Analysis and Simulation of the Shear Deformation for Woven Cloth

2011 ◽  
Vol 201-203 ◽  
pp. 203-208
Author(s):  
Liang Chen ◽  
Shu Guang Zhao ◽  
Li Juan Zhang ◽  
Li Qiang Zhang ◽  
Wen Bing Zhang
Keyword(s):  
Mechanical Properties ◽  
Shear Deformation ◽  
Mechanical Model ◽  
Shear Behavior ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Cloth Simulation ◽  
Specific Strength ◽  
High Specific Strength

Woven fabrics are used in a wide variety of products, and they are prized for their flexibility, formability, and high specific strength. However, modeling woven cloth is difficult due, in particular, to complex mechanical properties. In this paper, the shear behavior of plain woven fabric is studied. Through the analysis, a mechanical model is proposed which take the shearing properties into account. It uses physical-based model for animating cloth objects. Furthermore, we demonstrate the efficiency of this method with examples related to accurate cloth simulation from experimental shear curve measured on actual materials.

scholarly journals CARBON FIBRE ALIGNMENT FOR REINFORCED COMPOSITES USING EMBROIDERY TECHNOLOGY

2021 ◽  
Vol 2021 ◽  
pp. 102-108
Author(s):  
J. Domenech-Pastor ◽  
P. Diaz-Garcia ◽  
D. Garcia
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Carbon Fibre ◽  
Carbon Fibers ◽  
Vertical Direction ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Reinforced Composites ◽  
Good Opportunity ◽  
Fibre Reinforced Composites

Composites are materials formed by the combination of two or more components that acquire better properties than the ones obtained by each component on its own. Composites have been widely used in the industry due to its light weight and good mechanical properties. To improve these properties several layers of reinforced material (e.g., carbon fibre) are overlapped which produce an increase in the fibre consumption. In this sense Tailored Fibre Placement (TFP) embroidery can offer good opportunity to reduce the consumption of reinforced fibre while improving the mechanical properties due to the alignment of the fibres in the effort direction. This study analyzes the performance of carbon fibre reinforced composites with Polyester resin made with TFP embroidery technology against flexural strength efforts and without using plain woven fabrics to demonstrate that the use of reinforcement fabrics in composites can be optimized by a curved alignment of the fibers. Two different structures were embroidered with TFP technology, one simulating a woven fabric with straight unidirectional alignment of fibres in horizontal and vertical direction, and a second structure made with curvilinear alignment of carbon fibers. After the study of the flexural mechanical properties an improvement of 18% was obtained in maximum flexural strength.

Effect of Core Thickness and Intermediate Layers on Mechanical Properties of Polypropylene Honeycomb Multi-Layer Sandwich Structures

2014 ◽  
Vol 59 (1) ◽  
pp. 11-16 ◽  
Author(s):  
J. Arbaoui ◽  
Y. Schmitt ◽  
J.-L. Pierrot ◽  
F.-X. Royer
Keyword(s):  
Mechanical Properties ◽  
Sandwich Structures ◽  
Bending Test ◽  
Honeycomb Core ◽  
Lightweight Construction ◽  
Specific Strength ◽  
High Specific Strength ◽  
Intermediate Layers ◽  
Core Thickness ◽  
Strength And Stiffness

Abstract Sandwich structures are widely used in lightweight construction especially in aerospace industries because of their high specific strength and stiffness. This paper investigates the effect of core thickness and intermediate layers on the mechanical properties of a polypropylene honeycomb core/composite facing multilayer sandwich structure under three points bending. We developed a theoretical model which makes it possible to calculate the shear properties in multi-cores. The results obtained by this model are agreed with our experimental results, and the results obtained with bending test showed that the mechanical properties of the composite multilayer structures increase with core thickness and intermediate layers.

scholarly journals New Numerical Model of Composite Fabric Behaviour: Simulation of Manufacturing of thin Composite Part

2000 ◽  
Vol 9 (3) ◽  
pp. 096369350000900 ◽  
Author(s):  
J.L. Billoet ◽  
A. Cherouat
Keyword(s):  
Mechanical Properties ◽  
Tensile Tests ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Forming Process ◽  
Composite Part ◽  
Initial Shape ◽  
Shaping Process ◽  
Mechanical Approach ◽  
Behaviour Simulation

The present study concerns the modelling of the behaviour of pre-impregnated woven fabric during the forming process. The mechanical approach is based on a mesostructural model. It allows us to take into account the mechanical properties of fibres and resin and the various dominating mode of deformation of woven fabrics during the forming process. Shear and tensile tests of composite fabric specimens are proposed and compared with the experimental results in order to demonstrate the efficiency of our approach. Different numerical simulations and experiments of shaping process have been carried out in order to validate the proposed computational formulation. The various forming parameters examined have included the initial shape of fabric, fibre orientations and viscosity of resin.

A novel approach for precise determination of in-plane shear behavior of woven fabrics

2016 ◽  
Vol 87 (11) ◽  
pp. 1335-1348 ◽  
Author(s):  
Nazli Uren ◽  
Eren Oner ◽  
Ayse Okur
Keyword(s):  
Mechanical Properties ◽  
Correlation Coefficients ◽  
Shear Behavior ◽  
Precise Determination ◽  
Woven Fabrics ◽  
Raw Material ◽  
Bending Rigidity ◽  
Plane Shear ◽  
Novel Approach ◽  
Shear Frame

The ability of a textile product to change shape under motion-based diagonal forces defines the shear behavior of a fabric and its suitability for a wearable garment design. The principal aim of this study is to introduce a new shear frame and investigate the effects of raw material and setting on in-plane shear behavior of woven fabrics. For this purpose, the mechanical properties of systematic and commercially available non-systematic fabrics were measured. A novel approach to determine the in-plane shear behavior of woven fabrics via two complementary shear frame measurements was presented. The results were also compared with a conventional method known as the bias extension method. It was established that the proposed method provides more accurate and precise results. In order to investigate the correlation between in-plane shear behavior and other mechanical properties, bending rigidity and extension ability of fabrics were measured as well. The analyses regarding the relations between selected fabric parameters showed that there are considerably high correlation coefficients. The effect of raw material and setting was likewise found out to be statistically significant.

scholarly journals Microstructure and Mechanical Properties of Rapidly Solidified β-Type Ti–Fe–Sn–Mo Alloys with High Specific Strength and Low Elastic Modulus

Metals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 1135 ◽  
Author(s):  
Li ◽  
Ma ◽  
Jia ◽  
Meng ◽  
Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Volume Fraction ◽  
High Yield ◽  
Specific Strength ◽  
High Specific Strength ◽  
Microstructure And Mechanical Properties ◽  
Low Elastic Modulus ◽  
Mo Content ◽  
Rapidly Solidified

The microstructure and mechanical properties of rapidly solidified β-type Ti–Fe–Sn–Mo alloys with high specific strength and low elastic modulus were investigated. The results show that the phases of Ti–Fe–Sn–Mo alloys are composed of the β-Ti, α-Ti, and TiFe phases; the volume fraction of TiFe phase decreases with the increase of Mo content. The high Fe content results in the deposition of TiFe phase along the grain boundary of the Ti phase. The Ti75Fe19Sn5Mo1 alloy exhibits the high yield strength, maximum compressive strength, large plastic deformation, high specific strength, high Vickers hardness, and large toughness value, which is a superior new engineering material. The elastic modulus (42.1 GPa) of Ti75Fe15Sn5Mo5 alloy is very close to the elastic modulus of human bone (10–30 GPa), which indicating that the alloy can be used as a good biomedical alloy. In addition, the large H/Er and H3/Er2 values of Ti75Fe19Sn5Mo1 alloy indicate the good wear resistance and long service life as biomedical materials.

scholarly journals Numerical Tools for Composite Woven Fabric Preforming

2013 ◽  
Vol 2013 ◽  
pp. 1-18 ◽  
Author(s):  
Abel Cherouat ◽  
Houman Bourouchaki
Keyword(s):  
Mechanical Properties ◽  
Composite Structures ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Angular Distortion ◽  
Geometrical Approach ◽  
Forming Process ◽  
Manufacture Process ◽  
Mould Surface ◽  
Mechanical Approach

An important step in the manufacturing processes of thin composite components is the layingup of the reinforcement onto the mould surface. The prediction of the angular distortion of the reinforcement during draping and the changes in fibre orientation are essential for the understanding of the manufacture process and the evaluation of the mechanical properties of the composite structures. This paper presents an optimization-based method for the simulation of the forming processes of woven fabric reinforced composites. Two different approaches are proposed for the simulation of the draping of woven fabric onto complex geometries: geometrical and mechanical approaches. The geometrical approach is based on a fishnet model. It is well adapted to predimensioning fabrics and to give a suitable quantification of the resulting flat patterns. The mechanical approach is based on a mesostructural model. It allows us to take into account the mechanical properties of fibres and resin and the various dominating mode of deformation of woven fabrics during the forming process. Some numerical simulations of the forming process are proposed and compared with the experimental results in order to demonstrate the efficiency of our approaches.

Structural Optimization of Woven Fabric with Curved Surface

2012 ◽  
Vol 443-444 ◽  
pp. 408-411
Author(s):  
Yan Fang Wang ◽  
Xing Feng Guo
Keyword(s):  
Structural Optimization ◽  
Shear Deformation ◽  
Three Dimensional ◽  
Single Layer ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Curved Surface ◽  
Theoretical Formula ◽  
Curved Surfaces

The woven fabric with curved surfaces is a kind of single layer woven fabrics, which was produced to smoothly fit three-dimensional solids. The warp or weft of the winding fabric bend were normally made with different lengths, which may result in shear deformation in many cases and accordingly twisting the structure of the fabric after fitted onto the solid. In order to solve the problem mentioned above, a theoretical formula was used to calculate the optimal intervals of the pick-spacing and an improved structure thus was developed in this study.

Mechanical Properties of Al2O3 Reinforced Cast and Hot Extruded Al Based Metal Matrix Composites

2015 ◽  
Vol 813-814 ◽  
pp. 208-212
Author(s):  
S. Ghanaraja ◽  
K.L. Vinuth Kumar ◽  
K.S. Ravikumar ◽  
B.M. Madhusudan
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Base Alloy ◽  
High Strength ◽  
Matrix Composites ◽  
Specific Strength ◽  
Good Corrosion Resistance ◽  
High Specific Strength ◽  
Low Weight

The Synthesis of aluminium matrix composites is receiving considerable emphasis in meeting the requirements of various industries. Due to the desired properties such as low weight, high specific strength, good corrosion resistance and excellent wear resistance, they have received a great interest in the recent years. Metal-matrix composites (MMCs) based on aluminium and magnesium has emerged as an important class of materials and Al2O3can be considered as ideal reinforcements, due to their high strength, high aspect ratio and thermo-mechanical properties. The objective of this work is to reinforce Al 1100-Mg alloy with different wt% of Al2O3(0, 3, 6, 9 and 12) was added by melt stirring method and Extrusion is carried out (extrusion ratio of 12.25) for the same alloy and composites. Mechanical property like hardness and tensile properties have been investigated for cast and extruded of base alloy and composites.

Effect of warp and fill-fiber volume fractions on mechanical properties of glass/epoxy woven fabric composites

2020 ◽  
Vol 54 (24) ◽  
pp. 3501-3513
Author(s):  
Mohammad Aghaei ◽  
Mahmood M Shokrieh ◽  
Reza Mosalmani
Keyword(s):  
Mechanical Properties ◽  
Micromechanical Model ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Experimental Program ◽  
Fiber Volume ◽  
Volume Fractions ◽  
Woven Fabric Composites ◽  
New Concepts ◽  
Fabric Composites

Mechanical properties of woven fabric composites are influenced by fabric geometry and harness. In the present research, woven fabric composites made of ML-506 epoxy resin and E-glass woven fabrics with three different fabric geometries (harnesses of 2, 5, and 8) were studied experimentally. The new concepts of warp and fill-fiber volume fractions were introduced. Based on these new concepts, a micromechanical model for predicting the stiffness and strength of composites made of woven fabrics was developed. An experimental program was conducted to evaluate the present model and the new concepts of warp and fill-fiber volume fractions. The results obtained by the new micromechanical model have been compared with the conducted experimental results as well as the experimental data available in the literature, and very good correlations were obtained.

Sign in / Sign up

Export Citation Format

Share Document