Microwave Synthesis of Nano-Titanium Carbide

2011 ◽  
Vol 399-401 ◽  
pp. 561-564 ◽  
Author(s):  
Ping An Liu ◽  
Qing Song Yang ◽  
An Ze Shui ◽  
Hui Wang ◽  
Xiao Su Cheng ◽  
...  
Keyword(s):  
Particle Size ◽  
Low Temperature ◽  
Carbon Black ◽  
Titanium Carbide ◽  
Microwave Synthesis ◽  
Average Particle Size ◽  
Synthesis Method ◽  
Synthesis Temperature ◽  
Synthesis Rate ◽  
Average Particle

A new synthesis technology of titanium carbide with microwave is introduced in this article. Microwave synthesis technology is a fast and relatively low temperature of synthesis method. Nano-titanium carbide powders were synthesized by carbothermal reduction of titanium dioxide and carbon black with the microwave synthesis method at 1100°C-1400°C in argon gas atmosphere. Nano-TiO2powder and carbon black were used as raw materials. The TiC powders were characterized with the XRD and TEM. The experimental results show that the synthesis rate is quick, even at relatively low synthesis temperature. The average particle size of the TiC powders synthesized by the microwave synthesis technology under low temperature (<1300°C) is less than 50nm, and the average particle size augments with increasing the microwave synthesis temperature and time.

Formation of metal-carbon nanocomposites based on Cu-Fe alloy nanoparticles and carbonized polyacrylonitrile

2021 ◽  
Vol 1 ◽  
pp. 58-66
Author(s):  
A.A. Vasilev ◽  
◽  
E.L. Dzidziguri ◽  
M.N. Efimov ◽  
D.G. Muratov ◽  
...  
Keyword(s):  
Particle Size ◽  
Carbon Nanostructures ◽  
Average Particle Size ◽  
Synthesis Method ◽  
Carbon Matrix ◽  
Synthesis Temperature ◽  
Average Particle ◽  
Synthesis Of Nanoparticles ◽  
Fe Nanoparticles ◽  
Average Size

A method for the synthesis of nanoparticles of the Cu-Fe bimetallic system with limited mutual solubility of the components is proposed. The synthesis method consists of a one-stage process of IR pyrolysis of precursors in the form of films obtained from a joint solution of polyacrylonitrile and hydrates-nitrates of iron and copper. The effect of the synthesis temperature on the structure formation of the nanocomposites and the phase composition of bimetallic Cu-Fe nanoparticles dispersed in the carbon matrix was studied. The analysis showed a simultaneous presence of Fe and Cu phases in nanocomposites, presumably with a low solubility of the components. The average particle size is 14-17 nm and changes insignificantly with an increase in the synthesis temperature from 400 to 700°C. An increase in the synthesis temperature to 800°C led to a broadening of the particle size distribution and the increase in the average size. The formation of complex carbon nanostructures on Cu-Fe nanoparticles is found.

Microemulsion Synthesis of Nd0.5Ca0.5MnO3 and Nd0.5Sr0.5MnO3 Nanoparticles

2006 ◽  
Vol 962 ◽  
Author(s):  
Z. Q. Wang ◽  
K. B. Yin ◽  
F. Gao ◽  
K. F. Wang ◽  
Z. F. Ren ◽  
...  
Keyword(s):  
Particle Size ◽  
Average Particle Size ◽  
Synthesis Method ◽  
Charge Order ◽  
Freezing Behavior ◽  
Average Particle ◽  
High Quality ◽  
Spin Freezing ◽  
Microemulsion Synthesis ◽  
Order State

ABSTRACTNd0.5Ca0.5MnO3 (NCMO) and Nd0.5Sr0.5MnO3 (NSMO) nanoparticles have been synthesized using microemulsion synthesis method, with hexamethylene alkyl, a mixture of OP and 1-hexanol, NaOH as oil phase, surfactant, and precipitating agent, respectively. The phase formation of NCMO and NSMO nanoparticles was examined. The final NCMO and NSMO nanoparticles have average particle size of 24 and 50 nm, respectively, and present high-quality crystallinity. Measurements of the magnetic properties suggest that the charge-order state favored for bulk NCMO phase collapses in NCMO nanoparticles. The spin freezing behavior for both NCMO and NSMO nanoparticles was identified.

scholarly journals Structural and Optical Properties of Silicon Carbide Powders Synthesized from Organosilane Using High-Temperature High-Pressure Method

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 3111
Author(s):  
Evgeny A. Ekimov ◽  
Vladimir S. Krivobok ◽  
Mikhail V. Kondrin ◽  
Dmitry A. Litvinov ◽  
Ludmila N. Grigoreva ◽  
...  
Keyword(s):  
Particle Size ◽  
Optical Properties ◽  
Average Particle Size ◽  
Synthesis Temperature ◽  
Narrow Particle Size Distribution ◽  
High Tech ◽  
Average Particle ◽  
Coupled Modes ◽  
Dominant Type ◽  
High Structure

The development of new strategies for the mass synthesis of SiC nanocrystals with high structure perfection and narrow particle size distribution remains in demand for high-tech applications. In this work, the size-controllable synthesis of the SiC 3C polytype, free of sp2 carbon, with high structure quality nanocrystals, was realized for the first time by the pyrolysis of organosilane C12H36Si6 at 8 GPa and temperatures up to 2000 °C. It is shown that the average particle size can be monotonically changed from ~2 nm to ~500 nm by increasing the synthesis temperature from 800 °C to 1400 °C. At higher temperatures, further enlargement of the crystals is impeded, which is consistent with the recrystallization mechanism driven by a decrease in the surface energy of the particles. The optical properties investigated by IR transmission spectroscopy, Raman scattering, and low-temperature photoluminescence provided information about the concentration and distribution of carriers in nanoparticles, as well as the dominant type of internal point defects. It is shown that changing the growth modes in combination with heat treatment enables control over not only the average crystal size, but also the LO phonon—plasmon coupled modes in the crystals, which is of interest for applications related to IR photonics.

Effect of Poly(Vinyl Pyrrolidone) on Dispersing Carbon Black Particles

2013 ◽  
Vol 796 ◽  
pp. 432-436
Author(s):  
Xia Yuan
Keyword(s):  
Particle Size ◽  
Zeta Potential ◽  
Carbon Black ◽  
Ultrasonic Method ◽  
Aqueous Media ◽  
Average Particle Size ◽  
Sodium Dodecyl ◽  
Vinyl Pyrrolidone ◽  
Average Particle ◽  
Poly Vinyl Pyrrolidone

The effects of poly (vinyl pyrrolidone)(PVP) on dispersing carbon black (CB) particles were investigated by measuring Z-average particle size, Zeta potential and centrifugal stability of CB dispersions. Addition of PVP in a dispersing medium significantly reduces the size of suspended CB particles, especially in water. The dispersing efficiency of PVP was found to have been enhanced by adding an anionic surfactant, sodium methylenedinaphthalene disulphonate (NNO) in the aqueous media. The particle size of CB dispersed with PVP and NNO was 175.7 nm, significantly smaller than that dispersed with PVP and sodium dodecyl sulfate (SDS). The performance of PVP-encapsulated CB particles and that of PVP-adsorbed CB particles were also compared. The particle size and Zeta potential of PVP-encapsulated CB particles were similar to those of PVP-adsorbed CB particles using ultrasonic method, but the centrifugal stability of PVP-encapsulated CB dispersions was significantly improved. The relative absorbency of PVP/CB dispersions was increased from 42.0% to 63.7%. However, the PVP-encapsulated layer can be destroyed by prolonged ultrasonic treatment because the ultrasound over a long period of time can not only break up the flocculation bridge in the crosslinking matrix of PVP, but also flake off the PVP shells on the surface of CB particles.

scholarly journals Effect of dopants [Gd3+, Sm3+, Ca2+, Sr2+ and Ba2+] on the performance characteristics of ceria based electrolytes for application in solid oxide fuel cells

2014 ◽  
Vol 10 (2) ◽  
Author(s):  
M.L. Reni ◽  
A. Samson Nesaraj
Keyword(s):  
Particle Size ◽  
Fuel Cells ◽  
Low Temperature ◽  
Solid Oxide Fuel Cells ◽  
Average Particle Size ◽  
Solid Oxide ◽  
Narrow Particle Size Distribution ◽  
Average Particle ◽  
Doped Ceria ◽  
Oxide Fuel

Doped CeO2 based materials are now-a-days proposed as alternate electrolyte materials for solid oxide fuel cells (SOFCs) working at low temperature (~723 – 873 K). In this research work, nanoparticles of CeO2 doped with Gd3+, Sm3+, Ca2+, Sr2+ and Ba2+were prepared by a simple homogeneous chemical precipitation method. The prepared materials (after heat treatment at 1023 K for 2 hours) were systematically characterized by XRD, EDAX analysis, FTIR , particle size analysis and SEM.  Lattice parameters were calculated from the XRD data. The XRD results indicate that all the doped ceria samples studied are single phase with a cubic fluorite structure. The average particle size of the doped ceria powder was about 48 – 115 nm and the particles have shown narrow particle size distribution patterns. AC impedance spectroscopy studies performed on the sintered specimens have shown better oxide ion conductivity values and hence these materials may be suitable for application as electrolyte materials in solid oxide fuel cells working at low temperature (~723 – 873 K). ________________________________________GRAPHICAL ABSTRACT

Carbon Black in Rubber Compounding

1941 ◽  
Vol 14 (1) ◽  
pp. 98-112 ◽  
Author(s):  
D. Parkinson
Keyword(s):  
Particle Size ◽  
Carbon Black ◽  
Fine Particle ◽  
Average Particle Size ◽  
Average Particle ◽  
Small Particles ◽  
Surface Development ◽  
Fine Particle Size ◽  
Filler Reinforcement ◽  
Methods Of Measurement

Abstract The mechanism of filler reinforcement has not yet been fully explained, but there is general agreement that an important, probably the most important, factor is the enormous surface development between the rubber and filler due to the fine particle size of the filler. Explanations have been attempted to show how small particles can cause reinforcement, but a complete theory of the phenomenon which accounts for all the facts is still awaited. Particle size oj carbon blacks.—A knowledge of this property is important in an understanding of the mechanism of reinforcement by carbon black. Because of the difficulty of distinguishing between ultimate particles and compact aggregates, and because the particles themselves are too small to be resolved in an ordinary microscope, the usual microscopical methods of measurement are inapplicable. Ultramicroscopical methods have been used with some success, the results obtained by the method of Gehman and Morris being probably the most reliable. These authors quote an average particle size of 61µµ for a sample of a standard rubber gas black (Micronex). The figures given for P-33 black, Shawinigan acetylene black and Thermatomic black are 159µµ, 130µµ and 1120µµ, respectively.

The Photocatalytic Degradation of Methomyl over TiO2 Nanopowder Prepared by the Low Temperature Solvothermal Route

2014 ◽  
Vol 804 ◽  
pp. 209-212 ◽  
Author(s):  
Pusit Pookmanee ◽  
Isara Phiwchai ◽  
Sorachon Yoriya ◽  
Ratchadaporn Puntharod ◽  
Supaporn Sangsrichan ◽  
...  
Keyword(s):  
Particle Size ◽  
Low Temperature ◽  
Photocatalytic Degradation ◽  
High Performance ◽  
Average Particle Size ◽  
Ammonium Hydroxide ◽  
Average Particle ◽  
Mixed Solution ◽  
Liquid Chromatograph ◽  
Solvothermal Route

Titanium dioxide (TiO2) nanopowder was prepared by the low temperature solvothermal route with starting chemicals containing titanium isopropoxide, ammonium hydroxide, nitric acid and ethanol in a PTFE–lined autoclave. The final pH of the mixed solution was 1 and treated at 100 °C for 2–6 h. The white precipitated was filtered and dried in an oven at 80 °C for 24 h. The phase transition was characterized by X–ray diffractometer (XRD). Single phase anatase structure was obtained without calcination step. The morphology and particle size of TiO2nanopowder was investigated by scanning electron microscope (SEM). The average of TiO2nanopowder size was 80–120 nm. The average particle size increased with temperature and time increased. The photocatalytic degradation of methomyl in natural water was studied by high performance liquid chromatograph (HPLC). The percentage of methomyl was decreased in the presence of 34, 23 and 24 over TiO2nanopowder prepared by the low temperature solvothermal route at 100 °C for 2, 4 and 6 h, respectively.

Mössbauer Investigation of γ-Fe2O3 Nanocrystals in Silica Matrix Prepared by the Sol-gel Method

2002 ◽  
Vol 57 (3-4) ◽  
pp. 154-158 ◽  
Author(s):  
C. Cannas ◽  
G. Concas ◽  
F. Congiu ◽  
A. Musinu ◽  
G. Piccaluga ◽  
...  
Keyword(s):  
Particle Size ◽  
Low Temperature ◽  
Sol Gel ◽  
Average Particle Size ◽  
Volume Ratio ◽  
Silica Matrix ◽  
Blocking Temperature ◽  
Average Particle ◽  
Gel Method ◽  
Sol Gel Method

A series of Fe2O3-SiO2 nanocomposites (25 weight % of Fe2O3) has been prepared using a sol-gel method. Samples showing different features were obtained by varying the evaporation conditions acting on the surface / volume ratio of the starting sol. The samples were investigated using Mössbauer spectroscopy at low temperature. The Fe2O3 nanoparticles have been identified as maghemite ( γ-Fe2O3) particles. The samples show a superparamagnetic behavior with a blocking temperature that depends on the average particle size.

Effect of Gelation Process on Preparation of Aluminum Titanate Ultrafine Powder by Hydrolytic Sol-Gel Method

2013 ◽  
Vol 745-746 ◽  
pp. 690-695
Author(s):  
Wei Hui Jiang ◽  
Quan Zhang ◽  
Jian Min Liu ◽  
Qing Xia Zhu ◽  
Li Feng Miao
Keyword(s):  
Particle Size ◽  
Sol Gel ◽  
Average Particle Size ◽  
Ultrafine Powder ◽  
Synthesis Rate ◽  
Average Particle ◽  
Aluminium Nitrate ◽  
Crystal Water ◽  
Gelation Process ◽  
Solvothermal Treatment

Aluminium titanate (AT) ultrafine powder was prepared via hydrolytic sol-gel (HSG) method using aluminium nitrate (Al (NO3)3·9H2O) and titanium tetrachloride (TiCl4) as precursors as well as ethanol as solvent. Water required for hydrolysis reaction was supplied by the crystal water of aluminium nitrate itself. The effect of gelation processes, i.e. reflux and solvothermal treatment, on synthesis of AT powder was investigated by means of DTA-TG, XRD, SEM, and TEM, etc. The result shows that the gelation process has significant effect on the synthesis of AT powder. By reflux process, AT powder was synthesized at 1350 °C with average particle size above 1μm and serious agglomeration. Through solvothermal treatment process, however, AT powder with average particle size less than 150 nm was prepared at 1050 °C at a relatively high synthesis rate, which is due to the refinement reactants by the solvothermal treatment.

scholarly journals Preparation and Evaluation of Sunflower Oil Nanoemulsion As a Sunscreen

2019 ◽  
Vol 7 (22) ◽  
pp. 3757-3761
Author(s):  
Anayanti Arianto ◽  
Cindy Cindy
Keyword(s):  
Particle Size ◽  
High Temperature ◽  
Low Temperature ◽  
Sunflower Oil ◽  
Room Temperature ◽  
Ph Value ◽  
Average Particle Size ◽  
Tween 80 ◽  
Average Particle ◽  
Spontaneous Emulsification

BACKGROUND: There are a lot of different types of sunscreen products (oils, sticks, gels, creams, lotions) which can be found on the world's market. Sunscreen product that contains active chemical ingredients sometimes has harmful effects on the skin. Sunflower oil contains vitamin E and acts as a natural sunscreen which can absorb UVB light. The average droplet size of nanoemulsion is between 100 and 500 nm and do not show the problems of stability (creaming, flocculation, coalescence, and sedimentation), which are commonly associated with macroemulsions. AIM: The aim of this study was to prepare and evaluate the sunflower oil nanoemulsion as a sunscreen. METHODS: Sunflower oil nanoemulsions were prepared by spontaneous emulsification method with 3 formulas F1 (Tween 80 38%, sorbitol 22%), F2 (Tween 80 36%, sorbitol 24%), F3 (Tween 80 34%, sorbitol 26%) and 5% sunflower oil as a sunscreen substance. The nanoemulsions were evaluated for particle size, physical stability in room temperature (25 ± 2°C), low temperature (4 ± 2°C) and high temperature (40 ± 2°C) during experiment for 12 weeks of storage, centrifugation at 3750 rpm for 5 hours, viscosity, pH, freeze-thaw test and sun protection value (SPF) value by in vitro. RESULTS: The results of nanoemulsion evaluation showed that nanoemulsion formula F1 had the smallest average particle size of 124.47 nm with yellowish colour, clear, transparent, pH value (6.5 ± 0.1), viscosity value (225 ± 25 cP), did not show any separation or creaming in the centrifugation, and stable during experiment for 12 weeks of storage at room temperature, low temperature and high temperature. The SPF value of all nanoemulsion preparations was higher than that of the emulsion. CONCLUSION: The preparation of the sunflower oil nanoemulsion with a ratio of Tween 80 and sorbitol (38: 22) produces a stable nanoemulsion during the experiment for 12 weeks storage at the room, low and high temperature. The nanoemulsion preparation has higher SPF values compared to the emulsion. This nanoemulsion formulation could be considered more effective in sunscreen cosmetic use compare to the emulsion.

Sign in / Sign up

Export Citation Format

Share Document