Effects of Pretreatment Methods on the Enamel Surface Improving Sealant Adhesion

2019 ◽  
Vol 40 ◽  
pp. 92-100
Author(s):  
Adina Rotaru-Birgaoanu ◽  
Teodora Teslaru ◽  
R. Ionut Olariu ◽  
Ionut Chirap ◽  
Liliana Sachelarie ◽  
...  
Keyword(s):  
Atmospheric Pressure ◽  
Diffuse Reflectance ◽  
Enamel Surface ◽  
Acid Etching ◽  
Minimum Level ◽  
Angle Measurements ◽  
Physical Chemical ◽  
Contact Angle Measurements ◽  
Hydrophilic Character ◽  
Yellow Index

Is PlasBeam pretreatment an efficient method to improve sealant adhesion onto the enamel surface?The aim of this study isto investigate the effects induced by three pretreatment techniques used to improve sealant adhesion on the enamel surface, respectively standard acid-etching, UV radiations and a new method based on plasma operating at atmospheric pressure, namely the PlasBeam method.The physical-chemical modifications induced onto the enamel surface by the above pretreatments were analyzed using Contact Angle Measurements and Diffuse Reflectance Spectroscopy.The changes in the enamel surface morphology show that the acid-etching pretreatment is mostly efficient in increasing roughness, but this method stimulates the degradation processes that are well-known and turns down the brillianceof the treated surface. On the other hand, the PlasBeam treatment brings a higher roughness at the contact area between sealant and the enamel surface, compared to the UV radiations pretreatments.Moreover, the PlasBeam improves the hydrophilic character of enamel as a practical solution in enhancing the sealant adhesion to the surface. Related to other effects, it has been noticed that thePlasBeam method generates the most reflective enamel surface, whereas the White/Yellow index reaches the minimum level after a 10 second treatment.

scholarly journals Improved de-inking of inkjet-printed paper using environmentally friendly atmospheric pressure low temperature plasma for paper recycling

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Rodolphe Mauchauffé ◽  
Seung Jun Lee ◽  
Isaac Han ◽  
Sang Hyeong Kim ◽  
Se Youn Moon
Keyword(s):  
Plasma Treatment ◽  
Atmospheric Pressure ◽  
Paper Recycling ◽  
Temperature Plasma ◽  
Water Contact ◽  
Angle Measurements ◽  
Natural Energy ◽  
Contact Angle Measurements ◽  
Speed Up ◽  
Uv Visible

Abstract Nowadays, due to environmental pollution and natural energy consumption caused by waste paper, many researches are being conducted on the reuse of printed-paper. To recycle the paper, de-inking has to be performed. In this article, in order to reduce the use of the commonly used de-inking chemicals, the effect of an atmospheric pressure helium plasma treatment on the de-inking enhancement of printed-paper is studied. Through colorimeter and UV-visible spectrometer measurements the plasma treatment is shown to speed up the de-inking. While SEM observations and FTIR measurements suggest that the paper quality is retained upon plasma treatment, the increase of surface hydrophilicity measured by water contact angle measurements, compared to non-treated paper, is believed to enhance the fiber swelling of the paper and lead to a faster ink removal.

Antimicrobial Coatings Obtained in an Atmospheric Pressure Dielectric Barrier Glow Discharge

2002 ◽  
Vol 724 ◽  
Author(s):  
Sabine Paulussen ◽  
Dirk Vangeneugden ◽  
Olivier Goossens ◽  
Erik Dekempeneer
Keyword(s):  
Glow Discharge ◽  
Atmospheric Pressure ◽  
Bacterial Colonization ◽  
Polymer Coatings ◽  
Plasma Polymer ◽  
Antimicrobial Coatings ◽  
Dielectric Barrier ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Thin Plasma

AbstractThis paper addresses the development of plasma polymer coatings that should prevent bacteria from adhering to medical devices, implants, textile fibers, packaging materials, etc. The two main parameters affecting bacterial colonization onto surfaces are the surface energy and the surface roughness. Both parameters can be adjusted by the deposition of a thin plasma polymer coating in an atmospheric pressure dielectric barrier glow discharge. According to SEM, FTIR, SPM, XPS and contact angle measurements, smooth, hydrophilic plasma polymer coatings were obtained under specific plasma conditions starting from 2-hydroxyethyl methacrylate (HEMA) and ethyl diazoacetate (EDA).

scholarly journals Surface Characterisation of PEEK and Dentin, Treated with Atmospheric Non-Thermal PDD Plasma, Applicable for Dental Chair-Side Procedures

Plasma ◽  
2021 ◽  
Vol 4 (3) ◽  
pp. 389-398
Author(s):  
Marius Behnecke ◽  
Vincent Steinert ◽  
Svea Petersen
Keyword(s):  
Contact Angle ◽  
Phosphoric Acid ◽  
Plasma Treatment ◽  
Water Contact Angle ◽  
Acid Etching ◽  
Water Contact ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Dentin Tubules ◽  
Phosphoric Acid Etching

This study investigates the suitability of Piezoelectric Direct Discharge Plasma as a tool for wetting behaviour modification of PEEK and dentin, and compares the results of this method with low-pressure plasma treatment and phosphoric acid etching. Static contact angle measurements were made, roughness was assessed using tactile measurement, and AFM and SEM images were taken. An optimum operating distance of ≤15 mm was determined for the plasma based on the water contact angle. Furthermore, it was demonstrated that despite only a fraction of the power, the PDD plasma also produces hydrophilic and nanostructured PEEK surfaces with a 38° water contact angle in the same plasma time. In contrast, the gold standard of dental surface modification of dentin—phosphoric acid etching—showed no measurable contact angle due to the exposed dentin tubules. Treatment with PDD plasma reduces the water contact angle of dentin from 65° to 43° and is not negative affected by water. Wet, PDD plasma-treated dentin samples show a water contact angle of only 26.5°. The dentin tubules exposed by chemical etching led to a significantly increased roughness. No comparable effect could be demonstrated for plasma treatment on dentin, but based on the contact angle measurements, a chemically strongly activated surface with strongly polar interaction behaviour can be assumed. The additional use of the PDD plasma technique to improve wetting could therefore have a positive effect on the adhesive bond between human dentin and polymeric dental restorative materials or, depending on the adhesive system, replace the etching process altogether.

scholarly journals Assessment of Wettability and Contact Angle of Bonding Agent with Enamel Surface Etched by Five Commercially Available Etchants: An In Vitro Study

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Deepika Katyal ◽  
Aravind Kumar Subramanian ◽  
Adith Venugopal ◽  
Anand Marya
Keyword(s):  
Contact Angle ◽  
Statistical Analysis ◽  
In Vitro Study ◽  
Enamel Surface ◽  
Bonding Agent ◽  
Etch Pattern ◽  
Angle Measurements ◽  
Significant Difference ◽  
Contact Angle Measurements

Background. The quantity and quality of the etching pattern produced by acids play a significant role in the wettability and contact angle of the adhesive with the enamel surface in orthodontics. The better the etch pattern, the more the surface energy of the enamel, better the penetration of the adhesive, which ultimately results in better bond strength. The present study aimed to evaluate the contact angle of the bonding agent with the enamel surface etched by five commercially available etchants and check if any difference existed between the five. Materials and Methods. Twenty-five human maxillary and mandibular central incisors and premolars extracted for orthodontic or dental purposes were used in this study as samples. The teeth were allocated into five groups based upon the etchant used to etch the enamel surface. After the samples were etched, a hard tissue microtome was used to create thin slices of the enamel surface. The samples were then exposed to bonding agent Ormco Enlight. The bonding agent was released in the form of droplets onto the enamel slices mounted on a contact angle goniometer. The contact angle values were tabulated, and statistical analysis using the one-way ANOVA test was carried out. Results. The contact angle measurements of the etchant group, DPI, were the lowest, while D-tech has the highest contact angle values. However, statistical analysis revealed no statistically significant difference between the contact angle measurements of the five groups included in the study. Conclusion. No statistically significant difference existed between the five etchant groups included in the study. However, commercially available etchant DPI showed lesser contact angle and thus better wettability in comparison to other groups. Further elemental analysis and surface analysis are required to validate these results.

Size-dependence hydrophobicity in nanocrystalline talc produced by high-intensity planetary ball milling

2015 ◽  
Vol 1805 ◽  
Author(s):  
Rebeca Caban-Nevarez ◽  
Oscar J Perales Perez
Keyword(s):  
Particle Size ◽  
High Intensity ◽  
Ball Mill ◽  
Size Dependence ◽  
Particle Size Reduction ◽  
Angle Measurements ◽  
Micron Size ◽  
Contact Angle Measurements ◽  
Planetary Ball Milling ◽  
Hydrophilic Character

ABSTRACTMicron-size talc samples were ground using a high-intensity planetary ball mill at different milling times as an attempt to reduce particle size and study the effect on the corresponding hydrophobicity. XRD and SEM results confirmed the decrease in the particle size. FTIR spectroscopy analyses revealed the talc characteristic bands centered on 669 cm-1 for the O-H bonds and 1018 cm-1 for the Si-O bonds, as well as a degradation in the talc structure for prolonged milling times. BET results indicate an increase of specific surface area, which also confirms particle size reduction, reaching a maximum at 1 h, after which the particles agglomerate. Contact angle measurements show a decrease in the hydrophobicity of talc after milling. Although talc retains its hydrophobicity after short milling periods, prolonged grinding causes the mineral to have a more hydrophilic character.

Nanostructured Polymer Brushes With Reversibly Changing Properties

2002 ◽  
Vol 727 ◽  
Author(s):  
Denys Usov ◽  
Manfred Stamm ◽  
Sergiy Minko ◽  
Christian Froeck ◽  
Andreas Scholl ◽  
...  
Keyword(s):  
Polymer Brushes ◽  
Phase Segregation ◽  
Water Contact ◽  
Angle Measurements ◽  
Nanostructured Polymer ◽  
Contact Angle Measurements ◽  
Vertical Segregation ◽  
Oxygen Plasma Etching ◽  
Grafting From ◽  
Photoemission Electron

AbstractWe investigated the interplay between different mechanisms of the lateral and vertical segregation in the synthesized via “grafting from” approach symmetric A/B (where A and B are poly(styrene-co-2,3,4,5,6-pentafluorostyrene) and poly(methylmethacrylate), respectively) polymer brushes upon exposure to different solvents. We used X-ray photoemission electron spectroscopy and microscopy (X-PEEM), AFM, water contact angle measurements, and oxygen plasma etching to study morphology of the brushes. The ripple morphology after toluene (nonselective solvent) revealed elongated lamellar-like domains of A and B polymers alternating across the surface. The dimple-A morphology consisting of round clusters of the polymer A was observed after acetone (selective solvent for B). The top layer was enriched with the polymer B showing that the brush underwent both the lateral and vertical phase segregation. A qualitative agreement with predictions of SCF theory was found.

Wrinkling Poly(trimethylene 2,5-Furanoate) Free-standing Films: Nanostructure Formation and Physical Properties

2020 ◽  
Author(s):  
Michelina Soccio ◽  
Nadia Lotti ◽  
Andrea Munari ◽  
Esther Rebollar ◽  
Daniel E Martínez-Tong
Keyword(s):  
Irradiation Time ◽  
Polymer Surface ◽  
Laser Source ◽  
Free Standing ◽  
Force Microscopy ◽  
Nanostructure Formation ◽  
Physicochemical Changes ◽  
Angle Measurements ◽  
Atomic Force ◽  
Contact Angle Measurements

<p>Nanostructured wrinkles were developed on fully bio-based poly(trimethylene furanoate) (PTF) films by using the technique of Laser Induced Periodic Surface Structures (LIPSS). We investigated the effect of irradiation time on wrinkle formation using an UV pulsed laser source, at a fluence of 8 mJ/cm2. It was found that the pulse range between 600 and 4800 pulses allowed formation of periodic nanometric ripples. The nanostructured surface was studied using a combined macro- and nanoscale approach. We evaluated possible physicochemical changes taking place on the polymer surface after irradiation by infrared spectroscopy, contact angle measurements and atomic force microscopy. The macroscopic physicochemical properties of PTF showed almost no changes after nanostructure formation, differently from the results previously found for the terephthalic counterparts, as poly(ethyleneterephthalate), PET, and poly(trimethyleneterephthalate), PTT. The surface mechanical properties of the nanostructured PTF were found to be improved, as evidenced by nanomechanical force spectroscopy measurements. In particular, an increased Young’s modulus and higher stiffness for the nanostructured sample were measured. <br></p>

scholarly journals Adhesion Studies during Generative Hybridization of Textile-Reinforced Thermoplastic Composites via Additive Manufacturing

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3888
Author(s):  
Johanna Maier ◽  
Christian Vogel ◽  
Tobias Lebelt ◽  
Vinzenz Geske ◽  
Thomas Behnisch ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Polyamide 6 ◽  
Thermoplastic Composites ◽  
Efficient Production ◽  
Angle Measurements ◽  
Small Series ◽  
Contact Angle Measurements ◽  
Static Tensile ◽  
Pre Treatment ◽  
Manufacturing Technologies

Generative hybridization enables the efficient production of lightweight structures by combining classic manufacturing processes with additive manufacturing technologies. This type of functionalization process allows components with high geometric complexity and high mechanical properties to be produced efficiently in small series without the need for additional molds. In this study, hybrid specimens were generated by additively depositing PA6 (polyamide 6) via fused layer modeling (FLM) onto continuous woven fiber GF/PA6 (glass fiber/polyamide 6) flat preforms. Specifically, the effects of surface pre-treatment and process-induced surface interactions were investigated using optical microscopy for contact angle measurements as well as laser profilometry and thermal analytics. The bonding characteristic at the interface was evaluated via quasi-static tensile pull-off tests. Results indicate that both the bond strength and corresponding failure type vary with pre-treatment settings and process parameters during generative hybridization. It is shown that both the base substrate temperature and the FLM nozzle distance have a significant influence on the adhesive tensile strength. In particular, it can be seen that surface activation by plasma can significantly improve the specific adhesion in generative hybridization.

scholarly journals Epoxy/alumina composite coating on welded steel 316L with excellent wear and anticorrosion properties

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Maryama Hammi ◽  
Younes Ziat ◽  
Zakaryaa Zarhri ◽  
Charaf Laghlimi ◽  
Abdelaziz Moutcine
Keyword(s):  
Electrochemical Behaviour ◽  
Sem Analysis ◽  
Water Contact ◽  
Welded Steel ◽  
Melted Zone ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Alumina Composite ◽  
The Cost ◽  
Good Contrast

AbstractThe main purpose of this study is to elaborate anticorrosive coatings for the welded steel 316L, since this later is widely used in industrial field. Hence, within this work we have studied the electrochemical behaviour of different zones of the welded steel 316 in 1 M HCl media. The macrography study of the welded steel has revealed the different areas with a good contrast. We have stated three different zones, namely; melted zone (MZ), heat affected zone (HAZ) and base metal zone (BM). Impedance studies on welded steel 316L were conducted in 1 M HCl solution, coating of Epoxy/Alumina composite was applied on different zones, in order to reveal the anti-corrosion efficiency in each zone. Scanning electron microscopy (SEM) analysis was undertaken in order to check how far the used coating in such aggressive media protects the studied zones and these findings were assessed by water contact angle measurements. The choice of this coating is based on the cost and the safety. We concluded that the Epoxy/Alumina composite has a good protecting effect regarding welded steel in aggressive media.

Sign in / Sign up

Export Citation Format

Share Document