Effects of Heat Treatment on some Physical Properties of Douglas Fir (Pseudotsuga Menziesii) Wood

2011 ◽  
Vol 197-198 ◽  
pp. 90-95 ◽  
Author(s):  
Xian Jun Li ◽  
Zhi Yong Cai ◽  
Qun Ying Mou ◽  
Yi Qiang Wu ◽  
Yuan Liu
Keyword(s):  
Heat Treatment ◽  
Physical Properties ◽  
Pseudotsuga Menziesii ◽  
Treatment Time ◽  
Treated Wood ◽  
Untreated Wood ◽  
Douglas Fir ◽  
Treatment Temperature ◽  
Color Changes ◽  
Moisture Performance

In this study the effect of heat treatment on some physical properties of Douglas fir (Pseudotsuga menziesii) was investigated. Wood specimens were subjected to heat treatment at 160, 180, 200 and 220°C for 1, 2, 3 and 4h. The results show that heat treatment resulted in a darkened color, decreased moisture performance and increased dimensional stability of wood. Compared with untreated wood, equilibrium moisture content (EMC), water absorption (WA) and volume swelling (VS) for treated wood decrease up to 42.63%, 34.93% and 67.47%. The higher the treatment temperature and the longer the treatment time, the lower EMC, WA and VS. The VS of treated specimens has a more significant reduction than EMC and WA when the heat treatment temperature is above 180°C. The visual color changes were more distinct after heat treatment above 180°C. Temperature has a greater influence than time on these properties of specimens.

Effect of High Temperature on the Change in Color, Dimensional Stability and Mechanical Properties of Spruce Wood

Holzforschung ◽  
2003 ◽  
Vol 57 (5) ◽  
pp. 539-546 ◽  
Author(s):  
P. Bekhta ◽  
P. Niemz
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Temperature ◽  
Dimensional Stability ◽  
Modulus Of Elasticity ◽  
Bending Strength ◽  
Treatment Time ◽  
Color Difference ◽  
Treatment Temperature ◽  
Color Changes

Summary In this study the effect of high temperature on mechanical properties, dimensional stability and color of spruce was investigated. Wood specimens conditioned at different relative humidities (50, 65, 80 and 95%) were subjected to heat treatment at 200°C for 2, 4, 8, 10 and 24 h and at 100, 150 and 200°C for 24 h. Color changes were measured in the Minolta Croma-Meter CR-300 color system. Bending strength and modulus of elasticity were determined according to DIN 52186. The results show that heat treatment mainly resulted in a darkening of wood tissues, improvement of the dimensional stability of wood and reduction of its mechanical properties. The darkening accelerated generally when treatment temperature exceeded approximately 200°C. Most of the darkening occurred within the first 4 h of exposure. For the specimens heated to high temperatures, the average decrease in bending strength was about 44–50%, while modulus of elasticity was reduced by only 4–9%. We found that treatment time and temperature were more important than relative humidity regarding the color responses. Strong correlations between total color difference and both modulus of elasticity and bending strength were found. Thus, the color parameters can be estimated quantitatively and used as a prediction of wood strength.

Effect of Heat Treatment Temperature on the Color of Okan Wood

2011 ◽  
Vol 214 ◽  
pp. 531-534 ◽  
Author(s):  
Qiang Shi ◽  
Fu Cheng Bao ◽  
Jian Xiong Lu ◽  
Jing Hui Jiang
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Color Change ◽  
Treated Wood ◽  
Color Difference ◽  
Treatment Temperature ◽  
Strong Correlations ◽  
Color Changes ◽  
Color System ◽  
Effect Of Treatment

In this study the effect of high temperature on color change of okan wood was investigated. Wood specimens were subjected to heat treatment at 160°C, 180°C,200°C,220°Cfor 4 hours with the superheated steam as a heating medium and a shielding gas. Color changes were measured in the Minolta Croma-Meter CR-300 color system. The color parameters L*, a*, b* were determined by the CIEL*a*b* method on the surface of untreated and treated wood, and their variation with regard to the treatment (△L*,△a*,△b* ) were calculated. It was found that heat treatment resulted in a darkening of wood tissues, Color became dark with the temperature increases. The darkening accelerated when treatment temperature exceeded approximately 200°C. We found that heat treatment temperature were substantially important regarding the color responses. Strong correlations between total color difference and the treatment temperature were found. The effect of treatment temperature on color change in sapwood is more obvious than that in heartwood, the color of sapwood and heartwood tended to be more uniform when the temperature reaches more than 200°C.

Comparison of the color and weight change in Paulownia tomentosa and Pinus koraiensis wood heat-treated in hot oil and hot air

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5574-5585
Author(s):  
Intan Fajar Suri ◽  
Jong Ho Kim ◽  
Byantara Darsan Purusatama ◽  
Go Un Yang ◽  
Denni Prasetia ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Color Change ◽  
Treated Wood ◽  
Pinus Koraiensis ◽  
Weight Changes ◽  
Paulownia Tomentosa ◽  
Wood Color ◽  
Color Changes ◽  
Hot Air ◽  
Heat Treated

Color changes were tested and compared for heat-treated Paulownia tomentosa and Pinus koraiensis wood treated with hot oil or hot air for further utilization of these species. Hot oil and hot air treatments were conducted at 180, 200, and 220 °C for 1, 2, and 3 h. Heat-treated wood color changes were determined using the CIE-Lab color system. Weight changes of the wood before and after heat treatment were also determined. The weight of the oil heat-treated wood increased considerably but it decreased in air heat-treated wood. The oil heat-treated samples showed a greater decrease in lightness (L*) than air heat-treated samples. A significant change in L* was observed in Paulownia tomentosa. The red/green chromaticity (a*) of both wood samples increased at 180 and 200 °C and slightly decreased at 220 °C. The yellow/blue chromaticity (b*) in both wood samples increased at 180 °C, but it rapidly decreased with increasing treatment durations at 200 and 220 °C. The overall color change (ΔE*) in both heat treatments increased with increasing temperature, being higher in Paulownia tomentosa than in Pinus koraiensis. In conclusion, oil heat treatment reduced treatment duration and was a more effective method than air heat treatment in improving wood color.

Characteristics of Lithium Polysilicate Electrolyte Synthesized by Sol-Gel Processing

2007 ◽  
Vol 124-126 ◽  
pp. 1031-1034
Author(s):  
Bong Soo Jin ◽  
Bok Ki Min ◽  
Chil Hoon Doh
Keyword(s):  
Heat Treatment ◽  
Acid Treatment ◽  
Treatment Time ◽  
Sol Gel ◽  
Silicate Solution ◽  
Treatment Temperature ◽  
Lithium Silicate ◽  
Treatment Conditions ◽  
Xrd Patterns ◽  
Si Wafer

To find out suitable Si surface treatment and heat treatment conditions, acid treatment of Si wafer was done for lithium polysilicate electrolyte coating on Si wafer. In case of HCl treatment, the wet angle of a sample is 30o, which is the smallest wet angle of other acid in this experiment. Acid treatment time is 10 min, which is no more change of wet angle. Lithium polysilicate electrolyte was synthesized by hydrolysis and condensation of lithium silicate solution using perchloric acid. Thermal analysis of lithium polysilicate electrolyte shows the weight loss of ~23 % between 400 and 500 , which is due to the decomposition of LiClO4. The XRD patterns of the obtained lithium polysilicate electrolyte also show the decrement of LiClO4 peak at 400 . The optimum heat treatment temperature is below 400 , which is the suitable answer for lithium polysilicate electrolyte.

Laccase-catalyzed functionalization with 4-hydroxy-3-methoxybenzylurea significantly improves internal bond of particle boards

Holzforschung ◽  
2008 ◽  
Vol 62 (2) ◽  
pp. 223-229 ◽  
Author(s):  
Karin Fackler ◽  
Thomas Kuncinger ◽  
Thomas Ters ◽  
Ewald Srebotnik
Keyword(s):  
Internal Bond ◽  
Treatment Time ◽  
Urea Formaldehyde ◽  
Treated Wood ◽  
Untreated Wood ◽  
Strength Properties ◽  
Positive Interactions ◽  
Formaldehyde Resin ◽  
Significant Difference ◽  
Wood Particles

Abstract Enzymatic functionalization is an attractive tool to provide a reactive interface for further processing of lignocellulosic materials, such as wood particles and fibers. Here, spruce wood particles have been functionalized by fungal laccase combined with 4-hydroxy-3-methoxy-benzylamine (HMBA) or 4-hydroxy-3-methoxybenzylurea (HMBU). The expectation was crosslinking with resins in subsequent glueing processes, which should improve strength properties of particle boards. Essential process parameters, such as liquid to solid mass ratio and treatment time, were optimized on a laboratory scale resulting in HMBA and HMBU binding yields of 90% and above as determined by radiochemical mass balance analysis. We employed a multifactorial experimental design for board production from treated wood particles and urea/formaldehyde resin. Mechanical testing and multivariate data analysis revealed, for the first time, an increase of internal bond (IB) as a result of functionalization with HMBU. HMBA was not successful. Variance analysis of relevant parameters and their interactions demonstrated a highly significant difference (P>99.99%) between boards treated with laccase/HMBU versus untreated wood particles. Due to positive interactions, functionalization was most effective at high bulk density (750 kg m-3) and high resin content (10%) resulting in a calculated IB improvement of 0.12 N m-2 (21%).

scholarly journals COLOR CHANGE — MASS LOSS CORRELATION FOR HEAT-TREATED WOOD

2014 ◽  
Vol 2 ◽  
pp. 345-352 ◽  
Author(s):  
Cristina Marinela Olarescu ◽  
Mihaela Campean
Keyword(s):  
Heat Treatment ◽  
Mass Loss ◽  
Color Change ◽  
Treated Wood ◽  
Untreated Wood ◽  
Cost Effective ◽  
Assessment Procedure ◽  
Mathematical Correlation ◽  
Heat Treated ◽  
Two Parameters

Heat treatment is renowned as the most environmentally friendly process of dimensional stabilization that can be applied to wood, in order to make it suitable for outdoor uses. It also darkens wood color and improves wood durability. The intensity of heat treatment can be appreciated by means of two parameters: the color change occured in wood due to the high temperature, and the mass loss, which is a measure of the degree of thermal degradation. In order to find a mathematical correlation between these two parameters, an experimental study was conducted with four European wood species, which were heat-treated at 180°C and 200ºC, for 1-3 hours, under atmosheric pressure.The paper presents the results concerning the color changes and mass losses recorded for the heat-treated wood samples compared to untreated wood.  For all four species, the dependency between the color change and the mass loss was found to be best described by a logarithmic regression equation with R2 of 0.93 to 0.99 for the soft species (spruce, pine and lime), and R2 of 0.77 for beech. The results of this study envisage to simplify the assessment procedure of the heat treatment efficiency, by only measuring the color – a feature that is both convenient and cost-effective. 

Low-temperature thermal pretreatment process for recycling inner core of spent lithium iron phosphate batteries

2020 ◽  
pp. 0734242X2095740
Author(s):  
Haijun Bi ◽  
Huabing Zhu ◽  
Lei Zu ◽  
Yong Gao ◽  
Song Gao ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Low Temperature ◽  
Heat Treatment Temperature ◽  
Lithium Iron Phosphate ◽  
Inner Core ◽  
Treatment Time ◽  
Iron Phosphate ◽  
Treatment Temperature ◽  
Heat Treatment Time ◽  
Physicochemical Changes

Spent lithium iron phosphate (LFP) batteries contain abundant strategic lithium resources and are thus considered attractive secondary lithium sources. However, these batteries may contaminate the environment because they contain hazardous materials. In this work, a novel process involving low-temperature heat treatment is used as an alternative pretreatment method for recycling spent LFP batteries. When the temperature reaches 300°C, the dissociation effect of the anode material gradually improves with heat treatment time. At the heat treatment time of 120 minutes, an electrode material can be dissociated. The extension of heat treatment time has a minimal effect on quality loss. The physicochemical changes in thermally treated solid cathode and anode materials are examined through scanning electron microscopy with energy-dispersive X-ray spectroscopy. The heat treatment results in the complete separation of the materials from aluminium foil without contamination. The change in heat treatment temperature has a small effect on the quality of LFP material shedding. When the heat treatment temperature reaches 300°C and the time reaches 120 minutes, heat treatment time increases, and the yield of each particle size is stable and basically unchanged. The method can be scaled up and may reduce environmental pollution due to waste LFP batteries.

Microstructure of Semi-Solid Extruded Copper Alloy after Heat Treatment

2019 ◽  
Vol 285 ◽  
pp. 146-152
Author(s):  
Nai Yong Li ◽  
Han Xiao ◽  
Chi Xiong ◽  
De Hong Lu ◽  
Rong Feng Zhou
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Copper Alloy ◽  
Treatment Time ◽  
Solid Phase ◽  
Treatment Temperature ◽  
Primary Phase ◽  
Holding Time ◽  
Average Grain Size ◽  
Semi Solid

The semi-solid extruded ZCuSn10P1 copper alloy were annealed at different temperatures and time. The influences of heat treatment temperature and holding time on the microstructure of semi-solid ZCuSn10P1 copper alloy were investigated. The results show that with the increase of heat treatment temperature, the morphology of the semi-solid microstructure was improved, the sharp angle around the primary phase α-Cu and the liquid droplets were reduced. With the increase of heat treatment time, the solid-liquid segregation of the semi-solid structure was improved. The average grain size of the solid phase increased with the increasing of the holding time. After heat treatment, the solid solubility of the primary phase α-Cu increased, and the Sn and P elements in the liquid phase continued to diffuse to the primary phase α-Cu. The microstructure of semi-solid copper alloy was the most uniform after heat treatment at 350°C for 120 min.

Effect of Heat Treatment on the Reactivity and Crystallinity of Coal-Char

2005 ◽  
Author(s):  
Shouyu Zhang ◽  
Junfu Lu ◽  
Jianmin Zhang ◽  
Qing Liu ◽  
Guangxi Yue
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Time ◽  
Treatment Temperature ◽  
Coal Char ◽  
Heat Treatment Time ◽  
Heat Treat ◽  
Heat Treated ◽  
Layer Stacking ◽  
Crystalline Growth

The effect of heat treatment on the reactivity and crystallinity of char prepared from the vitrinite of two coals (YX, JJ) was investigated by using XRD and TGA in this paper. The results from TGA show that the reactivity of the chars from YXV and JJV decreases with the increase of heat treatment temperature. The reactivity of YXV char decreases quickly and significantly as heat treatment time increases. However, after heat treatment time of 60 min, it decreases slowly. The effect of heat treatment time on the reactivity of JJV char is small. The results from XRD show that the crystallinity of coal-char is determined by the intensity of heat treatment. When heat treatment time is more than 60 minutes, the turbostratic crystallite of YXV char prepared under 900°C changes remarkably and becomes more orderly. The aromatic layer stacking heights (Lc) of YXV Char when heat treated above 900°C increased with the increase of heat treatment time. The effect of heat treat time on Lc of JJV char is small, but under heat treatment temperature of 1200°C, the crystalline of JJV char grows distinctly. There is a good parallel relationship between the crystalline growth and deactivation of the chars. It can be concluded that the growth of the crystalline is the main reason for the deactivation of coal-char.

scholarly journals Effects of aluminum sulfate soaking pretreatment on dimensional stability and thermostability of heat-treated wood

2020 ◽  
Author(s):  
Lijie Qu ◽  
Zhenyu Wang ◽  
Jing Qian ◽  
Zhengbin He ◽  
Songlin Yi
Keyword(s):  
Heat Treatment ◽  
Thermal Stability ◽  
Thermal Degradation ◽  
Structural Changes ◽  
Aluminum Sulfate ◽  
Treated Wood ◽  
Treatment Temperature ◽  
Chinese Fir ◽  
Heat Treated ◽  
Thermal Stability Of

Abstract Acidic aluminum sulfate hydrolysis solutions can be used to catalyze the thermal degradation of wood in a mild temperature environment, and thus reduce the temperature required for heat treatment process. To improve the dimensional and thermal stability of Chinese fir during heat treatment at 120 °C, 140 °C and 160 °C, this study investigated the effects of soaking pretreatment with 5%, 10% and 15% aluminum sulfate on the chemical and structural changes of the heat-treated Chinese fir. The results indicated that the samples treated at 15% aluminum sulfate concentration and 160 °C heat treatment achieved the best dimensional and thermal stability. Chemical analyses by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) indicated that the catalysis of aluminum sulfate resulted in degradation of hemicelluloses during the heat treatment, and an increase in the soaking concentration and heat treatment temperature also affected the thermal degradation of celluloses. The scanning electron microscope (SEM) and mass changes test results proved that the hydrolyzed aluminum flocs mainly adhered to the inner wall of the wood tracheid as spherical precipitates, and when the soaking concentration reached 10% and 15%, a uniform soaking effect could be achieved. The thermogravimetric (TG) analysis revealed the soaking pretreatment effectively improved the thermal stability of the heat-treated wood by physically wrapping and promoting the formation of a carbon layer on the wood surface during heat treatment. Thus, aluminum sulfate soaking pretreatment exerted a great effect on the dimensional and thermal stability of wood, allowing heat treatment to be performed at a lower temperature.

Sign in / Sign up

Export Citation Format

Share Document