Influencing Factors of the Fluidity and Strength of Phosphate Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 464-468
Author(s):  
Hong Tao Wang ◽  
Ju Hui Cao ◽  
Shuang Mei Li ◽  
Ming Xue
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Retention ◽  
Natural Conditions ◽  
Slump Flow ◽  
Influence Of Water ◽  
Binder Ratio ◽  
Curing Methods ◽  
Early Strength ◽  
Water Binder Ratio

The influence of water binder ratio, content of borax and fly ash on the fluidity and strength of phosphate concrete were investigated. Results showed that the slump and slump flow of phosphate concrete improved with content of water and borax increasing. But the strength decreased, especially early strength. While the mixing amount of borax was less than 1.5% of the magnesium phosphate cement, the influence on later strength was relatively less. The fluidity decreased significantly and the cohesiveness and water retention improved while the content of fly ash was between 10% and 30%.The compressive strength increased while the content of fly ash was 10%.The better curing methods was curing in the natural conditions, the compressive increased with the age prolonged.

Experimental Study on Workability and Strength of Green High Performance Concrete with High Volume Fly Ash

2013 ◽  
Vol 859 ◽  
pp. 52-55 ◽  
Author(s):  
Yong Qiang Ma
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
High Performance ◽  
High Performance Concrete ◽  
High Volume ◽  
Ash Content ◽  
Splitting Tensile Strength ◽  
Binder Ratio ◽  
Water Binder Ratio

A great deal of experiments have been carried out in this study to reveal the effect of the water-binder ratio and fly ash content on the workability and strengths of GHPC (green high performance concrete). The workability of GHPC was evaluated by slump and slump flow. The strengths include compressive strength and splitting tensile strength. The results indicate that the increase of water-binder ratio can improve the workability of GHPC, however the strengths of GHPC were decreased with the increase of water-binder ratio. When the fly ash content is lower than 40%, the increase in fly ash content has positive effect on workability of GHPC, while the workability begins to decrease after the fly ash content is more than 40%. The addition of fly ash in GHPC has adverse effect on the strengths, and there is a tendency of decrease in the compressive strength and splitting tensile strength of GHPC with the increase of fly ash content.

scholarly journals Early Strength Development of Soft Clay Stabilized by One-Part Ground Granulated Blast Furnace Slag and Fly Ash-Based Geopolymer

2021 ◽  
Vol 8 ◽  
Author(s):  
Xiyao Zheng ◽  
Jun Wu
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Soft Clay ◽  
Strength Development ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Early Strength ◽  
Furnace Slag ◽  
Water Binder Ratio

One-part or “just add water” geopolymer is a cementitious material, which is friendly to environment and users in applications. However, the mechanical behavior of the soft soil stabilized by one-part geopolymer is not well acknowledged. In this study, soft clay was stabilized with ground granulated blast furnace slag (GGBFS) and fly ash (FA)-based geopolymer, which is a mixture of solid aluminosilicate precursor (Al-Si raw materials: GGBFS and FA), solid alkali activator, and water. The objective was to adopt one-part geopolymer as an alternative soil binder to completely replace ordinary Portland cement (OPC) for stabilizing the soft clay and evaluate the effect of the factors (i.e., GBFS/FA ratio in Al-Si precursor, activator/Al-Si precursor ratio, and water/binder ratio) that influenced the early strength. Results showed that the increase of the FA content in the Al-Si precursor increased the unconfined compressive strength (UCS) values significantly through the geopolymerization process. The highest UCS values were achieved with 90% GGBFS to 10% FA in the precursor when the activator/precursor and water/binder ratio is 0.15 and 0.7, respectively. The UCS values of geopolymer-stabilized clay could reach 1.5 MPa at 14 days at ambient temperature, which is much higher than that of OPC-stabilized clay. The microstructure and mineralogy analyses indicated that the prolific hydration products, such as calcium silicate hydrate (C-S-H), calcium aluminum hydrate (C-A-H), and calcium aluminum silicate hydrate (C-A-S-H), contributed greatly to strengthen the soft clay by forming the soil skeleton and infilling among clay particles, while sodium aluminosilicate (N-A-S-H) gel is only served to fill the part of porosities in the soil and cannot effectively enhance the UCS of the one-part geopolymer-stabilized soft clay. This paper results suggested that one-part GGBFS-FA–based geopolymers have the potential to replace OPC in the manufacture of stabilized soft clay.

scholarly journals EFFECTS OF MIX PROPORTION ON ELECTRICAL RESISTIVITY OF CONCRETE WITH FLY ASH

2017 ◽  
Vol 7 (2) ◽  
pp. 53-65
Author(s):  
Su Wai Hnin ◽  
Pakawat Sancharoen ◽  
Somnuk Tangtermsirikul
Keyword(s):  
Compressive Strength ◽  
Electrical Resistivity ◽  
Fly Ash ◽  
Chloride Penetration ◽  
Mix Proportion ◽  
Binder Ratio ◽  
Saturated Concrete ◽  
Paste Content ◽  
Water Saturated ◽  
Water Binder Ratio

The aim of this paper is to investigate the effects of mix proportion on electrical resistivity of concrete with fly ash. The electrical resistivity of concrete is measured by using four Wenner probes. The varied parameters in this study were water/binder ratio, fly ash content, and paste content. Electrical resistivity of water-saturated concrete at several different ages was studied and compared with compressive strength and rapid chloride penetration. Based on experimental results, a good relationship was obtained between results of compressive strength and rapid chloride penetration with electrical resistivity of concrete. The results of this study can be applied further to predict electrical resistivity of concrete when mix proportions are provided. According to the results, lower water/binder ratio concrete had higher resistivity than those with higher water/binder ratios. When cement was replaced at 40% by fly ash, electrical resistivity increased four times when compared to that of OPC concrete.

An Abrasion Damage of Fly Ash Concretes Previously Subjected to Scaling

2016 ◽  
Vol 258 ◽  
pp. 587-590
Author(s):  
Aneta Nowak-Michta
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Abrasion Resistance ◽  
Air Entrainment ◽  
Binder Ratio ◽  
Abrasion Damage ◽  
Water Binder Ratio ◽  
Class F

Effect of quantity and quality of fly ash and compressive strength of concretes with their addition on abrasion resistance previously subjected to scaling is analyzed in the paper. The abrasion resistance was measured in Böhme test according to EN 1338: 2005. The cement was replaced with 20, 35, and 50% of Class F siliceous fly ash in three categories of losses on ignition A, B and C by mass. The water-binder ratio, the air-entrainment and the workability of mixtures were maintained constant at 0.38, 4,5% and 150 mm respectively.Prior scaling causes a decrease in abrasion resistance of fly ash concretes. In addition, both quantitative and qualitative fly ash parameters and compressive strength have an influence on abrasion damage.

Application of Sulfoaluminate Cement for Solidification/Stabilization of Fly Ash from Municipal Solid Waste Incinerators

2012 ◽  
Vol 178-181 ◽  
pp. 795-798 ◽  
Author(s):  
Qi Na Sun ◽  
Jing Miao Li ◽  
Bao Quan Huo ◽  
Ji Bing Wang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Municipal Solid Waste ◽  
Solid Waste ◽  
High Performance ◽  
Curing Time ◽  
Leaching Toxicity ◽  
Binder Ratio ◽  
Waste Incinerators ◽  
Water Binder Ratio

Sulfoaluminate cement (SAC) was utilized for the solidification/stabilization of fly ash from municipal solid waste (MSW) incinerators. The effects of fly ash amount and water/binder ratio were investigated on compressive strength and heavy metals leaching toxicity of solidified matrices at different curing times. The results showed that prolonged curing time, lower fly ash amount and water/binder ratio enhanced the compressive strength and decreased the leaching concentrations of Zn, Pb and Cu. For 28 days cured matrices with fly ash amount 50% and water/binder ratio 0.30, the compressive strength was 32.6 MPa and the leaching concentrations of Zn, Pb and Cu were 14.73, 0.75 and 0.43 mg/L respectively. The leaching concentrations of Zn, Pb and Cu met the demand of GB 5085.3-2007. SAC is proved to be effective for MSW incinerator fly ash solidification/stabilization and high performance matrices for disposal and reuse may be achieved with further formula optimization.

Effect of High Volumes of Fly Ash on Flowability and Drying Shrinkage of Engineered Cementitious Composites

2011 ◽  
Vol 675-677 ◽  
pp. 61-64
Author(s):  
Yu Zhu ◽  
Ying Zi Yang ◽  
Yan Yao
Keyword(s):  
Fly Ash ◽  
Drying Shrinkage ◽  
Ash Content ◽  
Experimental Results ◽  
Replacement Ratio ◽  
Slump Flow ◽  
Binder Ratio ◽  
Deformation Test ◽  
Flow Deformation ◽  
Water Binder Ratio

In order to investigate flowability and drying shrinkage of ECC, mini-slump flow deformation test and drying shrinkage are employed to analyse the influence of fly ash on the flowability and shrinkage of ECC. The water-binder ratio is kept at 0.25. The replacement ratio of cement by fly ash is 50%, 60%, 70% and 80%, respectively. The experimental results show that fluidity of fresh cment paste increases obviously as the fly ash becomes larger. The drying shrinkage of ECC specimens is greatly reduced as the content of fly ash increases from 50% to 80%. The measured drying shrinkage strian of ECC specimens with 80% fly ash at 28 days is less than 1000×10-6. 25% reduction of drying shrinkage of ECC is found when the fly ash content increases from 50% to 80%.

Theoretical and Experimental Research on Compressive Strength of High Fly-Ash Content Concrete

2011 ◽  
Vol 477 ◽  
pp. 257-262 ◽  
Author(s):  
Hong Mei Ai ◽  
Li Jiu Wang ◽  
Jing Wei ◽  
Jun Ying Bai ◽  
Pu Guang Lu
Keyword(s):  
Growth Rate ◽  
Compressive Strength ◽  
Fly Ash ◽  
Ash Content ◽  
Theoretical Formula ◽  
Term Strength ◽  
Single Factor ◽  
Binder Ratio ◽  
Water Binder Ratio

Introduced the concept of “Cementitious Coefficient” of fly ash, theoretical formula of strength of HFCC at a certain age was found with two variables: actual water-binder ratio and micro-aggregate-binder ratio. Development regularity of compressive strength of HFCC was studied and formula of long-term strength coefficient D28t was settled. Influence of actual water-binder ratio and micro-aggregate-binder ratio on long-term strength of HFCC was analyzed. Experimental results showed that along with the single-factor increase of actual water-binder ratio and micro-aggregate-binder ratio, growth rate of long-term strength of HFCC increased; influence of actual water-binder ratio was deeper than that of micro-aggregate-binder ratio.

Environmental Sustainability and Engineering Performance of Self-Compacting Mortar Incorporating Fly Ashes

2012 ◽  
Vol 253-255 ◽  
pp. 559-563 ◽  
Author(s):  
Putri Zulaiha Razi ◽  
Hashim Abdul Razak
Keyword(s):  
Fly Ash ◽  
Environmental Sustainability ◽  
Cement Content ◽  
Co2 Reduction ◽  
Fly Ashes ◽  
Cement Ratio ◽  
Low Co2 ◽  
Slump Flow ◽  
Binder Ratio ◽  
Water Binder Ratio

This paper investigated the effect of fly-ash on environmental sustainability and engineering performance of mortar. Samples of mortar were prepared with different dosage of superplasticizer to gives three ranges of workability that is normal slump flow, high slump flow and self-compacting flow. Cement content of 550 kg/m³, water/binder ratio of 0.35, binder/cement ratio of 2.00 and fly ash replacement 10%,20%, 40%, and 60% were adopted for the mix proportion.The relationship to look into are the potential of CO2 reduction in the mortar mixes while cement content were replace by fly ash. Results showed that self-compacting mixes with 20 % replacement by fly ash provides an increase in 28 day strength, enhancing the durability with low % of water absorption and reducing the environmental impact with low CO2 footprint. This gives it the best balance of durability and environmental sustainability impact of the mixes.

scholarly journals The effect of water binder ratio on strength development of class C fly ash geopolymer mortar prepared by dry geopolymer powder

2019 ◽  
Vol 258 ◽  
pp. 05032 ◽  
Author(s):  
Arie Wardhono
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Calcium Content ◽  
Strength Properties ◽  
Strength Development ◽  
Effect Of Water ◽  
High Calcium ◽  
Binder Ratio ◽  
Geopolymer Binder ◽  
Water Binder Ratio

The use of geopolymer binder as cement replacement material can reduce the amount of carbon dioxide gas produced during the Portland Cement manufacturing process. However, the main issue of geopolymer binder is in the mixing process of sodium silicate and NaOH which requires specialized knowledge and strict supervision. This paper reports the effect of water binder ratio on strength development of fly ash geopolymer mortar using dry geopolymer powder. Fly ash with high calcium content was used as primary material. The dry geopolymer powder was prepared by wet mixing method which was made by drying a mixture of NaOH solution and limestone for 24 hours. The variations of water to binder ratio were 0.30, 0.35, 0.40, 0.45, and 0.50. Strength properties were measured by compressive strength at the age of 7, 14 and 28 days. The results showed that the water binder ratio significantly affect the strength development of geopolymer mortar prepared by dry geopolymer powder. The water binder ratio of 0.40 gives the highest compressive strength of 10.3 MPa at 28 days. This suggests that the use of dry geopolymer powder on geopolymer mortar production can overcome the difficulties of geopolymer mortar mixing on site.

scholarly journals Influence of Water Binder Ratio on High Performance Concrete

2014 ◽  
Vol 8 (1) ◽  
pp. 18-21 ◽  
Author(s):  
N. Seshadri Sekhar ◽  
P.N. Raghunath
Keyword(s):  
Compressive Strength ◽  
Modulus Of Elasticity ◽  
Static Loading ◽  
High Performance ◽  
High Performance Concrete ◽  
Testing Machine ◽  
Influence Of Water ◽  
Binder Ratio ◽  
Average Compressive Strength ◽  
Water Binder Ratio

High performance concrete M60 cubes of 150 mm X 150 mm X 150 mm were tested experimentally under static loading. With the variation in the water binder ratios of 0.25, 0.28, 0.33, 0.39 and hyper plasticizer of 0.6%. 0.8%. 1.0%, 1.2% the cubes were cast and accordingly the cylinders were cast. For each ratio of water binder, 12 cubes and 2 cylinders were cast. Out of 12 cubes, 3 cubes were cured for 7 days, 3cubes for 15 days, 3 cubes for 21 days and the balance 3 cubes for 28 days. All the cubes were tested in a 2000kn compression testing machine. The load deflection curves, stress- strain curves were drawn for each cube and cylinder. The average compressive strength of each mix for different number of days of curing were calculated. The modulus of elasticity was calculated for each design mix.

Sign in / Sign up

Export Citation Format

Share Document