Mechanical Properties of Composites with Embedded FBG Sensors in Manufacturing Engineering

2012 ◽  
Vol 583 ◽  
pp. 263-267
Author(s):  
Wen Juan Wang ◽  
Hao Song ◽  
Wei Guo ◽  
Nan Sheng
Keyword(s):  
Mechanical Properties ◽  
Optical Fibers ◽  
Continuous Monitoring ◽  
Reference Value ◽  
Sensitivity Coefficient ◽  
Composites Manufacturing ◽  
Fbg Sensor ◽  
Fbg Sensors ◽  
Manufacturing Engineering ◽  
Properties Of Composites

FBG (fiber Bragg grating) sensors are appropriate for embedding in composites manufacturing engineering. Influence of embedding FBG sensors on the composites tension, compression, CAI properties was studied in this paper. Results identified that the mechanical properties decreased obviously when a certain volume content of optical fibers embedded. FBG sensor permits the continuous monitoring of the host material when embedded in the middle 0 degree layer, consistent with strain gauges. Sensitivity coefficient of FBG sensor embedded is almost the same as that not embedded. It offers important reference value on the application of FBG sensors in aerospace composites.

scholarly journals Measurement of Mechanical and Thermal Strains by Optical FBG Sensors Embedded in CFRP Rod

2019 ◽  
Vol 2019 ◽  
pp. 1-6
Author(s):  
Keunhee Cho ◽  
Sung Tae Kim ◽  
Young-Hwan Park ◽  
Jeong-Rae Cho
Keyword(s):  
Mechanical Properties ◽  
Thermal Expansion ◽  
Thermal Expansion Coefficient ◽  
Expansion Coefficient ◽  
Strain Sensor ◽  
Thermal And Mechanical Properties ◽  
Fbg Sensor ◽  
Thermal Test ◽  
Fbg Sensors ◽  
Thermooptic Coefficient

The present study intends to provide the photoelastic coefficient and thermal expansion coefficient needed to use an FBG-embedded CFRP rod (smart rod) as strain sensor. Due to the monolithic combination of the FBG sensor with a CFRP rod, the smart rod is likely to exhibit thermal and mechanical properties differing from those of the bare FBG sensor. A tensile test showed that the photoelastic coefficient of the smart rod is 0.204, which is about 7.3% lower than the 0.22 value of the bare optical FBG. Moreover, the thermal expansion coefficient of the smart rod obtained through a thermal test appeared to be negative with a low value of −0.190×10−6/°C. Consequently, the temperature dependence of the smart rod is mainly expressed by means of the thermooptic coefficient. Compared to the bare FBG sensor, the smart rod is easier to handle and can measure compressive strains, which make it a convenient sensor for various concrete structures.

Effect of Titanium Carbide Particles on Mechanical Properties of Aluminum Matrix Composites

2017 ◽  
Vol 5 (2) ◽  
pp. 20-30
Author(s):  
Zaman Khalil Ibrahim
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Compression Strength ◽  
Volume Fraction ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Powder Metallurgy Technique ◽  
Carbide Particles ◽  
Properties Of Composites

In this research aluminum matrix composites (AMCs) was reinforced by titanium carbide (TiC) particles and was produced. Powder metallurgy technique (PM) has been used to fabricate AMCs reinforced with various amounts (0%, 4%, 8%, 12%, 16% and 20% volume fraction) of TiC particles to study the effect of different volume fractions on mechanical properties of the Al-TiC composites. Measurements of compression strength and hardness showed that mechanical properties of composites increased with an increase in volume fraction of TiC Particles. Al-20 % vol. TiC composites exhibited the best properties with hardness value (97HRB) and compression strength value (275Mpa).

Frost Heaving Soil Road Use Synthetic Adhesive Reinforcement Method

2013 ◽  
Vol 740 ◽  
pp. 759-762
Author(s):  
Hao Zeng Bao
Keyword(s):  
Mechanical Properties ◽  
Industrial Waste ◽  
Construction Materials ◽  
Reference Value ◽  
Physical And Mechanical Properties ◽  
Road Construction ◽  
Experimental Methods ◽  
Frost Heaving ◽  
The World ◽  
Rock And Soil

In many areas, there are still a development road construction materials, traditionally, often use reinforced concrete, asphalt and other adhesive method to strengthen the low strength of rock and soil anti-freeze expansion coefficient; And now all countries in the world are studying how to use industrial production waste development of new composite materials. One of the most development potential, the production of industrial waste - slime. This paper USES the Russian kazan national construction university experimental methods, in the experiment to improve frost heaving soil physical and mechanical properties of the method for the synthesis of adhesive, based on the feasibility and applicability, environmental assessment of research and analysis, for the use of adhesive put forward a lot of reference value.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

scholarly journals Mechanical and structural properties of composites made from recycled and virgin polyethylene terephthalate (PET) and metal chip or mesh wire

2019 ◽  
Vol 299 ◽  
pp. 06007
Author(s):  
Mircea Aurelian Antoniu Rusu ◽  
Sever-Adrian Radu ◽  
Catalin Moldovan ◽  
Codruta Sarosi ◽  
Ionela Amalia Mazilu (Moldovan) ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polyethylene Terephthalate ◽  
Processing Parameters ◽  
Sem Images ◽  
Major Drawback ◽  
Recycled Pet ◽  
Plastic Processing ◽  
Metal Chip ◽  
Intense Research ◽  
Properties Of Composites

Although polyethylene terephthalate (PET) is a champion of recycling, intense research is being done to find new solutions for using recycled plastic. This study aims to characterize the mechanical andstructural properties (SEM- scanning electron microscopy) of products made from recycled metal swarf or mesh wire with recycled plastic (PET) in comparison with virgin plastic. Samples manufactured from virgin and recycled PET are made by pressing and high temperature. The loss of mechanical properties ofproducts made from recycled plastic is a major drawback that influences their use. SEM images confirm that the dispersion and distribution of the PET phase is not very uniform. By addition of virgin plastic in various compositions with recycled plastic, processing parameters and mechanical properties can be optimized.

Role of Interfacial Interactions on Mechanical Properties of Biomimetic Composites for Bone Tissue Engineering

2005 ◽  
Vol 898 ◽  
Author(s):  
Devendra Verma ◽  
Rahul Bhowmik ◽  
Bedabibhas Mohanty ◽  
Dinesh R Katti ◽  
Kalpana S Katti
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Mechanical Response ◽  
Density Ratio ◽  
Interfacial Interactions ◽  
Porous Composites ◽  
Properties Of Composites

AbstractInterfaces play an important role in controlling the mechanical properties of composites. Optimum mechanical strength of scaffolds is of prime importance for bone tissue engineering. In the present work, molecular dynamics simulations and experimental studies have been conducted to study effect of interfacial interactions on mechanical properties of composites for bone replacement. In order to mimic biological processes, hydroxyapatite (HAP) is mineralized in presence of polyacrylic acid (PAAc) (in situ HAP). Further, solid and porous composites of in situ HAP with polycaprolactone (PCL) are made. Mechanical tests of composites of in situ HAP with PAAc have shown improved strain recovery, higher modulus/density ratio and also improved mechanical response in simulated body fluid (SBF). Simulation studies indicate potential for calcium bridging between –COO− of PAAc and surface calcium of HAP. This fact is also supported by infrared spectroscopic studies. PAAc modified surfaces of in situ HAP offer means to control the microstructure and mechanical response of porous composites. Nanoindentation experiments indicate that apatite grown on in situ HAP/PCL composites from SBF has improved elastic modulus and hardness. This work gives insight into the interfacial mechanisms responsible for mechanical response as well as bioactivity in biomaterials.

Optimizing the Shape and Size of Cruciform Specimens Used for Biaxial Tensile Test

2014 ◽  
Vol 658 ◽  
pp. 167-172 ◽  
Author(s):  
Liviu Andrusca ◽  
Viorel Goanta ◽  
Paul Doru Barsanescu
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Continuous Monitoring ◽  
Biaxial Tension ◽  
Cruciform Specimen ◽  
Testing Method ◽  
Biaxial Tests ◽  
Properties Of Materials ◽  
Failure Theories ◽  
Shape And Size

Testing cruciform specimens subjected to biaxial tension is one of the most widely used experimental techniques and more accurate at this time to determine the mechanical properties of materials and to verify the failure theories. This type of experiment allows the continuous monitoring of behavior of materials from the beginning of deformation until fracture under different ratios of forces and directions of the deformation, which transforms it into a very versatile testing method. We have varied the number of parameters and their values in order to achieve a uniform distribution of biaxial state of stresses and strains in the area tested. In theory, any material can be tested by stretching a biaxial cruciform specimen, but must be investigated in what way the shape of the specimen influence the data obtained. In this paper are presented the requirements that must be fulfilled by the samples used for tensile / compression biaxial tests and the design of cruciform specimens through FEA that meet these demands.

Mechanical Properties of SiO2 vs. SiO2-TiO2 Bulk Glasses and Fibers

1991 ◽  
Vol 244 ◽  
Author(s):  
Suresh T. Gulati
Keyword(s):  
Mechanical Properties ◽  
Optical Fibers ◽  
Mechanical Performance ◽  
Fatigue Behavior ◽  
Deformation Mode ◽  
Strength Distribution ◽  
Fused Silica ◽  
Space Applications ◽  
Silica Glasses ◽  
Silica And Titania

ABSTRACTThe mechanical properties of silica and titania-doped silica glasses, in bulk and fiber forms, are presented. These include the elastic properties (E and ν), strength distribution (in tension and bending), fatigue behavior (dynamic and static loading) and fracture toughness. Following a brief review of above properties for fused silica and ULE™ glasses (Coming Codes 7940 and 7971), used primarily for space applications, the mechanical properties data for silica and titania-doped silica-clad optical fibers are presented. The enhancement of mechanical performance of titania-doped silica clad fiber is also discussed.The effect of titania doping on fundamental properties like stress-free activation energy, crack tip pH, and deformation mode of Si-O-Si bond is discussed. In addition, the crack velocity data obtained from DCDC specimens of homogeneous silica and titania-doped silica glasses are compared in an attempt to understand the role titania plays in improving the fatigue resistance of optical fibers.

Sign in / Sign up

Export Citation Format

Share Document