improve the surface integrity and fatigue property of the machined part.

An Experimental Study on Finish Dry Milling of AISI 321 Stainless Steel

2016 ◽  
Vol 861 ◽  
pp. 26-31 ◽  
Author(s):  
Peng Guo ◽  
Chuan Zhen Huang ◽  
Bin Zou ◽  
Jun Wang ◽  
Han Lian Liu ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Tool Wear ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Milling ◽  
Aisi 321 ◽  
Coated Cemented Carbide

The milling of AISI 321 stainless steel which has wide engineering applications particularly in automobile, aerospace and medicine is of great importance especially in the conditions where high surface quality is required. In this paper, L16 orthogonal array design of experiments was adopted to evaluate the machinability of AISI 321 stainless steel with coated cemented carbide tools under finish dry milling conditions, and the influence of cutting speed ( V ), feed rate ( f ) and depth of cut ( ap ) on cutting force, surface roughness and tool wear was analysed. The experimental results revealed that the cutting force decreased with an increase in the cutting speed and increased with an increase in the feed rate or the depth of cut. The tool wear was affected significantly by the cutting speed and the depth of cut, while the effect of the feed rate on the tool wear was insignificant. With the cutting speed increased up to 160 m/min, a decreasing tendency in the surface roughness was observed, but when the cutting speed was further increased, the surface roughness increased. The effect of the feed rate and the depth of cut on the surface roughness was slight.

Study of High-Speed Machining Parameters on Nickel-Based Alloy GH2132

2011 ◽  
Vol 189-193 ◽  
pp. 3142-3147 ◽  
Author(s):  
Dong Qiang Gao ◽  
Zhong Yan Li ◽  
Zhi Yun Mao
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Speed ◽  
Main Tool ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
High Speed Machining ◽  
Nickel Based Alloy

A model of stress and temperature field is established on nickel-based alloy cutting by finite element modeling and dynamic numerical simulating, and then combining high-speed machining test and orthogonality analysis method, the influence law of cutting parameters on the cutting force and tool wear has been researched, and the tool life and cutting force prediction model based on cutting parameters has been obtained. Finally, by genetic algorithm method cutting parameters are selected reasonably and optimized. The result shows that the bonding wear is main tool wear, and the influence of cutting speed on cutting force is smaller than feed per tooth and axial depth of cut.

Prediction of Surface Roughness in High Speed Machining of Inconel 718

2011 ◽  
Vol 264-265 ◽  
pp. 1193-1198
Author(s):  
Mokhtar Suhaily ◽  
A.K.M. Nurul Amin ◽  
Anayet Ullah Patwari
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Inconel 718 ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
High Speed Machining

Surface finish and dimensional accuracy is one of the most important requirements in machining process. Inconel 718 has been widely used in the aerospace industries. High speed machining (HSM) is capable of producing parts that require little or no grinding/lapping operations within the required machining tolerances. In this study small diameter tools are used to achieve high rpm to facilitate the application of low values of feed and depths of cut to investigate better surface finish in high speed machining of Inconel 718. This paper describes mathematically the effect of cutting parameters on Surface roughness in high speed end milling of Inconel 718. The mathematical model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using design of experiments and the response surface methodology (RSM). Central composite design was employed in developing the surface roughness models in relation to primary cutting parameters. Machining were performed using CNC Vertical Machining Center (VMC) with a HES510 high speed machining attachment in which using a 4mm solid carbide fluted flat end mill tool. Wyko NT1100 optical profiler was used to measure the definite machined surface for obtaining the surface roughness data. The predicted results are in good agreement with the experimental one and hence the model can be efficiently used to predict the surface roughness value with in the specified cutting conditions limit.

Sign in / Sign up

Export Citation Format

Share Document