The Relationship of NaOH Molarity, Na2SiO3/NaOH Ratio, Fly Ash/Alkaline Activator Ratio, and Curing Temperature to the Strength of Fly Ash-Based Geopolymer

2011 ◽  
Vol 328-330 ◽  
pp. 1475-1482 ◽  
Author(s):  
M. M. A. Abdullah ◽  
H. Kamarudin ◽  
M. Bnhussain ◽  
I. Khairul Nizar ◽  
A.R. Rafiza ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Construction Industry ◽  
Curing Temperature ◽  
Test Results ◽  
Compression Tests ◽  
Naoh Solution ◽  
Alkaline Activator ◽  
Relationship Of ◽  
The Relationship

Geopolymer, produced by the reaction of fly ash with an alkaline activator (mixture of Na2SiO3 and NaOH solutions), is an alternative to the use of ordinary Portland cement (OPC) in the construction industry. However, there are salient parameters that affecting the compressive strength of geopolymer. In this research, the effects of various NaOH molarities, Na2SiO3/NaOH ratios, fly ash/alkaline activator, and curing temperature to the strength of geopolymer paste fly ash were studied. Tests were carried out on 50 x 50 x 50 mm cube geopolymer specimens. Compression tests were conducted on the seventh day of testing for all samples. The test results revealed that a 12 M NaOH solution produced the highest compressive strength for the geopolymer. The combination mass ratios of fly ash/alkaline activator and Na2SiO3/NaOH of 2.0 and 2.5, respectively, produced the highest compressive strength after seven days. Geopolymer samples cured at 60 °C produced compressive strength as high as 70 MPa.

Microstructure Study on Optimization of High Strength Fly Ash Based Geopolymer

2012 ◽  
Vol 476-478 ◽  
pp. 2173-2180 ◽  
Author(s):  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin ◽  
Mohammed Binhussain ◽  
Ismail Khairul Nizar ◽  
Rafiza Abd Razak ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
High Strength ◽  
Curing Temperature ◽  
Mix Design ◽  
Dense Matrix ◽  
Microstructural Characteristics ◽  
Naoh Solution ◽  
Alkaline Activator

The compressive strength and microstructural characteristics of fly ash based geopolymer with alkaline activator solution were investigated. The sodium hydroxide and sodium silicate were mixed together to form an alkaline activator. Three parameters including NaOH molarity, mix design (fly ash/alkaline activator ratio and Na2SiO3/NaOH ratio), and curing temperature were examined. The maximum strength of 71 MPa was obtained when the NaOH solution of 12M, fly ash/alkaline activator of 2.0, Na2SiO3/NaOH of 2.5 and curing temperature of 60°C were used at 7th days of testing. The results of SEM indicated that for geopolymer with highest strength, the structure was dense matrix and contains less unreacted fly ash with alkaline activator

scholarly journals Effect of Fly Ash on Compressive Strength, Drying Shrinkage, and Carbonation Depth of Mortar with Ferronickel-Slag Powder

2021 ◽  
Vol 11 (3) ◽  
pp. 1037
Author(s):  
Se-Jin Choi ◽  
Ji-Hwan Kim ◽  
Sung-Ho Bae ◽  
Tae-Gue Oh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Construction Industry ◽  
Bituminous Coal ◽  
Raw Materials ◽  
Drying Shrinkage ◽  
The Other ◽  
Test Results ◽  
Slag Powder ◽  
Ferronickel Slag

In recent years, efforts to reduce greenhouse gas emissions have continued worldwide. In the construction industry, a large amount of CO2 is generated during the production of Portland cement, and various studies are being conducted to reduce the amount of cement and enable the use of cement substitutes. Ferronickel slag is a by-product generated by melting materials such as nickel ore and bituminous coal, which are used as raw materials to produce ferronickel at high temperatures. In this study, we investigated the fluidity, microhydration heat, compressive strength, drying shrinkage, and carbonation characteristics of a ternary cement mortar including ferronickel-slag powder and fly ash. According to the test results, the microhydration heat of the FA20FN00 sample was slightly higher than that of the FA00FN20 sample. The 28-day compressive strength of the FA20FN00 mix was approximately 39.6 MPa, which was higher than that of the other samples, whereas the compressive strength of the FA05FN15 mix including 15% of ferronickel-slag powder was approximately 11.6% lower than that of the FA20FN00 mix. The drying shrinkage of the FA20FN00 sample without ferronickel-slag powder was the highest after 56 days, whereas the FA00FN20 sample without fly ash showed the lowest shrinkage compared to the other mixes.

Effect of Curing Time and Sintering to the Properties of Geopolymer Mortars

2017 ◽  
Vol 888 ◽  
pp. 184-187
Author(s):  
Salwa Ismail ◽  
Mohammad Faizal Mohd Razali ◽  
Izwan Johari ◽  
Zainal Arifin Ahmad ◽  
Shah Rizal Kasim
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Distilled Water ◽  
Curing Time ◽  
Pore Former ◽  
X Ray ◽  
Before And After ◽  
Naoh Solution ◽  
Added Water ◽  
Alkaline Activator

In this study, the geopolymer mortars were synthesized with fly ash (FA) and silica powder as aluminosilicate sources and a combination of sodium hydroxide (NaOH) solution, sodium silicate (Na2SiO3) solution and distilled water as alkaline activator. Commercial sago was used as a pore former in the mortars. The percentage of sago used were 10, 20 and 30 wt% of FA. The amount of added water used in each mixture was 5% by weight of FA, NaOH solution and Na2SiO3 solution. The formed geopolymer mortars were cured for 1, 3 and 7 days and sintered at 1000 °C. X-ray fluoresence (XRF) shown that FA contains higher amount of silica (SiO2) and alumina (Al2O3) which is important as aluminosilicate sources. The properties of the geopolymer mortars before and after sintered at 1000 °C have been investigated. The results show that geopolymer mortars with 10% of sago content with curing time of 7 days and sintered at 1000 °C give the highest compressive strength of 13.5 MPa.

scholarly journals The Relationship of Temperature and Compressive Strength on Geopolymer Mortar using Fly Ash-Based

2020 ◽  
Vol 885 ◽  
pp. 012019
Author(s):  
E Bachtiar ◽  
I Marzuki ◽  
Erdawaty ◽  
M F Junaedy ◽  
F Ramadhan ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Relationship Of ◽  
The Relationship

scholarly journals Effect of NaOH concentration and curing regime on geopolymer

2017 ◽  
Vol 10 (6) ◽  
pp. 1174-1181 ◽  
Author(s):  
C. N. LIVI ◽  
W. L. REPETTE
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Curing Temperature ◽  
Lower Amount ◽  
Alkali Concentration ◽  
X Ray Diffraction ◽  
Highest Weight ◽  
Thermogravimetric Data ◽  
Naoh Solution ◽  
Curing Regime

Abstract The effect of alkali concentration and curing temperature regime on fly ash-based geopolymer pastes was investigated in this study by using NaOH solutions. Prismatic specimens were molded, cured at 65 °C and 85 °C and submitted to flexural and compressive strength tests. Unreacted fly ash and geopolymers were characterized by X-ray diffraction and thermogravimetric analysis. In general, the mechanical strength was enhanced by increasing the molar concentration and the curing temperature. This trend was confirmed by thermogravimetric data. However, for a lower amount of NaOH there were no significant differences between the strength results. The mixture with the highest strength was obtained with the 16 M NaOH solution and curing temperature of 85 °C, which resulted in flexural strength of 4.20 MPa, compressive strength of 21.35 MPa and also the highest weight loss of 9.89%.

Mechanical Properties of Non-Cement Polymer Grout

2015 ◽  
Vol 1113 ◽  
pp. 80-85
Author(s):  
S.M. Nuria ◽  
A.B.A. Rahman ◽  
N.A.K. Hafizah ◽  
Yusof Ahmad ◽  
Azlan Adnan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Fine Sand ◽  
Strength Properties ◽  
Test Results ◽  
Compression Tests ◽  
Rapid Setting

This paper studies the effects of binder and filler composition to the strength properties of non-cement polyester grout (NCPG). The binder consisted of unsaturated polyester resin whereas the filler consisted of fine sand and fly ash. The composition of binder-to-filler ratios investigated were 0.43, 0.67, 1, 1.49, and 2.3. The mechanical properties of NCPG were investigated through flowability and compression tests. The test results show that the use of polyester resin combined with fine sand and fly ash produces good quality grout with high flowable rate, rapid setting, self-consolidating and high compressive strength.

Optimization of Alkaline Activator/Fly ASH Ratio on the Compressive Strength of Manufacturing Fly ASH-BASED Geopolymer

2011 ◽  
Vol 110-116 ◽  
pp. 734-739 ◽  
Author(s):  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Kamarudin ◽  
Omar A.K.A. Abdulkareem ◽  
Che Mohd Ruzaidi Ghazali ◽  
A.R. Rafiza ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Alkaline Solution ◽  
Room Temperature ◽  
High Strength ◽  
Constant Ratio ◽  
Optimum Amount ◽  
Molar Ratios ◽  
Naoh Solution ◽  
Alkaline Activator

Fly ash and a mixture of alkaline activators namely sodium silicate (Waterglass) and sodium hydroxide (NaOH) solution were used for preparing geopolymer. The aim of this research is to determine the optimum value of the alkaline activator/fly ash ratio. The effect of the oxide molar ratios of SiO2/Al2O3, water content of the alkaline activator and the Waterglass% content were studied for each Alkaline activator/fly ash ratio. The geopolymers were synthesized by the activation of fly ash with alkaline solution at three different alkaline activator/fly ash ratios which were 0.3, 0.35, and 0.4 at a specific constant ratio of waterglass/NaOH solution of 1.00. The geopolymers were cured at 70°C for 24 h and cured to room temperature. Results revealed that the alkaline activator/fly ash ratio of 0.4 has the optimum amount of alkaline liquid, which shows the highest rate of geopolymerization compared to other ratios. A high strength of 8.61 MPa was achieved with 0.4 of activator/fly ash ratio and 14% of waterglass content.

scholarly journals Synthesis of Geopolymer from Coal Fly Ash

2013 ◽  
Vol 30 ◽  
pp. 24-28
Author(s):  
Vinay Kumar Jha ◽  
Gautam Prasad Budhamagar
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coal Fly Ash ◽  
Chemical Society ◽  
Curing Temperature ◽  
Alkali Concentration ◽  
Curing Time ◽  
Naoh Solution ◽  
Maximum Compressive Strength

In the present work, geopolymers have been synthesized from coal fly ash (CFA) using NaOH and Na2SiO3 as activators. Some parameters like alkali concentration, amount of Na2SiO3 and curing time have been varied in order to improve the quality of geopolymeric product. The geopolymerization process has been performed using 3-8M NaOH solutions, Na2SiO3 to CFA mass ratios of 0.25-1.25 and curing time variation from 5-15 days. The curing temperature was fixed at 40ºC in all cases. In the variation of NaOH concentration, the maximum compressive strength of 2.3 MPa was obtained with CFA treated with 6M NaOH solution. Similarly during the variation of amount of Na2SiO3, the maximum compressive strength of 17.6 MPa was obtained with Na2SiO3 to CFA mass ratio of 1.25. Furthermore, the compressive strength was found increasing up to 20.3 MPa with increasing curing time.DOI: http://dx.doi.org/10.3126/jncs.v30i0.9331Journal of Nepal Chemical Society Vol. 30, 2012 Page:  24-28 Uploaded date: 12/16/2013 

Effect of the Combined Using of Fly Ash and Granulated Blast Furnace Slag on Properties of Cementless Alkali-Activated Mortar

2011 ◽  
Vol 287-290 ◽  
pp. 916-921
Author(s):  
Kyung Taek Koh ◽  
Gum Sung Ryu ◽  
Si Hwan Kim ◽  
Jang Hwa Lee
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Curing Temperature ◽  
Mixture Ratio ◽  
Granulated Blast Furnace Slag ◽  
Alkaline Activator ◽  
Furnace Slag ◽  
Alkali Activated

This paper examines the effects of the mixture ratio of fly ash/slag, the type of alkaline activators and curing conditions on the workability, compressive strength and microstructure of cementless alkali-activated mortar. The investigation showed that the mixture ratio of fly ash/slag and the type of alkaline activator have significant influence on the workability and strength, whereas the curing temperature has relatively poor effect. An alkali-activated mortar using a binder composed of 50% of fly ash and 50% of granulated blast furnace slag and alkaline activator made of 9M NaOH and sodium silicate in proportion of 1:1 is seen to be able to develop a compressive strength of 65 MPa at age of 28 days even when cured at ambient temperature of 20°C.

Effect of white soil substitution on fly ash based mortar geopolymers with sodium hydroxide activator

2020 ◽  
Vol 26 (1) ◽  
pp. 9-16
Author(s):  
Yulita Arni Priastiwi ◽  
Arif Hidayat ◽  
Dwi Daryanto ◽  
Zidny Salamsyah Badru
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Moisture Content ◽  
Sodium Hydroxide ◽  
Modulus Of Elasticity ◽  
Physical And Mechanical Properties ◽  
Test Results ◽  
Alkaline Activator ◽  
Made In

The presence of white soil in a geopolymer mortar affects the physical and mechanical properties of the mortar itself, especially in compressive strength, density and modulus of elasticity produced. Geopolymer mortar composed of fly ash, sand, water, and NaOH which acts as an alkaline activator compared to mortar from the same material, but white soil from Kupang is added as a substitution of fly ash. Specimens are made in six variations. Geopolymer mortar composers using a ratio of 1 binder: 3 sand with w/b of 0.5. Binder composed of fly ash with white soil substitution of 0; 5; 10; 15; 20 and 30% by weight of fly ash. An activator NaOH 8M solution was added to the mixture. Both white soil and fly ash pass of sieve no. 200 with a moisture content of 0%. Mortar made measuring 5x5x5 cm. The mortar was treated by the oven of method at 60 oC for 24 hours until the mortar does not change in weight. The test results show geopolymer mortar with 15% substitution of white soil to fly ash has the highest compressive strength, density and modulus of elasticity among other variations. In all mortar variations, compressive strength at 14 days has reached 75% of strength at 28 days.

Sign in / Sign up

Export Citation Format

Share Document