Effects of Heating Rate and Temperature Holding Time on Mechanical Behaviors of Aluminum Alloy

2007 ◽  
Vol 345-346 ◽  
pp. 33-36
Author(s):  
Chen Guang Huang ◽  
Si Ying Chen ◽  
Chunkui Wang
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
Heating Rate ◽  
Room Temperature ◽  
Thermal Softening ◽  
Holding Time ◽  
Mechanical Behaviors ◽  
Different Temperatures

In this paper, the mechanical properties of several aluminum alloys are obtained experimentally at different temperatures, from room temperature to about 4000C by using the Gleeble 1500 thermomechanical system. Besides, the thermal softening characteristics, effects of heating rate and temperature holding time are discussed in details. It is found that the strength of LF6, a kind of antirust aluminum alloy, is not sensitive to the heating rate (0.1-1000K/s) and temperature holding time (0-1h). However, the mechanical behaviors of other alloys depend on these factors very obviously. At last, these phenomena are discussed in the viewpoint of the microstructures and techniques of ageing strengthening of these alloys.

Effect of Efficient Purification on Mechanical Properties of 3003 Aluminum Alloy

2018 ◽  
Vol 777 ◽  
pp. 402-407
Author(s):  
Gui Qing Chen ◽  
Gao Sheng Fu ◽  
Xiao Dong Lin ◽  
Jun De Wang ◽  
Chao Zeng Cheng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Flow Stress ◽  
Aluminum Alloys ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Deformation Temperature ◽  
Room Temperature ◽  
Inclusion Size ◽  
Isothermal Compression

3003 aluminum melt was treated with efficient purification, and it was deformed by isothermal compression in the range of deformation temperature 300-500 °C at strain rate 0.0l-10.0 s-1 with Gleeble-1500 thermal simulator. The results show that efficient purification treatment can significantly reduce the impurities, and make inclusion size smaller, uniform distribution. Room temperature mechanical properties were significantly improved. At the same strain rate, the flow stress of 3003 aluminum alloy decreases with the increase of deformation temperature. The flow stress increases with the increase of strain rate under the same deformation temperature. Two kinds of 3003 aluminum alloys with different purification treatments both have dynamic recrystallization characteristics. Especially when the strain rate reaches 10.0 s-1, the rheological curve appears sawtooth fluctuation and the alloy may have discontinuous dynamic recrystallization.

Feasibility of Recycling Aluminum Alloy Scrap by Semisolid Extrusion

2008 ◽  
Vol 141-143 ◽  
pp. 79-83
Author(s):  
Sumio Sugiyama ◽  
Jun Yanagimoto
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
Room Temperature ◽  
Hot Extrusion ◽  
True Density ◽  
Metal Mold ◽  
Semisolid Process

The feasibility of recycling machining grindings of aluminum alloys by semisolid process has been investigated. Machining grindings of A2011 aluminum alloy produced experimentally by lathe machining were used. The material is put into a metal mold and compressed up to 90 % of the true density at room temperature. The metal mold with the compressed machining grindings is heated up to a specified temperature. Afterwards, the metal mold is set into the extrusion container, and extrusion in hot and semisolid range was carried out. In this experimental study, extrusion load, internal structure of the product and mechanical properties (tensile strength, elongation, hardness) of the product are assessed. It was proven that semisolid extrusion is about 40% less extrusion load compared with that of hot extrusion, the shape of the machining grindings remained in the hot extrusion and the semisolid extrusion products extrusion ratios higher than 10 have excellent elongation property, which is comparable to the commercialized product.

MICROSTRUCTURES AND ROOM TEMPERATURE MECHANICAL PROPERTIES OF Al--6.3Zn--2.8Mg--1.8Cu CASTING ALUMINUM ALLOY

2013 ◽  
Vol 48 (2) ◽  
pp. 211-219 ◽  
Author(s):  
Guangyu YANG ◽  
Hongshuai MENG ◽  
Shaojun LIU ◽  
Yuanhao QI ◽  
Wanqi JIE
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Room Temperature ◽  
Casting Aluminum Alloy ◽  
Casting Aluminum

The Effect of Heat Treatments and Nickel Additive on The Microstructure and Hardness of 7075 Aluminum Alloy

2019 ◽  
Vol 7 (2) ◽  
pp. 34-41
Author(s):  
Mahmoud Alasad ◽  
Mohamad Yahya Nefawy
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
Artificial Aging ◽  
Heat Treatments ◽  
7075 Aluminum Alloy ◽  
Nickel Additive

The aluminum alloys of the 7xxx series consist of Al with Zn mainly, Mg and Cu. 7xxx aluminum alloys has high mechanical properties making it distinct from other aluminum alloys. In this paper, we examine the effect of adding Nickel and heat treatments on the microstructure and hardness of the 7075 aluminum alloy. Were we added different percentages of nickel [0.1, 0.5, 1] wt% to 7075 Aluminum alloy, and applied various heat treatments (artificial aging T6 and Retrogression and re-aging RRA) on the 7075 alloys that Containing nickel. By applying RRA treatment, we obtained better results than the results obtained by applying T6 treatment, and we obtained the high values of hardness and a smoother microstructure for the studied alloys by the addition of (0.5 wt%) nickel to alloy 7075.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

scholarly journals Elastic, inelastic and time constant measurement for M102 (AL–C–O) dispersions-reinforced aluminum alloys

2020 ◽  
pp. 61-66
Author(s):  
Khaleel Abushgair
Keyword(s):  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
Time Constant ◽  
Room Temperature ◽  
Strain Range ◽  
Time Interval ◽  
Cnc Milling ◽  
Plastic Deformations ◽  
Factors Affecting ◽  
Bulk Content

Purpose. To conduct an experimental study on M102 aluminum alloy bulk content characterization under cyclic loadings for precision applications such as balance machines, optical, and laser instruments. M102 (AL-C-O) dispersion-reinforced aluminum alloy was chosen because of its ability to withstand temperatures beyond 200C and has a better strength than precipitation-hardened Al alloys at room temperature. A CNC milling machine is used to manufacture test samples with longitudinal machining directions. A constant time interval is set for the fabric a quarter-hour span, which is based on the investigation of inelastic and plastic deformations in the nanoscale. Methodology. An electromagnetic test instrument applies a tensile stress range of 10 to 145 N/mm2 to samples with particular shape. It should be noted that interferometers and capacitive sensors were used to measure all forms of deformations with and without loading. The experiments are carried out in a temperature-stable environment of 30.5 C; measurements are taken within a residual strain range of 10 microns. Findings. The results obtained show that results for inelastic deformations for samples of longitudinal cuts direction at 30.5 C were measured under 150 N/mm2 stress as 500 nm inelastic deformation and 100 nm plastic deformation were measured, which is much higher than aluminum alloy studied before at room temperature (20 C). Furthermore, it was found that the time constant of the M102 (ALCO) aluminum alloy samples was double times higher than that for other samples, Originality. For the first time, a study has been conducted on inelastic and plastic deformations in the nanoscale for characterization of M102 aluminum alloy bulk content under cyclic loadings for precision applications. Practical value. One of the main factors affecting the using of other materials than steel in precision applications such as balance machines, optical, and laser instruments is measurement and determination of inelastic, plastic and time constant of the process of delamination of materials of different aluminum alloys since they are nonmagnetic, are easily machined and shaped. This will bring new products and opportunities for these materials.

Effects of Direct Thermal Method Processing Parameters on Mechanical Properties of Semisolid A6061 Feedstock

2021 ◽  
Vol 18 (1) ◽  
Author(s):  
M. F. M. Tajudin ◽  
A. H. Ahmad ◽  
M. M. Rashidi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Room Temperature ◽  
Processing Parameters ◽  
Holding Time ◽  
Thermal Method ◽  
Pouring Temperature ◽  
Porosity Level ◽  
Experimental Works ◽  
Temperature Water

This paper highlights the effects of pouring temperature and holding time on the mechanical properties of aluminium 6061 semisolid feedstock billets. The semisolid metal feedstock billets were prepared by a direct thermal method (DTM), in which the molten metal was poured into a cylindrical copper mould with a different combination of pouring temperature and holding time before it was solidified in room temperature water. The results show that the sample with pouring temperature slightly above aluminium 6061 liquidus temperature has the lowest porosity, thereby the highest mechanical properties value. The sample with a pouring temperature of 660 °C and holding time of 60 s has the density, tensile strength and hardness properties of 2.701 g/cm3, 146.797 MPa, and 86.5 HV, respectively. Meanwhile, the sample at a pouring temperature of 640 °C and holding time of 20 s has density, tensile strength and hardness properties of 2.527 g/cm3, 65.39 MPa, and 71.79 HV, respectively. The density and fractography tests were conducted to confirm the existence of porosity within the samples. The results from these experimental works suggested that the mechanical properties of DTM semisolid feedstock billet merely depended on processing parameters, which influenced the porosity level within the feedstock billet, thus directly affected their mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document