An Investigation about the Effect of Depth of Cut on Surface Integrity in Creep Feed Grinding of INC 792-5A

2011 ◽  
Vol 320 ◽  
pp. 163-169
Author(s):  
R. Ashofteh ◽  
A. Rastkerdar ◽  
S. Kolahdouz ◽  
A. Daneshi
Keyword(s):  
Surface Roughness ◽  
Surface Integrity ◽  
Structural Changes ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Cutting Depth ◽  
Creep Feed Grinding ◽  
Creep Feed ◽  
Micro Cracks ◽  
Average Grain Size

Creep-Feed Grinding(CFG) is one of the none-traditional machining in which form grinding to full depth is performed in limited number of passes. One of the most significant criteria which is taken into account to display valid machining parameters, is surface integrity. Surface integrity in CFG process is influenced by four main factors including surface roughness, superficial micro-crack, burning and changes in micro-hardness. According to prior investigations in CFG process, depth of cut plays an important role in surface integrity. In this study, the influence of cutting depth on workpiece surface integrity of cast nickel-based superalloy with alummina wheels, was investigated. During this study, a sample part was machined with variable depth of cut while the other parameters were Constant. After machining, surface roughness of each specimen was measured and in order to investigate existence and dimensional situation of surface micro-cracks, Chemical Etch + FPI and Thermal shock + FPI were performed. For determining micro-structural changes in ground specimens as a clarifier criteria in measuring the level of residual stress, a set of recrystallization processes were carried out on them and average grain size were measured. The results show, however, changing in depth of cut hasn't influenced on micro-cracks, quality of surface roughness has descended in terms of increasing the cutting depth.

Effect of SiC Particles on the Machining of Aluminum/SiC Composite

2009 ◽  
Vol 626-627 ◽  
pp. 219-224 ◽  
Author(s):  
Gao Feng Zhang ◽  
Yuan Qiang Tan ◽  
Bi Zhang ◽  
Zhao Hui Deng
Keyword(s):  
Surface Roughness ◽  
Aluminum Matrix ◽  
Volume Ratio ◽  
Damage Mechanism ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machined Surface ◽  
Aluminum Metal ◽  
Sic Particles ◽  
Average Grain Size

The objective of this study is to experimentally investigate the effect of reinforced SiC particles on the machining of Aluminum/SiC composite (15% volume ratio of SiC particles with average grain size 15m). Aluminum/SiC composite and aluminum metal were milled by a tungsten carbide endmill in this study. Based on the surface observation and surface roughness inspection, it is found that the machining parameters of Aluminum/SiC composite have optimum values, and that the surface roughness of aluminum/SiC composite is smaller than that of aluminum metal. when feedrate and depth of cut are smaller than limited values, satisfactory surface finish can be attainable, however, as the depth of cut and feedrate increases, the microcracks are first initiated at the interface of SiC particles and aluminum matrix, and then periodically macrocracks are formed on the machined surface, The damage mechanism during the machining of aluminum/SiC are discussed in this paper.

Effect of Machining Parameters on Surface Integrity in Dry Turning of Inconel 718

2013 ◽  
Vol 634-638 ◽  
pp. 2831-2834
Author(s):  
Xiao Li Zhu ◽  
Jin Fa Zhang ◽  
Wu Jun Chen ◽  
Ji Wen Deng
Keyword(s):  
Surface Roughness ◽  
Residual Stresses ◽  
Surface Integrity ◽  
Feed Rate ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Diffraction Method ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters

Surface quality including residual stresses and surface roughness due to turning operations in Inconel 718 were studied as a function of cutting speed, feed rate and depth of cut. By means of X-ray radiation diffraction method, the influence of cutting parameters on residual stress was investigated. The results show that dry cutting of Inconel 718 resulted in predominantly tensile residual stresses at the machined surface and the surface roughness increased with the increase of cutting parameters.The effects of the cutting parameters on surface integrity are investigated while employing the range analysis. From these results it was possible to select a combination of cutting speed, feed rate and depth of cut that generate favorable surface characteristics.

Parameter Optimization of Ball End Milling Process on Inconel 718 Using RSM and TLBO Algorithm

2015 ◽  
Vol 15 (3) ◽  
pp. 293-300 ◽  
Author(s):  
Nandkumar N. Bhopale ◽  
Nilesh Nikam ◽  
Raju S. Pawade
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Surface Integrity ◽  
Inconel 718 ◽  
Tool Path ◽  
End Milling ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Ball End Milling

AbstractThis paper presents the application of Response Surface Methodology (RSM) coupled with Teaching Learning Based Optimization Technique (TLBO) for optimizing surface integrity of thin cantilever type Inconel 718 workpiece in ball end milling. The machining and tool related parameters like spindle speed, milling feed, axial depth of cut and tool path orientation are optimized with considerations of multiple response like deflection, surface roughness, and micro hardness of plate. Mathematical relationship between process parameters and deflection, surface roughness and microhardness are found out by using response surface methodology. It is observed that after optimizing the process that at the spindle speed of 2,000 rpm, feed 0.05 mm/tooth/rev, plate thickness of 5.5 mm and 15° workpiece inclination with horizontal tool path gives favorable surface integrity.

Machining Evaluation of High-Speed Milling for Thin-Wall Machining of Al7075-T651

2014 ◽  
Vol 541-542 ◽  
pp. 785-791 ◽  
Author(s):  
Joon Young Koo ◽  
Pyeong Ho Kim ◽  
Moon Ho Cho ◽  
Hyuk Kim ◽  
Jeong Kyu Oh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Integrity ◽  
Cutting Forces ◽  
High Speed ◽  
Surface Condition ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Thin Wall ◽  
Machined Surface ◽  
High Speed Milling

This paper presents finite element method (FEM) and experimental analysis on high-speed milling for thin-wall machining of Al7075-T651. Changes in cutting forces, temperature, and chip morphology according to cutting conditions are analyzed using FEM. Results of machining experiments are analyzed in terms of cutting forces and surface integrity such as surface roughness and surface condition. Variables of cutting conditions are feed per tooth, spindle speed, and axial depth of cut. Cutting conditions to improve surface integrity were investigated by analysis on cutting forces and surface roughness, and machined surface condition.

Application of Taguchi Technique to Surface-Grinding of Mold Steel

2016 ◽  
Vol 689 ◽  
pp. 7-11 ◽  
Author(s):  
Y. Şahin ◽  
Senai Yalcinkaya
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Quality Characteristics ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Grinding Process ◽  
Machining Parameters ◽  
Taguchi Technique ◽  
Fluid Environment ◽  
Selection Of

The selection of optimum machining parameters plays a significant role for the quality characteristics of products and its costs for grinding. This study describes the optimization of the grinding process for an optimal parametric combination to yield a surface roughness using the Taguchi method. An orthogonal array and analysis of variance are employed to investigate the effects of cutting environment (A), depth of cut (B) and feed rate (C) on the surface roughness characteristics of mold steels. Confirmation experiments were conducted to verify the optimal testing parameters. The experimental results indicated that the surface finish decreased with cutting-fluid and depth of cut, but decreased with increasing feed rate. It is revealed that the cutting fluid environment had highest physical as well as statistical influence on the surface roughness (71.38%), followed by depth of cut (25.54%), but the least effect was exhibited by feed rate (1.62%).

Research on Prediction Model of Surface Roughness in Ultrasonic Polishing Nano-ZrO2 Ceramics

2009 ◽  
Vol 69-70 ◽  
pp. 128-132
Author(s):  
Ming Li Zhao ◽  
Bo Zhao ◽  
Yu Qing Wang ◽  
Guo Fu Gao
Keyword(s):  
Surface Roughness ◽  
Orthogonal Test ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Machining Parameters ◽  
Test Results ◽  
Work Situation ◽  
Table Speed ◽  
Abrasive Size ◽  
Regressive Analysis

The orthogonal test of surface roughness in ultrasonic polishing nano-ZrO2 ceramics was carried out in the present paper. Through the test, the influence of machining parameters on the surface roughness was investigated. The test results showed that the influence of abrasive size on surface roughness is the most remarkable, and the other important factors are the depth of cut, on/off work situation of ultrasonic generator, axial feed speed, and working table speed in turns. Furthermore, through the regressive analysis of test data, an empirical formula of surface roughness was established to select reasonable polishing parameters.

Investigation of Grinding Force and Surface Integrity of IC10 in Creep Feed Grinding

2020 ◽  
Author(s):  
Jun-chen Li ◽  
Wen-hu Wang ◽  
Rui-song Jiang ◽  
Xiao-fen Liu ◽  
Huang Bo ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal ◽  
Normal Force ◽  
Removal Rate ◽  
Tangential Force ◽  
Grinding Force ◽  
Wheel Speed ◽  
Creep Feed Grinding ◽  
Creep Feed

Abstract The IC10 superalloy material is one of the most important materials for aero-engine turbine blade due to its excellent performances. However, it is difficult to be machined because of its special properties such as terrible tool wear and low machined efficiency. The creep feed grinding is widely used in machining IC10 superalloy due to the advance in reducing tool wear, improving material removal rate and surface quality. The creep feed grinding is a promising machining process with the advantages of high material removal rate due to large cutting depth, long cutting arc and very slow workpiece, and its predominant features might have significant influence on the grinding force and surface quality for the workpiece. Hence, it is of great importance to study the grinding force and surface integrity in creep feed grinding IC10 superalloy. In this paper, a series of orthogonal experiments have been carried out and the effects of grinding parameters on the grinding force and the surface roughness are analyzed. The topographies and defects of the machined surface were observed and analyzed using SEM. The results of the experiments show that the tangential force is decreased with the workpiece speed increasing. However, there is no significant change in tangential force with the increasing of grinding depth and wheel speed. The normal force is decreased with the workpiece speed increasing when the workpiece speed is less than 150 mm/min, but when the workpiece speed is more than 150 mm/min the normal force is increased tardily. Moreover, the normal force is increased sharply with the increase of grinding depth and is increased slowly with the increase of wheel speed. In general, the surface roughness is increased with workpiece speed and grinding depth increasing, while the trend of increase corresponding that of workpiece speed is more evident. The value of the surface roughness is decreased with wheel speed increasing. And it is found out that the main defect is burning of the IC10 superalloy material in creep feed grinding by energy spectrum analysis of some typical topography in this study.

scholarly journals Effect of creep feed grinding on surface integrity and fatigue life of Ni3Al based superalloy IC10

2020 ◽  
Author(s):  
Shuaiqi ZHANG ◽  
Zhongxue YANG ◽  
Ruisong JIANG ◽  
Qichao JIN ◽  
Qiang ZHANG ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Surface Integrity ◽  
Creep Feed Grinding ◽  
Creep Feed

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

Sign in / Sign up

Export Citation Format

Share Document