Sol-Gel Process and Properties of Textured Pb(Zr, Ti)O3 Films on Silicon Wafers

2007 ◽  
Vol 280-283 ◽  
pp. 239-242 ◽  
Author(s):  
Wen Gong ◽  
Xiang Cheng Chu ◽  
Jing Feng Li ◽  
Zhi Lun Gui ◽  
Long Tu Li
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Sol Gel ◽  
Lead Zirconate ◽  
Silicon Wafers ◽  
Seeding Layer ◽  
Pzt Thin Films ◽  
Pzt Film ◽  
Sol Gel Process ◽  
Pzt Films

Lead zirconate titanate (PZT) thin films with a composition near the morphotropic phase boundary were deposited on silicon wafers by using a modified sol-gel method. Introducing a seeding layer between the interface of PZT film and platinum electrode controlled the texture of PZT films. The lead oxide seeding layer results in highly (001)-textured PZT film, while the titanium dioxide seeding layer results in (111)-textured one. SEM and XRD were used to characterize the PZT thin films. The ferroelectric and piezoelectric properties of the PZT films were evaluated and discussed in association with different preferential orientations.

Fabrication of Thick, Sol Gel Pzt Films: Applications to Macroscopic Piezoelectric Devices

1994 ◽  
Vol 360 ◽  
Author(s):  
D.A. Barrow ◽  
T.E. Petroff ◽  
M. Sayer
Keyword(s):  
Lead Zirconate Titanate ◽  
Sol Gel ◽  
Low Frequency ◽  
Lead Zirconate ◽  
Resonant Vibrations ◽  
Pzt Film ◽  
Sol Gel Process ◽  
Pzt Films ◽  
High Frequency Resonance ◽  
Piezoelectric Devices

AbstractLead zirconate titanate (PZT) films of up to 60 μm in thickness have been fabricated on a wide variety of substrates using a new sol gel process. The dielectric properties (∈ = 900), ferroelectric (Ec = 16 kV/cm and Pr = 35 μC/cm 2) and piezoelectric properties are comparable to bulk values. The characteristic Curie point of these films is at 420 °C. Piezoelectric actuators have been developed by depositing thick PZT films on both planar and coaxial substrates. Stainless steel cantilevers and optical fibres coated with a PZT film exhibit flexure mode resonant vibrations observable with the naked eye. A low frequency in-line fibre optic modulator has been developed using a PZT coated optical fibre. The high frequency resonance of a 60 μm film on a aluminum substrate has been observed.

EFFECT OF PRE-HEATING TEMPERATURE ON THE CHARACTERISTICS OF PZT THIN FILMS GROWN BY USING A TRIOL SOL–GEL ROUTE

2007 ◽  
Vol 14 (02) ◽  
pp. 229-234
Author(s):  
SARAWUT THOUNTOM ◽  
MANOCH NAKSATA ◽  
KENNETH MACKENZIE ◽  
TAWEE TUNKASIRI
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Heating Temperature ◽  
Ferroelectric Properties ◽  
Sol Gel ◽  
Hysteresis Loops ◽  
Lead Zirconate ◽  
Pzt Thin Films ◽  
Pzt Films ◽  
Ferroelectric Hysteresis

Lead zirconate titanate (PZT) films with compositions near the morphotropic phase boundary were fabricated on Pt (111)/ Ti / SiO 2/ Si (100) using the triol sol–gel method. The effect of the pre-heating temperature on the phase transformations, microstructures, electrical properties, and ferroelectric properties of the PZT thin films was investigated. Randomly oriented PZT thin films pre-heated at 400°C for 10 min and annealed at 600°C for 30 min showed well-defined ferroelectric hysteresis loops with a remnant polarization of 26.57 μC/cm2 and a coercive field of 115.42 kV/cm. The dielectric constant and dielectric loss of the PZT films were 621 and 0.0395, respectively. The microstructures of the thin films are dense, crack-free, and homogeneous with fine grains about 15–20 nm in size.

Effect of Pb Excess Content on Microstructure and Electrical Properties of Sol Gel Derived PZT Thin Films

1999 ◽  
Vol 596 ◽  
Author(s):  
Zhan-jie Wang ◽  
Ryutaro Maeda ◽  
Kaoru Kikuchi
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Sol Gel ◽  
Lead Zirconate ◽  
Pzt Thin Films ◽  
Starting Solution ◽  
Pzt Films

AbstractLead zirconate titanate (PZT) thin films were fabricated by a three-step heat-treatment process which involves the addition of -10, 0 and 10 mol% excess Pb to the starting solution and spin coating onto Pt/Ti/SiO2/Si substrates. Crystalline phases as well as preferred orientations in PZT films were investigated by X-ray diffraction analysis (XRD). The microstructure and composition of the films were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA), respectively. The well-crystallized perovskite phase and the (100) preferred orientation were obtained by adding 10% excess Pb to the starting solution. It was found that PZT films to which 10% excess Pb was added had better electric properties. The remanent polarization and the coercive field of this film were 34.8 μC/cm2 and 41.7 kV/cm, while the dielectric constant and loss values measured at 1 kHz were approximately 1600 and 0.04, respectively. Dielectric and ferroelectric properties were correlated to the microstructure of the films.

Rapid Thermal Processing of Ferroelectric Thin Films

1991 ◽  
Vol 224 ◽  
Author(s):  
Zheng Wu ◽  
Roberto Pascual ◽  
C.V.R. Vasant Kumar ◽  
David Amd ◽  
Michael Sayer
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Thermal Processing ◽  
Crystallization Behavior ◽  
Sol Gel ◽  
Rapid Thermal Processing ◽  
Lead Zirconate ◽  
Dielectric Constants ◽  
Heating Rates ◽  
Pzt Films

AbstractThe preparation of ferroelectric lead zirconate titanate (PZT) thin films by rapid thermal processing (RTP) is reported. The films were deposited by chemical sol gel and physical sputter techniques. The heating rate of RTP was found to have significant influence on the crystallization behavior. Faster heating rates lead to lowering of the crystallization temperature and reduction of grain size. PZT films were obtained with dielectric constants ~ 1000, remanent polarizations between 20 and 30μC/cm2, coercive fields 20 to 60kV/cm, and no significant fatigue for 109 to 1010 stressing cycles.

Preparation of PZT Ferroelectric Thin Films by Sol-Gel Process

2012 ◽  
Vol 204-208 ◽  
pp. 4207-4210 ◽  
Author(s):  
Yu Fei You ◽  
C. H. Xu ◽  
Jun Peng Wang ◽  
Yu Liang Liu ◽  
Jin Feng Xiao ◽  
...  
Keyword(s):  
Thin Films ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Pzt Ceramics ◽  
X Ray ◽  
Pzt Film ◽  
Sol Gel Process ◽  
Pzt Films ◽  
Pzt Ferroelectric Thin Films ◽  
Electronic Microscope

Sol-gel method is used for the formation of Pb(Zr0.63Ti0.37)O3(PZT) thin films. The initial films were formed with spin coating sol solution on silicon wafer and drying coated wet sol film at 300°C for 5min. This process was repeated for 1-4 times to obtain 4 initial films with different thicknesses. 4 initial films were annealed at 500°C for 2h to obtain PZT ceramics films. The morphologies of the surface and cross-section of PZT films were observed with a scanning electronic microscope (SEM). The phase structures of PZT films were analyzed using an X-ray diffraction meter (XRD). Experimental results show that PZT film prepared by coating wet sol on silicon once can be high smooth and compact film.

scholarly journals Local Fatigue Evaluation in PZT Thin Films with Nanoparticles by Piezoresponse Force Microscopy

2012 ◽  
Vol 2012 ◽  
pp. 1-9
Author(s):  
B. S. Li
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Ferroelectric Properties ◽  
Sol Gel ◽  
Precursor Solution ◽  
Grain Morphology ◽  
Piezoresponse Force Microscopy ◽  
Lead Zirconate ◽  
Fatigue Performance ◽  
Pzt Thin Films

Lead zirconate titanate (PZT) thin films with the morphotropic phase boundary composition (Zr/Ti = 52/48) have been prepared using a modified diol-based sol-gel route by introducing 1–5 mol% barium titanate (BT) nanoseeds into the precursor solution on platinized silicon substrates (Pt/Ti/SiO2/Si). Macroscopic electric properties of PZT film with nanoparticle showed a significant improvement of ferroelectric properties. This work aims at the systematic study of the local switching polarization behavior during fatigue in PZT films with and without nanoparticles by using very recent developed scanning piezoelectric microscopy (SPM). We show that the local fatigue performance, which is characterized by variations of local piezoloop with electric cycles, is significantly improved by adding some nanoseeds. It has been verified by scanning electron microscope (SEM) that the film grain morphology changes from columnar to granular structure with the addition of the nanoseeds. On the other hand, the existence of PtxPb transition phase, which existed in interface at early crystallization stage of pure PZT thin film, deteriorates the property of the interface. These microstructures and the interfaces of these films significantly affect the electrons injection occurred on the interfaces. The domain wall pinning induced by injected electrons and the succeeding penetration into the films is discussed to explain the fatigue performance.

Electrode Contacts on PZT Thin Films and Their Influence on Fatigue Properties

1994 ◽  
Vol 361 ◽  
Author(s):  
J.J. Lee ◽  
C.L. Thio ◽  
M. Bhattacharya ◽  
S.B. Desu
Keyword(s):  
Thin Films ◽  
Dielectric Permittivity ◽  
Lead Zirconate Titanate ◽  
Interfacial Layer ◽  
Ruthenium Oxide ◽  
Lead Zirconate ◽  
Fatigue Properties ◽  
Pzt Thin Films ◽  
Pzt Film ◽  
Metal Organic

ABSTRACTThe degradation (fatigue) of dielectric properties of ferroelectric PZT (Lead Zirconate Titanate) thin films during cycling was investigated. PZT thin films were fabricated by metal-organic decomposition (MOD). Samples with electrodes of platinum (Pt) and ruthenium oxide (RuO2) were studied. The interfacial capacitance (if any) at the Pt/PZT and RuO2/PZT interfaces was determined from the thickness dependence of low-field dielectric permittivity (εr) measurements. It was observed that a low εrlayer existed at the Pt/PZT interface but not at the RuO2/PZT interface. The dielectric permittivity of this interfacial layer degrades with increasing fatigue while the εrof the bulk PZT film remains constant. This indicates that fatigue increases the interfacial layer thickness but does not change the bulk properties. For the capacitors with RuO2/PZT/RuO2 structure, however, the εdoes not change with thickness and fatigue cycling. This implies no interfacial layer exists between RuO2/PZT and, therefore, no fatigue was observed. Additionally, an impedance spectroscopie technique has been proposed for possible use in analyzing the nature of the interfacial layer during the fatigue process.

(001)-Oriented LaNiO3 Bottom Electrodes and (001)-Textured Ferroelectric Thin Films on LaNiO3

1999 ◽  
Vol 596 ◽  
Author(s):  
Zhenshan Zhang ◽  
Jeong Hwan Park ◽  
Susan Trolier-McKinstry
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Sol Gel ◽  
Lead Zirconate ◽  
Metallic Oxide ◽  
Working Pressure ◽  
Si Substrates ◽  
Oxide Electrodes ◽  
Pzt Films ◽  
Deposited Films

AbstractIn this work, highly (001)pc-oriented thin films of LaNiO3 (LNO) were deposited by DC magnetron sputtering onto Si substrates (pc = pseudocubic indices). The target powder was prepared using a molten salt technique with Na2CO3 as a flux. The final target density was greater than 85% of theoretical density. The best results were obtained when sputtering was carried out at a power of 186 W and a working pressure of 45 mtorr with a gas composition of 50% O2 + 50% Ar. The thickness of the deposited films was proportional to the sputtering time, and the growth rate was 300Å/hour. Highly (001)-oriented thin films of lead zirconate titanate Pb(Zr0.52Ti0.48)O3 (PZT) and Pb[(Mg1/3Nb2/3)0.7Ti0.3]O3 (PMN-PT) were fabricated by a sol-gel method on (001)-textured LNO metallic oxide electrodes. A remanent polarization of 12 μC/cm2 and d31 of -125 pC/N (assuming a Young's modulus of 35 GPa) were measured on the PMN-PT thin films with a thickness of 0.9 μm. This piezoelectric coefficient considerably exceeds that available from PZT films, and depends critically on the film orientation. Changes in the hysteresis loop due to externally applied stress will also be described.

Effect of Processing Conditions on the Piezoelectric Properties of Sol-gel Derived Pb(Zr,Ti)O3 Films for Micromechanical Applications

2005 ◽  
Vol 20 (6) ◽  
pp. 1428-1435 ◽  
Author(s):  
J. Pérez ◽  
P.M. Vilarinho ◽  
A.L. Kholkin ◽  
J. Manuel Herrero ◽  
C. Zaldo
Keyword(s):  
Lead Zirconate Titanate ◽  
Annealing Temperature ◽  
Piezoelectric Properties ◽  
Sol Gel ◽  
Lead Zirconate ◽  
Piezoelectric Response ◽  
Preparation Conditions ◽  
Sol Gel Process ◽  
Pzt Films ◽  
Interface Effects

Lead zirconate titanate (PZT) films of composition close to the morphotropic phase boundary were deposited onto standard Si/SiO2/Ti/Pt substrates using a modified sol-gel process. The preparation conditions were optimized to obtain high-quality films at sufficiently low temperature (Ta - 500 °C). The dielectric, ferroelectric, and piezoelectric properties of the films were then measured as a function of the annealing temperature and the number of distillations to evaluate their suitability for micromechanical applications. The maximum values of the longitudinal charge and voltage piezoelectric coefficients were d33 ∼ 65 pm/V and g33 ∼ 4 × 10−3 Vm/N, respectively. The results indicate that the piezoelectric properties improved and became saturated with increasing number of distillations and are almost independent on Ta. Only moderate decrease of the piezoelectric response with frequency suggests that the investigated PZT films can be used in high-frequency piezoelectric applications. The results are discussed in terms of the microstructure and interface effects on the piezoelectric deformation in ferroelectric thin films.

Sign in / Sign up

Export Citation Format

Share Document