Mechanical Properties of Concrete Produced with Wastepaper for Application of Construction Materials

2014 ◽  
Vol 627 ◽  
pp. 369-372
Author(s):  
Hyun Ki Choi
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Construction Materials ◽  
Mix Design ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Mixing Ratio ◽  
Replacement Ratio ◽  
Influence Variable ◽  
Test Result

The purpose of this study was to analyze the mechanical properties of concrete produced with wastepaper for obtaining the optimum mix design of that. The concrete produced with wastepaper was made up of the cement, water, sand, and cut wastepaper. For this purpose, the concrete which had variety mixing ratio of materials was mixed and cured to find out the mechanical properties of that. And, it was performed the compressive and tensile test and the measurement of hardened concrete. The test result of this study was showed that the partial replacement ratio of wastepaper was the decisive influence variable and the correlation between the mechanical properties

The Behavior of FRA Concrete with High Replacement Ratio

2018 ◽  
Vol 760 ◽  
pp. 204-209 ◽  
Author(s):  
Magdaléna Šefflová
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Absorption Capacity ◽  
Recycled Aggregate ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Replacement Ratio ◽  
Natural Sand ◽  
Concrete Mixtures

This study deals with determination of the properties of the fine recycled aggregate (FRA) concrete with partial replacement of natural sand in concrete mixtures. The FRA was obtained from concrete waste and crushed on fraction 0 – 4 mm by laboratory jaw crusher. The geometrical and physical properties of natural sand and the FRA were tested. The main goal of this study is evaluation of the basic physical and mechanical properties of the concrete with partial natural sand replacement by the FRA such as workability, water absorption capacity, compressive strength and flexural strength. A total four concrete mixtures were prepared. The first concrete mixture was prepared only with natural sand, did not include the FRA. In other concrete mixtures, natural sand was replaced by the FRA in various replacement ratios (40 %, 50 %, and 60 %). All concrete mixtures were designated with the same parameters for clear comparison. The workability of fresh concrete mixtures and physical and mechanical properties of hardened concrete were tested.

Evaluation of Mechanical Properties of BAGcrete

2014 ◽  
Vol 984-985 ◽  
pp. 693-697
Author(s):  
K. Rekha ◽  
R. Thenmozhi
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Mineral Admixture ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Test Results ◽  
Replacement Ratio ◽  
Blended Cements ◽  
Sugarcane Bagasse Ash ◽  
Partial Cement Replacement

The usage of waste materials in making concrete gives a satisfactory solution to some of the problems related to waste management and environmental concerns. In the development of blended cements, some of the Agro wastes such as sugarcane bagasse ash, rice husk ash and wheat straw ash are used as pozzolanic materials. Few studies have been reported on the use of bagasse ash (BA) as partial cement replacement material. This research aims to study the physical and mechanical properties of hardened concrete prepared with bagasse ash as partial replacement material for cement are reported. The Portland cement was replaced with BA in the ratio of 0%, 5%, 10%, 15% and 20% of weight of cement. The compressive strength, splitting tensile strength and flexural strength of concrete at the age of 28 days were investigated. From the test results it was observed that bagasse ash is an effective mineral admixture, with 5% as optimal replacement ratio of cement.

scholarly journals Utilization of Construction Waste as Partial Replacement of Aggregates in Cement Concrete

2019 ◽  
Vol 8 (9S) ◽  
pp. 1028-1032
Keyword(s):  
Mechanical Properties ◽  
Sustainable Development ◽  
Coarse Aggregate ◽  
Construction Materials ◽  
Recycled Aggregates ◽  
Partial Replacement ◽  
Ceramic Tiles ◽  
Replacement Ratio ◽  
Construction Waste ◽  
Natural Aggregates

This paper containsstudy of marble waste asreplacement of fine andcoarseaggregatesinconcrete. Entire planetisfacing anissue of environment and climate.In this era sustainable development isin huge demand. Sustainable development has way of possibility by revising, rethinking, reducing, reusing. The use of construction waste materials in concrete industrial is playing key role to its economic, eco-friendly,green paybacksand engineering. Thisreviewreportsonthe utilization of wastemarble as aggregate inconcrete productionindustry. On the base of the reviewed studies, it was experiential that construction waste used in place of coarse aggregate contribute to the workability and mechanical properties of concrete. When natural aggregates relaced with coarse marble aggregates, ceramic tiles, recycled aggregates, it attained the bestresults at full replacement ratio. Additionally, waste construction materials in coarse aggregate form improves the mechanical properties overthe dust form. These sustainable alternatives not only enhance mechanical properties of concrete but also boost economy.

Earth-Based Mortars: Mix Design, Mechanical Characterization and Environmental Performance Assessment

2022 ◽  
Author(s):  
Rayane de Lima Moura Paiva ◽  
Adriana Paiva Souza Martins ◽  
Lucas Rosse Caldas ◽  
Oscar A.M. Reales ◽  
Romildo Dias Toledo Filho
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Environmental Impacts ◽  
Calcium Chloride ◽  
Clay Fraction ◽  
Supplementary Cementitious Materials ◽  
Mix Design ◽  
Partial Replacement ◽  
Promising Alternative ◽  
The Earth

The incorporation of sustainable materials in the civil construction sector has grown in recent years to minimize environmental impacts. Among these materials, the use of earth, a local raw material that does not require much energy for its processing, appears as an advantageous and promising alternative. Earth mortars stabilized with natural binders, when compared to conventional mortars, can have technological, economic and environmental advantages. The objective of this work was to develop an earth-based mortar stabilized with mineral binders using a 1:3 binder to aggregate mass proportion, and to evaluate its fresh and hardened state properties, as well as its environmental impacts using Life Cycle Assessment (LCA) with a cradle to gate scope. The selected materials were divided in four groups: (i) cement, hydrated lime, fly ash and metakaolinite (binders), (ii) natural sand and coarse fraction of the earth (aggregates), (iii) calcium chloride and superplasticizer (additives) and (iv) water. In the matrix formulation the clay fraction from earth constituted the majority of the binder. The selection of supplementary cementitious materials as additional binders provided improvements in workability and mechanical properties of the mortar. A mix design was carried out using different cement (5; 7.5 and 10%) and fly ash (11; 13.5 and 16%) mass percentages. The water/binder material ratio, superplasticizer content and calcium chloride content were 0.65; 2% and 1%, respectively. The results showed that an increase in fly ash content combined with a decrease in cement content provided an increase in workability and a decrease in mechanical properties of mortars. Nevertheless, the mechanical performance of the mortars remained above the minimum values prescribed in Brazilian construction codes. From the results analysis it was concluded that partial replacement of cement by fly ash provided greater workability in the fresh state and reduced the environmental impacts of the earth-based mortar.

scholarly journals Experimental Examination on Mechanical Properties of Polypropylene Fiber Blended Concrete as Partial Replacement of Sand as Stone Quarry Dust

2020 ◽  
Vol 9 (7) ◽  
pp. 623-627
Keyword(s):  
Mechanical Properties ◽  
Polypropylene Fiber ◽  
Construction Materials ◽  
Drying Shrinkage ◽  
Partial Replacement ◽  
Normal Stresses ◽  
Experimental Examination ◽  
Concrete Members ◽  
Maximum Value ◽  
Quarry Dust

Concrete is recognized as a quite breakable material when exposed to impact loading and normal stresses. Concrete tensile strength is nearly one-tenth of its compressive strength. As a result of which concrete members are not able to support such stresses and loads which mainly occurs in most concrete structures. So, we mainly reinforce it with such materials which help it to increase its tensile and flexural strength. Fibers are the material which helps to increase the toughness and durability of concrete and reduce plastic and drying shrinkage. As we know cement, sand and aggregate are three basic construction materials. Due to the huge demand for these materials, their deposits are scarce. So, we need to find the material which can replace them partially and fully. Stone quarry dust is material that may be used to replace sand partially and fully. In this study, the casting of moulds for various percentage of stone quarry dust (5%, 10%, 20%, 30%, 40%, and 50%) is carried and maximum value for stone quarry dust is obtained. After obtaining the max value of stone quarry dust at 10% it is replaced with various percentages of polypropylene fiber (0%, 0.1%, 0.2% and 0.3%). This study aims to investigate the limit up to which stone quarry can be replaced with sand for M35 grade of concrete and to investigate the combined effect of stone quarry dust (10%) and polypropylene fiber with varying percentage (0%, 0.1%, 0.2%, and 0.3%).

scholarly journals Partial Replacement of Ordinary Portland Cement with Sawdust Ash in Concrete

2019 ◽  
pp. 1-7
Author(s):  
L. S. Gwarah ◽  
B. M. Akatah ◽  
I. Onungwe ◽  
P. P. Akpan
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Construction Materials ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Flow Table ◽  
Compressive Strength Test ◽  
Increasing Demand ◽  
Mixed Concrete

The investigation of sawdust ash (SDA) as a partial replacement for cement in concrete was studied owing to the high cost and increasing demand for cement in a harsh economy and considering the presence of limited construction materials and waste to wealth policy. Ordinary Portland Cement (OPC) was replaced by 0%, 5%, 10%, 15%, 20%, 25% and 30% of SDA. Slump test and consistency test (flow table apparatus test) were conducted on the freshly mixed concrete sample, and compressive strength test was conducted on the hardened concrete cubes of 150mm2, which was cured between 7, 14, 21 and 28 days. The results revealed that the slump decreases as the SDA content increases in percentage, while the consistency of the freshly mixed concrete remarkably moves from high, medium to low as the SDA content increases. The compressive strength of the hardened concrete undergone a decrease in strength, as the partial replacement of OPC with SDA increases. By the results interpretation, it is observed that 5% to 10% SDA when replaced with OPC can still result in the desired strength of concrete.

An Experiment Investigation on Physical and Mechanical Properties of High Strength Concrete with Suitable Admixture

2019 ◽  
Vol 972 ◽  
pp. 10-15
Author(s):  
B.C. Gayana ◽  
Mallikarjuna Shashanka ◽  
Avinash N. Rao ◽  
Karra Ram Chandar
Keyword(s):  
Mechanical Properties ◽  
High Strength Concrete ◽  
Construction Material ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Steel Fibers ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Conventional Concrete ◽  
Strength Concrete

Concrete is an essential construction material. Even-though conventional concrete performs and satisfy the structures under normal conditions, a few special situations require very high compressive strength of concrete. An experimental investigation is done to develop high strength concrete with suitable admixtures and steel fibers. The properties of fresh and hardened concrete with alccofine as partial replacement for binder and poly-carboxylate ether (Glenium 8233) and steel fibers is investigated for the workability and mechanical properties i.e., compressive, splitting tensile and flexural strength of concrete. Based on the results, the strength increased with the addition of alccofine compared to the control mix. Hence, by optimum percentage of alccofine, high strength of concrete of 112 MPa can be obtained.

scholarly journals Improving Astm A516 Grade 70 Mechanical Properties by Sandblasting Process

2018 ◽  
Vol 7 (4.35) ◽  
pp. 216
Author(s):  
Omar Suliman Zaroog ◽  
S.A.P. Sughanthy ◽  
Mohd Rashdan Isa ◽  
M.N.M. Ansari
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tensile Test ◽  
Hardness Test ◽  
Time Duration ◽  
Before And After ◽  
Tensile Test Result ◽  
Test Result

Nowadays, sandblasting is commonly use in industries. The ability of sandblasting is to remove any stain, unwanted matter and many other functions making this process generally used worldwide. The effect of sandblasting on mechanical properties of ASTM A516 grade 70 was investigated in this study. Samples of the material have been sandblasted with different size of grits and times. Surface roughness, hardness and tensile was measured before and after sandblasting. The roughness test result showed that when the time duration of sandblasting increased, the roughness of the specimen also increased. Based on hardness test result, it showed that the hardness improved when the smallest size of grits was applied. However, the hardness decreased when the size of grits and time was increased. The tensile test result pattern showed quite similar to hardness test result. The size of grits and time duration for sandblasting need to set depending on application of the sandblasting process usage applied to the samples or materials.

Changes of Mechanical Properties of Lightweight Cement Mortar Mixed with Recycled Expanded Polystyrene and Subjected to High Temperatures

2014 ◽  
Vol 1051 ◽  
pp. 752-756 ◽  
Author(s):  
Rocío Sancho ◽  
Ángel Castillo ◽  
Ma Eugenia Maciá ◽  
Rosa Corral
Keyword(s):  
Mechanical Properties ◽  
High Temperatures ◽  
Mechanical Response ◽  
Cement Mortar ◽  
Construction Materials ◽  
Lightweight Aggregate ◽  
Expanded Polystyrene ◽  
Partial Replacement ◽  
Different Temperatures ◽  
Residual Product

The main aim of this paper is to evaluate the influence of the recycled expanded polystyrene as lightweight aggregate on the mechanical properties of lightweight cement mortar when subjected to high temperatures.Various tests have been carried out on different mixtures of mortar. The water/cement mix proportion has always been the same and only the nature of the aggregates has changed, with a partial replacement of the conventional aggregate by recycled ground EPS (EPS-G) with values ranging from 10% to 30%, achieving significant results in relation to exposure to high temperatures. In this research, the samples have been subjected to different temperatures of exposure, in order to analyze the influence of the lightweight recycled arid dosage in the mechanical properties of mortars.The results of this study show the ability of mechanical response at high temperatures with light mortars EPS-G. This study shows how this new mix can be used in different building types, optimizing construction materials and reducing mortars density while transforming a residual product into an active product.

scholarly journals Mechanical Characteristics of Hardened Concrete with Different Mineral Admixtures: A Review

2014 ◽  
Vol 2014 ◽  
pp. 1-15 ◽  
Author(s):  
Tehmina Ayub ◽  
Sadaqat Ullah Khan ◽  
Fareed Ahmed Memon
Keyword(s):  
Mechanical Properties ◽  
Mechanical Characteristics ◽  
Drying Shrinkage ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Granulated Blast Furnace Slag ◽  
Shrinkage And Creep ◽  
Furnace Slag

The available literature identifies that the addition of mineral admixture as partial replacement of cement improves the microstructure of the concrete (i.e., porosity and pore size distribution) as well as increasing the mechanical characteristics such as drying shrinkage and creep, compressive strength, tensile strength, flexural strength, and modulus of elasticity; however, no single document is available in which review and comparison of the influence of the addition of these mineral admixtures on the mechanical characteristics of the hardened pozzolanic concretes are presented. In this paper, based on the reported results in the literature, mechanical characteristics of hardened concrete partially containing mineral admixtures including fly ash (FA), silica fume (SF), ground granulated blast furnace slag (GGBS), metakaolin (MK), and rice husk ash (RHA) are discussed and it is concluded that the content and particle size of mineral admixture are the parameters which significantly influence the mechanical properties of concrete. All mineral admixtures enhance the mechanical properties of concrete except FA and GGBS which do not show a significant effect on the strength of concrete at 28 days; however, gain in strength at later ages is considerable. Moreover, the comparison of the mechanical characteristics of different pozzolanic concretes suggests that RHA and SF are competitive.

Sign in / Sign up

Export Citation Format

Share Document