Wear Resistance of NiCoCrAlY Alloy Coating by Cold Spraying

2014 ◽  
Vol 898 ◽  
pp. 47-50
Author(s):  
Sheng Qiang Feng ◽  
Bing Ma ◽  
Xiu Ling Wang ◽  
Lang Cui ◽  
Guang Liu ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Magnesium Alloy ◽  
Abrasive Wear ◽  
Adhesive Wear ◽  
Cold Spraying ◽  
Alloy Coating ◽  
Corrosive Wear ◽  
Fatigue Wear ◽  
Wear Mode ◽  
Wear Modes

NiCoCrAlY coating with high density was prepared on the surface of the magnesium alloy by cold spraying. Compared with the magnesium alloy prepared by the methods of the semi-continuous casting, the wear resistance and wear mode were analyzed by the experiments. The results showed that, under the dry friction condition, the conditions of the weightlessness of wear of NiCoCrAlY coating were better than that of the magnesium alloy. After the frictional experiment for 20 minutes, the weightlessness of wear of NiCoCrAlY coating was 10mg. Compared with that of the magnesium alloy, the weightlessness of wear was lower than 28%. Consequently, the NiCoCrAlY coating had the capacity of the weightlessness of wear resistance. By the comparisons of the every samples friction morphology, the wear modes of the NiCoCrAlY coating were adhesive wear and abrasive wear. And the wear modes of magnesium alloy were also adhesive wear and abrasive wear with corrosive wear and fatigue wear.

scholarly journals Microstructure and Properties of Cold Sprayed NiCrAl Coating on AZ91D Magnesium Alloy

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 193
Author(s):  
Xiangwei Zhao ◽  
Tianshun Dong ◽  
Binguo Fu ◽  
Guolu Li ◽  
Qi Liu ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Cold Spraying ◽  
Corrosion Current ◽  
Wear Volume ◽  
Fatigue Wear ◽  
Az91d Magnesium Alloy ◽  
Superior Corrosion Resistance ◽  
Plasma Sprayed

Herein, a NiCrAl coating was prepared on the AZ91D magnesium alloy by cold spraying technology. The microstructure, wear resistance, and corrosion resistance of the cold sprayed NiCrAl coating were studied and compared with two NiCrAl coatings prepared by plasma spraying. The results showed that the porosity of the two-plasma sprayed NiCrAl coatings was 3.21% and 2.66%, respectively, while that of the cold sprayed NiCrAl coating was only 0.68%. The hardness of the cold sprayed NiCrAl coating (650 HV0.1) was higher than those of the two-plasma sprayed NiCrAl coatings (300 HV0.1, 400 HV0.1). In the abrasion resistance test, the cold sprayed NiCrAl coating showed a lower friction coefficient (0.346), less wear volume (3.026 mm3), and superior wear resistance accordingly compared with the two-plasma sprayed NiCrAl coatings. Moreover, the scanning electron microscopy (SEM) morphology at the bottom of the wear trace of the cold sprayed NiCrAl coating showed a compact mechanically mixed layers (MML) structure, and its wear mechanism was mainly abrasive wear, with some fatigue wear. In the electrochemical test, the corrosion current density of the cold sprayed NiCrAl coating (4.404 × 10−2 A·cm−2) was much lower than those of two plasma sprayed coatings (25.96 A·cm−2, 26.98 A·cm−2), indicating that the cold sprayed NiCrAl coating had superior corrosion resistance. Therefore, preparing a cold sprayed NiCrAl coating is a feasible method to comprehensively improve the wear resistance and corrosion resistance of the AZ91D magnesium alloy.

Microstructure and Tribological Properties of Stellite21 Coating by Electro-Spark Deposition

2013 ◽  
Vol 423-426 ◽  
pp. 939-943 ◽  
Author(s):  
Qi Feng Jing ◽  
Ye Fa Tan ◽  
Hui Yong Ji ◽  
Xiao Long Wang ◽  
Li Gao ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Phase Composition ◽  
Abrasive Wear ◽  
Tribological Properties ◽  
Wear Mechanism ◽  
Alloy Coating ◽  
Fatigue Wear ◽  
Compact Structure

Setellite21 cobalt-based alloy coating was deposited on 45 steel by electro-spark deposition. Microstructure and phase composition of the coating were analyzed. Wear resistance and wear mechanism of the coating were researched. The results indicate that the coating with compact structure is mainly composed of Co, Co6W6C, CoCx and CoCr. Average microhardness of the coating is 445.34 HV0.5, which is about 2 times to that of the substrate. The coating presents excellent wear resistance with no obvious peelings and scratches. Wear resistance of the coating is about 2.3~2.7 times to that of the substrate. Wear mechanism of the coating mainly contains abrasive wear and fatigue wear, and along with oxidization wear.

Corrosive-wear behavior of LSP/MAO treated magnesium alloys in physiological environment with three pH values

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Yongshui Shen ◽  
Tongjin Sun ◽  
Tao Zhu ◽  
Ying Xiong
Keyword(s):  
Abrasive Wear ◽  
Wear Mechanisms ◽  
Adhesive Wear ◽  
Laser Shock ◽  
Corrosion Wear ◽  
Fatigue Wear ◽  
Wear Rates ◽  
Ph Values ◽  
Wear And Corrosion ◽  
Micro Arc Oxidation

Abstract A laser shock peening (LSP) layer, a micro-arc oxidation (MAO) coating, and an LSP/MAO composite coating were fabricated on the surface of AZ80 magnesium alloy by laser shock and micro-arc oxidation process. The ball-disc grinding method was used to perform wear test on the three treated specimens in simulated body fluids (SBF) with pH values of 4, 7.4 and 9. The morphology and element content of worn surface were investigated by scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). The results indicated that the wear rates of the three treated specimens in three pH environment in numerical order were pH 4 > pH 7.4 > pH 9, respectively. The wear rates of the three treated specimens in the same pH environment were arranged in the order of MAO > LSP > LSP/MAO, respectively. The main wear mechanisms of the LSP specimen in pH 4 environment were fatigue wear and corrosion wear, while it were corrosion wear and adhesive wear in pH 7.4 and pH 9 environments. Abrasive wear, fatigue wear and corrosion wear were the main wear mechanisms of the MAO specimen in pH 4 environment, while abrasive wear, adhesive wear and corrosion wear were the main wear mechanisms of that in pH 7.4 and pH 9 environments. The corrosion wear resistance of the LSP/MAO specimen in SBF solution with three pH values was improved due to the synergism of LSP fine crystal layer and MAO coating.

Effect of Nano Sodium Titanate/ Potassium Titanate Whisker on Tribology Behavior of Brake Materials

2020 ◽  
Vol 993 ◽  
pp. 836-843
Author(s):  
Ke Guo ◽  
Zhi Qiang Zhang ◽  
Zhong Zheng Pei ◽  
Jie Xu ◽  
Yi Fan Feng
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Abrasive Wear ◽  
Wear Mechanisms ◽  
Adhesive Wear ◽  
Sodium Titanate ◽  
Brake Pad ◽  
Potassium Titanate

Here we developed a hot-pressed molded resin-based brake pad material reinforced by a nano sodium titanate whisker in comparison with nano potassium titanate whisker. The effect of the whiskers on the tribology behavior was investigated. Though nano sodium titanate whisker reinforced brake material showed higher porosity (+12.29% averagely) and lower hardness (-25.8% averagely) caused by the impurities, it exhibited improved ability in stabilizing the friction coefficient and enhancing 25.5%, 31.1%, 25.9% higher wear resistance, when the volume contents of whisker are 7.5%, 15% and 22.5%, respectively, compared to the nano potassium titanate whisker reinforced brake material. The wear mechanisms of the nano sodium titanate whisker reinforced brake materials were determined as embedded debris, delaminated crater, moderate layers transfer, uniform furrows, primary plateaus and secondary plateaus in similar size, indicating a main wear form of abrasive wear instead of adhesive wear.

Corrosive wear and electrochemical corrosion behaviors of laser thermal sprayed CoCrAlYTaSi coatings in 3.5 Wt.% NaCl solution

2019 ◽  
Vol 66 (5) ◽  
pp. 537-543 ◽  
Author(s):  
Zhou Weitong ◽  
Kong Dejun
Keyword(s):  
Abrasive Wear ◽  
Chemical Elements ◽  
Electrochemical Corrosion ◽  
Alloy Coating ◽  
Corrosive Wear ◽  
Charge Transfer Resistance ◽  
Nacl Solution ◽  
Transfer Resistance ◽  
Content Type ◽  
Wear Rates

Purpose This paper aims to enhance the corrosive wear and electrochemical corrosion of Ti–6Al–4V alloy. Design/methodology/approach A CoCrAlYTaSi alloy coating was fabricated on Ti–6Al–4V alloy using a laser thermal spraying (LTS). The surface and cross-section morphologies, chemical elements, phases and bonding strength of the obtained coating were analyzed using a scanning electron microscope, energy dispersive spectroscope, X-ray diffraction and scratch test, respectively, The corrosive wear and electrochemical corrosion of CoCrAlYTaSi coating in 3.5 Wt.% NaCl solution were investigated using a wear tester and electrochemical workstation, respectively. Findings The average coefficient of frictions (COFs) of CoCrAlYTaSi coating under the wear loads of 2, 4 and 6 N are 1.31, 1.02 and 0.88, respectively; and the corresponding wear rates are 0.66 × 10−4, 1.10 × 10−4 and 1.30 × 10−4 mm3·N–1·m–1, respectively. The wear mechanism under the wear load of 2 N is abrasive wear, while those under the wear loads of 4 and 6 N are adhesive wear and abrasive wear. The charge transfer resistance of CoCrAlYTaSi coating is 5.368 × 105 Ω·cm2, higher than 2.193 × 105 of the substrate. Originality/value In this study, a CoCrAlYTaSi coating was firstly fabricated on Ti–6Al–4V alloy using a LTS. Its corrosive wear and electrochemical corrosion in 3.5 Wt.% NaCl solution were investigated, which played a protective role of corrosive wear on Ti–6Al–4V alloy.

Progressive Tool Failure in High Speed End Milling of Inconel 718 with Coated Carbide Inserts

2011 ◽  
Vol 188 ◽  
pp. 32-37 ◽  
Author(s):  
An Hai Li ◽  
Jun Zhao ◽  
Z.Q. Pei ◽  
S.G. Guo
Keyword(s):  
Abrasive Wear ◽  
Inconel 718 ◽  
Adhesive Wear ◽  
End Milling ◽  
Failure Mechanisms ◽  
Cutting Speed ◽  
Fatigue Wear ◽  
Edge Chipping ◽  
Tool Failure ◽  
Coated Carbide

The failure progression of coated carbide tools in end milling of Inconel 718 superalloy was investigated. Tool wear was measured and failure mechanisms were discussed in the experimental process periodically. The experimental results indicated that the tool failure mechanisms were synergistic interaction among abrasive wear, adhesive wear, and fatigue wear. However, abrasive wear and adhesive wear were the main failure mechanisms at the beginning, fatigue wear prevailed the upper hand around the time when edge chipping appeared, and after edge chipping abrasive wear and adhesive wear dominated until the failure time. In addition, the macroscopic failure of the cutting tools is closely correlated to the nucleation and propagation of the crack under cyclic mechanical and thermal impact forces. Mechanical fatigue wear was the key form of fatigue wear at lower cutting speed, while at higher cutting speed thermal fatigue wear was the dominant fatigue wear.

scholarly journals Wear Resistance of High C High Si Steel with Low Retained Austenite Content and Kinetically Activated Bainite

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 672 ◽  
Author(s):  
Bojan Podgornik ◽  
Mihael Brunčko ◽  
Peter Kirbiš
Keyword(s):  
Wear Resistance ◽  
Retained Austenite ◽  
Adhesive Wear ◽  
Cold Work ◽  
High Hardness ◽  
Bearing Steel ◽  
Austenite Content ◽  
Surrounding Matrix ◽  
Aisi D2 ◽  
Wear Mode

A novel high C high Si carbide free bainitic steel was developed for the production of cold work tools, knives, and rolls, requiring high hardness, toughness, as well as abrasive/adhesive wear resistance and resistance to galling at low costs. The steel was tribologically tested in dry sliding conditions under abrasive and adhesive wear mode, facilitated by using alumina and bearing steel ball as a counter-material, respectively. It was determined that carbide dissolution occurs under high contact pressures, thereby enriching the surrounding matrix with carbon and locally increasing the retained austenite content. The high retained austenite at the sliding interface increases the steels work hardening capacity and promotes superior wear resistance when compared to much more alloyed cold work tool steel, such as AISI D2. The steel has a high resistance to galling as determined by sliding against a soft steel bar due to its chemical composition.

Research on the Structure and Wear Properties of Grind-Hardened 42CrMo

2012 ◽  
Vol 619 ◽  
pp. 561-566 ◽  
Author(s):  
Lian Yong Zhang ◽  
Fang Hong Sun ◽  
Yan Hua Jiang
Keyword(s):  
Wear Resistance ◽  
Abrasive Wear ◽  
Adhesive Wear ◽  
Lath Martensite ◽  
Hardened Layer ◽  
Wear Properties ◽  
42Crmo Steel ◽  
Grind Hardening

grind-hardening test was performed on 42CrMo steel in the paper. Microstructure of the hardened layer was observed and the wear-resistance of hardened specimens was done too. The results showed that microstructure of the fully hardened layer was mainly composed by lath martensite; microhardness of the hardened layer was above 700HV and the abrasive wear and the adhesive wear properties of hardened layer were 2~9 times than that of the base.

Influence of Neodymium on Wear Resistance of Hypereutectic Al-Si Alloy

2015 ◽  
Vol 1095 ◽  
pp. 135-139
Author(s):  
Wei Xi Shi ◽  
Cheng Wu Du ◽  
Gui Mao Li ◽  
Zhi Ming Liu
Keyword(s):  
Wear Resistance ◽  
Abrasive Wear ◽  
Wear Mechanism ◽  
Friction And Wear ◽  
Adhesive Wear ◽  
Primary Silicon ◽  
Oxidative Wear ◽  
Initial Sample ◽  
Unmodified Alloy ◽  
Resistance Tests

The morphology of eutectic and primary silicon phases was analyzed by OM and SEM. OM and SEM results show that pure Nd can significantly refine both eutectic and primary silicon of hypereutectic Al-20%Si alloy. Morphology of primary silicon is transformed from star-shaped and irregular morphology to fine polyhedral and grain size of primary silicon is refined from 80~120 μm to 20~50 μm. Friction and wear resistance tests show that friction coefficient of Al-20%Si alloy reduces after Nd modification. Wear resistance of Al-20%Si alloy after modification is significantly improved as compared to the initial sample. The dominant wear mechanism for 0.3% Nd modified alloy is abrasive wear, adhesive wear and oxidative wear mechanism, but wear mechanism for unmodified alloy is abrasive wear and adhesive wear mechanism.

Sign in / Sign up

Export Citation Format

Share Document