Simulation and Experiment on the Residual Stress in Super-High Speed Grinding

2010 ◽  
Vol 135 ◽  
pp. 238-242
Author(s):  
Yue Ming Liu ◽  
Ya Dong Gong ◽  
Wei Ding ◽  
Ting Chao Han
Keyword(s):  
Residual Stress ◽  
High Speed ◽  
Element Model ◽  
Residual Stress Distribution ◽  
X Ray Diffraction ◽  
Machined Surface ◽  
X Ray ◽  
High Speed Grinding ◽  
Simulation And Experiment ◽  
Cylindrical Workpiece

In this paper, effective finite element model have been developed to simulation the plastic deformation cutting in the process for a single particle via the software of ABAQUS, observing the residual stress distribution in the machined surface, the experiment of grinding cylindrical workpiece has been brought in the test of super-high speed grinding, researching the residual stress under the machined surface by the method of X-ray diffraction, which can explore the different stresses from different super-high speed in actual, and help to analyze the means of reducing the residual stresses in theory.

Measurement of Residual Stress Distribution of Ground Silicon Nitride by Glancing Incidence X-ray Diffraction Technique

1995 ◽  
Vol 39 ◽  
pp. 331-338
Author(s):  
Yoshihisa Sakaida ◽  
Keisuke Tanaka ◽  
Shintaro Harada
Keyword(s):  
Residual Stress ◽  
Surface Layer ◽  
Stress Distribution ◽  
Stress Measurement ◽  
Scintillation Counter ◽  
Ground Surface ◽  
Residual Stress Distribution ◽  
X Ray Diffraction ◽  
X Ray ◽  
Very High

A new method of X-ray stress measurement was proposed to estimate non-destructively the steep residual stress distribution in the surface layer of ground Si3N4. We assumed an exponential decrement of the residual stress near the ground surface, and derived a formula for the lattice strain as a function of sin2Ψ. In the experiments, the diffraction angles were measured on the ground surface for a widest possible range of sin2ѱ using an Ω-goniometer. In order to measure the diffraction angle at very high sin η values, a scintillation counter was located on the -η side and an incident X-ray beam impinged on the ground surface with a very low angle from the +η side using the glancing incidence X-ray diffraction technique. A strong non-linearity was found in the 20-sin2ѱ diagrams especially at very high ѱ -angles. From the analysis of non-linearity, the stress distribution in the surface layer was determined. Tine residual stress took the maximum compression of 2 GPa at a depth of about 0.5 μm from the surface, and then diminished to zero at about 25 μm in depth. In the close vicinity of the ground surface, the compressive residual stress was relieved because of both the surface roughness and microcracking induced during the grinding process.

X-ray diffraction at constant penetration depth – a viable approach for characterizing steep residual stress gradients

2008 ◽  
Vol 41 (2) ◽  
pp. 377-385 ◽  
Author(s):  
Thomas Erbacher ◽  
Alexander Wanner ◽  
Tilmann Beck ◽  
Otmar Vöhringer
Keyword(s):  
Residual Stress ◽  
Penetration Depth ◽  
Ground Surface ◽  
Shear Stresses ◽  
X Rays ◽  
X Ray Diffraction ◽  
Machined Surface ◽  
Near Surface ◽  
X Ray ◽  
Surface Residual Stresses

The experimental analysis of near-surface residual stresses by X-ray diffraction methods is based on measuring the spacings of lattice planes while the inclination ψ with respect to the surface plane is changed stepwise. A characteristic feature of conventional techniques is that the penetration depth of the X-rays is altered as inclination is varied. By simultaneously varying three different goniometer angles in a particular fashion, both the penetration depth and the measuring direction can be held constant while ψ is varied. Thus the normal and shear stresses can be derived from the sin2ψ plots by means of standard evaluation procedures developed for gradient-free stress states. The depth profile of residual stress is then obtainedviaLaplace transformation of the results from several stress measurements carried out at different penetration depths. In the present paper, the feasibility of this experimental approach for characterizing the strongly graded, non-equiaxed stress state existing at a machined surface is demonstrated. The results from constant-penetration-depth measurements on the ground surface of an engineering ceramic are compared with those from conventional sin2ψ measurements.

Analysis on Residual Stress in TiN Coating with Different Thicknesses

2012 ◽  
Vol 217-219 ◽  
pp. 1306-1311
Author(s):  
Chuan Liang Cao ◽  
Xiang Lin Zhang ◽  
Hai Yang Wang
Keyword(s):  
Residual Stress ◽  
High Speed ◽  
Crystal Surface ◽  
Phase Variation ◽  
High Speed Steel ◽  
X Ray Diffraction ◽  
Tin Coating ◽  
X Ray ◽  
Hardness Tester ◽  
Tin Coatings

TiN coating is often coated on fine blanking tools made of with the powder metallurgy high speed steel S790 by Multi-arc ion plating. The phase variation, residual stress and microhardness of TiN coatings were respectively analyzed by X-Ray Diffraction(XRD) and Vickers hardness tester in this research. The result shows that: there is obvious preferred orientation in the crystal surface (1 1 1) and (2 2 2) of TiN coating, the residual stress of TiN coating ranges from -2 347 MPa to -1 920 MPa, and that of the substrate from -154.9 MPa to -69.21 MPa, both of which decrease with the increasing of coating thickness. The TiN coating on the S790 substrate was annealed at temperature 500°C for one hour. It was revealed that the stress state of TiN coating was better and thus the properties of the TiN coating were improved.

Residual Stresses in Butt Welding of Two Circular Pipes: An Experimental and Numerical Investigation

2014 ◽  
Author(s):  
Gurinder Singh Brar
Keyword(s):  
Finite Element Method ◽  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Welding Process ◽  
Diffraction Method ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray

Welding is a reliable and efficient joining process in which the coalescence of metals is achieved by fusion. Welding is carried out with a very complex thermal cycle which results in irreversible elastic-plastic deformation and residual stresses in and around fusion zone and heat affected zone (HAZ). A residual stress due to welding arises from the differential heating of the plates due to the weld heat source. Residual stresses may be an advantage or disadvantage in structural components depending on their nature and magnitude. The beneficial effect of these compressive stresses have been widely used in industry as these are believed to increase fatigue strength of the component and reduce stress corrosion cracking and brittle fracture. But due to the presence of residual stresses in and around the weld zone the strength and life of the component is also reduced. To understand the behavior of residual stresses, two 10 mm thick Fe410WC mild steel plates are butt welded using the Metal Active Gas (MAG) process. An experimental method (X-ray diffraction) and numerical analysis (finite element analysis) were then carried out to calculate the residual stress values in the welded plates. Three types of V-butt weld joint — two-pass, three-pass and four-pass were considered in this study. In multi-pass welding operation the residual stress pattern developed in the material changes with each weld pass. In X-ray diffraction method, the residual stresses were derived from the elastic strain measurements using a Young’s modulus value of 210 GPa and Poisson’s ratio of 0.3. Finite element method based, SolidWorks software was used to develop coupled thermal-mechanical three dimension finite element model. The finite element model was evaluated for the transient temperatures and residual stresses during welding. Also variations of the physical and mechanical properties of material with the temperature were taken into account. The numerical results for peak transverse residual stresses attained in the welded plates for two-pass, three-pass and four-pass welded joint were 67.7 N/mm2, 58.6 N/mm2, and 48.1 N/mm2 respectively. The peak temperature attained during welding process comes out to be 970°C for two-pass weld, 820.8°C for three-pass weld and 651.9°C for four-pass weld. It can be concluded that due to increase in the number of passes during welding process or deposition weld beads, the residual stresses and temperature distribution decrease. Also, the results obtained by finite element method agree well with those from experimental X-ray diffraction method.

Residual Stress Measurements in Multi-Pass Welded High Strength Steel Using Energy Dispersive Synchrotron X-Ray Diffraction

2014 ◽  
Vol 922 ◽  
pp. 177-182
Author(s):  
H. Gao ◽  
R.M. Huizenga ◽  
R.K. Dutta ◽  
M. Amirthalingam ◽  
M.J.M. Hermans ◽  
...  
Keyword(s):  
Residual Stress ◽  
High Strength ◽  
Depth Resolution ◽  
Element Model ◽  
Energy Dispersive ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Tensile Stresses ◽  
Transverse Tensile

Six pass welds were made on a 16 mm thick high strength quenched and tempered structural steel plate (S690QL1, Fe-0.16C-0.2Si-0.87Mn-0.33Cr-0.21Mo (wt.%)). Depth resolved measurements in two orthogonal directions were carried out using energy dispersive synchrotron X-ray diffraction at the ID15 beamline of the European Synchrotron Radiation Facility. The strains were calculated from the shift in the local d-spacing for four bcc planes ({200}, {211}, {220}, {310}). The planar stresses were calculated from the biaxial Hooke’s law, using the diffraction elastic constants of the individual planes. A two dimensional cross-sectional residual stress map with a depth resolution of 2 mm was obtained. Transverse compressive stresses were found at the weld toes and root. Transverse tensile stresses were present in the middle of the plate. Longitudinal tensile stresses concentrated along the fusion line. This work describes the procedures to obtain the depth resolved residual stress map and the generated results provide necessary information to validate thermal mechanical finite element model of multi-pass welding.

Sign in / Sign up

Export Citation Format

Share Document