Effect of Machining Parameters on Surface Integrity in Dry Turning of Inconel 718

2013 ◽  
Vol 634-638 ◽  
pp. 2831-2834
Author(s):  
Xiao Li Zhu ◽  
Jin Fa Zhang ◽  
Wu Jun Chen ◽  
Ji Wen Deng
Keyword(s):  
Surface Roughness ◽  
Residual Stresses ◽  
Surface Integrity ◽  
Feed Rate ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Diffraction Method ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters

Surface quality including residual stresses and surface roughness due to turning operations in Inconel 718 were studied as a function of cutting speed, feed rate and depth of cut. By means of X-ray radiation diffraction method, the influence of cutting parameters on residual stress was investigated. The results show that dry cutting of Inconel 718 resulted in predominantly tensile residual stresses at the machined surface and the surface roughness increased with the increase of cutting parameters.The effects of the cutting parameters on surface integrity are investigated while employing the range analysis. From these results it was possible to select a combination of cutting speed, feed rate and depth of cut that generate favorable surface characteristics.

Investigations on the Effect of CNC Dry Hard Turning Process Parameters on Surface Integrity: A Multi-performance Characteristics Optimization

2014 ◽  
Vol 14 (1) ◽  
pp. 23-30 ◽  
Author(s):  
Suha K. Shihab ◽  
Zahid A. Khan ◽  
Aas Mohammad ◽  
Arshad Noor Siddiquee
Keyword(s):  
Surface Roughness ◽  
Surface Integrity ◽  
Feed Rate ◽  
Hard Turning ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Influential Factor ◽  
Depth Of Cut ◽  
Micro Hardness ◽  
Dry Cutting

AbstractThe cutting parameters such as the cutting speed, the feed rate, the depth of cut, etc. are expected to affect the two constituents of surface integrity (SI), i.e., surface roughness and micro-hardness. An attempt has been made in this paper to investigate the effect of the CNC hard turning parameters on the surface roughness average (Ra) and the micro-hardness (μh) of AISI 52100 hard steel under dry cutting conditions. Nine experimental runs based on an orthogonal array of the Taguchi method were performed and grey relational analysis method was subsequently applied to determine an optimal cutting parameter setting. The feed rate was found to be the most influential factor for both the Ra and the μh. Further, the results of the analysis of variance (ANOVA) revealed that the cutting speed is the most significant controlled factor for affecting the SI in the turning operation according to the weighted sum grade of the surface roughness average and micro-hardness.

Optimization of Cutting Parameters for Turning Operation of Titanium Alloy Ti-6Al-4V Material Workpiece Using the Taguchi Method

2013 ◽  
Vol 685 ◽  
pp. 57-62
Author(s):  
Seyyed Pedram Shahebrahimi ◽  
Abdolrahman Dadvand
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Taguchi Method ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Material Tool

One of the most important issues in turning operations is to choose suitable parameters in order to achieve a desired surface finish. The surface finish in machining operation depends on many parameters such as workpiece material, tool material, tool coating, machining parameters, etc. The purpose of this research is to focus on the analysis of optimum cutting parameters to get the lowest surface roughness in turning Titanium alloy Ti-6Al-4V with the insert with the standard code DNMG 110404 under dry cutting condition, by the Taguchi method. The turning parameters are evaluated as cutting speed of 14, 20 and 28 m/min, feed rate of 0.12, 0.14 and 0.16 mm/rev, depth of cut of 0.3, 0.6 and 1 mm, each at three levels. The Experiment was designed using the Taguchi method and 9 experiments were conducted by this process. The results are analyzed using analysis of variance method (ANOVA). The results of analysis show that the depth of cut has a significant role to play in producing lower surface roughness that is about 63.33% followed by feed rate about 30.25%, and cutting speed has less contribution on the surface roughness. Also it was realized that with the use of the confirmation test, the surface roughness improved by 227% from its initial state.

Optimization of Surface Roughness in Turning Operation Using Firefly Algorithm

2015 ◽  
Vol 815 ◽  
pp. 268-272 ◽  
Author(s):  
Nur Farahlina Johari ◽  
Azlan Mohd Zain ◽  
Noorfa Haszlinna Mustaffa ◽  
Amirmudin Udin
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Firefly Algorithm ◽  
Volume Fraction ◽  
Optimization Problems ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machining Time

Recently, Firefly Algorithm (FA) has become an important technique to solve optimization problems. Various FA variants have been developed to suit various applications. In this paper, FA is used to optimize machining parameters such as % Volume fraction of SiC (V), cutting speed (S), feed rate (F), depth of cut (D) and machining time (T). The optimal machining cutting parameters estimated by FA that lead to a minimum surface roughness are validated using ANOVA test.

Surface Roughness Optimization of some Machining Parameters in Turning Operations Using Taguchi Method

2009 ◽  
Vol 62-64 ◽  
pp. 613-620 ◽  
Author(s):  
Ishaya Musa Dagwa
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Signal To Noise Ratio ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Confirmatory Test ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Turning Operations ◽  
Factors Affecting

In this study, an attempt has been made to optimize cutting parameters (cutting speed, depth of cut, and feed rate) in conventional turning operations. A Taguchi orthogonal array (L933) was used in surface roughness optimization of a solid round bar of mild steel material. The experimental runs were randomized; two skilled machinists were involved in the turning operation using the same machining parameters. ANOVA analysis was performed to identify the percentage contribution of the factors affecting surface roughness during machining. The optimal cutting combination was determined by using the signal-to-noise ratio and the following results were obtained; speed (level 2) = 55.m/min, depth of cut (level 3) = 0.08mm, and feed rate (levels 3) = at 0.08mm/rev. A prediction of surface roughness was carried out using the optimal setting followed by a confirmatory test on the lathe. The result shows that the confirmatory runs compared favourably (96.44%) with the predicted surface roughness.

scholarly journals Analysis of Surface Roughness and Cutting Forces in Hard Turning of 42CrMo4 Steel using Taguchi and RSM Method

Mechanika ◽  
2020 ◽  
Vol 26 (3) ◽  
pp. 231-241 ◽  
Author(s):  
Mustafa ÖZDEMİR ◽  
Mehmet Tuncay KAYA ◽  
Hamza Kemal AKYILDIZ
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Forces ◽  
Tangential Force ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Radial Force ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Feed Force

In this study, effects of cutting speed (V), feed rate (f), depth of cut (a) and tool tip radius (R) on  surface roughness (Ra, Rz, and Rt) and cutting forces (radial force (Fx), tangential force (Fy), and feed force (Fz)) in hard finish turning processes of hardened 42CrMo4 (52 HRC) material was investigated experimentally. Taguchi’s mixed level parameter design (L18) is used for the experimental design (2x1,3x3). The signal-to-noise ratio (S/N) was used in the evaluation of test results.  By using Taguchi method, cutting parameters giving optimum surface roughness and cutting forces were determined. Regression analyses are applied to predict surface roughness and cutting forces. Analysis of variance (ANOVA) is used to determine the effects of the machining parameters on surface roughness and cutting forces. According to ANOVA analysis, the most important cutting parameters were found to be feed rate for surface roughness and depth of cut among cutting forces.  By conducting validation experiments, optimization was seen to be applied successfully.

scholarly journals Effect of Cutting Parameters on Machinability of Hardened AISI 52100 Bearing Steel

2020 ◽  
Vol 3 (1) ◽  
pp. 474-481
Author(s):  
Mohammad Rafighi
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Bearing Steel ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Manufacturing Cost ◽  
Machining Parameters ◽  
Aisi 52100

In this study, the effects of machining parameters, namely feed rate, cutting speed and depth of cut on the surface roughness was investigated experimentally in hard turning of AISI 52100 bearing steel using cubic boron nitride insert under dry cutting condition. Taguchi method was utilized to reduce the number of trials to 9 for saving the time and manufacturing cost. The significant factor on the surface roughness was determined using analysis of variance. Furthermore, the optimum cutting parameter for reducing the surface roughness was obtained. The findings showed that the feed rate has the highest impact on surface roughness among any other cutting parameters, with 88.32% contribution.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

scholarly journals Investigations on Surface Roughness and Tool Wear Characteristics in Micro-Turning of Ti-6Al-4V Alloy

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2998 ◽  
Author(s):  
Kubilay Aslantas ◽  
Mohd Danish ◽  
Ahmet Hasçelik ◽  
Mozammel Mia ◽  
Munish Gupta ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Removal Rate ◽  
Cutting Speed ◽  
Small Diameter ◽  
Cutting Parameters ◽  
Ti6al4v Alloy ◽  
Depth Of Cut ◽  
Turning Process ◽  
Micro Turning

Micro-turning is a micro-mechanical cutting method used to produce small diameter cylindrical parts. Since the diameter of the part is usually small, it may be a little difficult to improve the surface quality by a second operation, such as grinding. Therefore, it is important to obtain the good surface finish in micro turning process using the ideal cutting parameters. Here, the multi-objective optimization of micro-turning process parameters such as cutting speed, feed rate and depth of cut were performed by response surface method (RSM). Two important machining indices, such as surface roughness and material removal rate, were simultaneously optimized in the micro-turning of a Ti6Al4V alloy. Further, the scanning electron microscope (SEM) analysis was done on the cutting tools. The overall results depict that the feed rate is the prominent factor that significantly affects the responses in micro-turning operation. Moreover, the SEM results confirmed that abrasion and crater wear mechanism were observed during the micro-turning of a Ti6Al4V alloy.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

Sign in / Sign up

Export Citation Format

Share Document