Effect of Silica Base Catalyst on Transformation of Methanol to Hydrocarbon

2017 ◽  
Vol 751 ◽  
pp. 512-517 ◽  
Author(s):  
Supranee Lao-Ubol ◽  
Phunthinee Somwongsa ◽  
Pracha Laoauyporn ◽  
Pasinee Panith ◽  
Siriporn Larpkiattaworn ◽  
...  
Keyword(s):  
Pore Diameter ◽  
Fixed Bed ◽  
Methanol Conversion ◽  
Liquid Hydrocarbon ◽  
Product Distribution ◽  
Catalytic Performance ◽  
Zeolite Catalysts ◽  
Fixed Bed Reactor ◽  
Phosphorus Species ◽  
Methanol To Hydrocarbon

Five different types of silica catalyst (SBA-15, SBA-15-PO3H2, and three different Si/Al ratio of commercial zeolites (30, 80 and 280) were used to study the transformation of methanol to hydrocarbon (MTH). The aim of this study was to investigate the effect of pore diameter and acidity in the structure of silica catalysts on the process performances in terms of methanol conversion and hydrocarbon selectivity. The mesoporous silica catalysts were prepared by co-condensation method. The catalysts samples were characterized by GC-MS, XRD, BET, and NH3-TPD techniques. The catalytic performance of synthesized and commercial catalysts for MTH process was evaluated using a homemade fixed bed reactor at temperature (300°C). It was found that the liquid hydrocarbon product provided by zeolite catalysts is aromatic hydrocarbons-rich. High Si/Al zeolites with larger pore size lead to higher selectivity and yield to paraffins (C1-C7). In contrast to commercial zeolite catalyst, SBA-15 and its modification with phosphorus species showed no conversion under studied condition. These results indicate that both pore diameter and acidity influence the product distribution in methanol to hydrocarbon process.

scholarly journals Hierarchical H-ZSM5 zeolites based on natural kaolinite as a high-performance catalyst for methanol to aromatic hydrocarbons conversion

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Ahmad Asghari ◽  
Mohammadreza Khanmohammadi Khorrami ◽  
Sayed Habib Kazemi
Keyword(s):  
Pore Size ◽  
Aromatic Hydrocarbons ◽  
High Performance ◽  
Low Cost ◽  
Direct Synthesis ◽  
Fixed Bed ◽  
Methanol Conversion ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Good Prospect

AbstractThe present work introduces a good prospect for the development of hierarchical catalysts with excellent catalytic performance in the methanol to aromatic hydrocarbons conversion (MTA) process. Hierarchical H-ZSM5 zeolites, with a tailored pore size and different Si/Al ratios, were synthesized directly using natural kaolin clay as a low-cost silica and aluminium resource. Further explored for the direct synthesis of hierarchical HZSM-5 structures was the steam assisted conversion (SAC) with a cost-effective and green affordable saccharide source of high fructose corn syrup (HFCS), as a secondary mesopore agent. The fabricated zeolites exhibiting good crystallinity, 2D and 3D nanostructures, high specific surface area, tailored pore size, and tunable acidity. Finally, the catalyst performance in the conversion of methanol to aromatic hydrocarbons was tested in a fixed bed reactor. The synthesized H-ZSM5 catalysts exhibited superior methanol conversion (over 100 h up to 90%) and selectivity (over 85%) in the methanol conversion to aromatic hydrocarbon products.

scholarly journals Catalytic Performance of Phosphorus Incorporated HZSM-5 in Coupling Transformation of Methanol with 1-butene to Propylene

2021 ◽  
Vol 72 (3) ◽  
pp. 33-44
Author(s):  
Haifeng Tian ◽  
Yongyong Nan ◽  
Jinlong Lv ◽  
Fei Zha ◽  
Xiaohua Tang ◽  
...  
Keyword(s):  
Fixed Bed ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Molar Ratio ◽  
N2 Adsorption ◽  
Facile Hydrothermal Method ◽  
Phosphorus Species ◽  
Coupling Transformation ◽  
Ft Ir ◽  
Adsorption Desorption

Directly incorporated phosphorus species into the framework of HZSM-5 zeolite (H[P, Al]-ZSM-5) was successfully synthesized by the facile hydrothermal method. It was characterized by employing XRD, ICP-OES, SEM, FT-IR, N2 adsorption-desorption, NH3-TPD, XPS and TG-DTA, respectively. The effects of the phosphorus species content, temperature, WHSV, and the molar ratio of methanol/1-butene in coupling transformation of methanol with 1-butene to propylene catalyzed by H[P, Al]-ZSM-5 in a fixed bed reactor were studied systematically. Tests have suggested the acid content and specific surface area of H[P, Al]-ZSM-5 are reduced. Under the condition of reaction temperature at 550�Z, molar ratio of methanol/1-butene to 1.0, reaction pressure at 0.1 MPa and WHSV= 3.53 h-1, the P-modified HZSM-5 zeolite (with the P2O5 molar composition of 0.4 )the selectivity and yield of propylene are 35.6% and 32.5%, respectively.

Kinetic Study of the Simultaneous Cracking of Paraffins and Methanol on HZSM-5 Zeolite Catalysts

2007 ◽  
Vol 5 (1) ◽  
Author(s):  
Diana Mier ◽  
Andrés Tomás Aguayo ◽  
Alaitz Atutxa ◽  
Ana G Gayubo ◽  
Javier Bilbao
Keyword(s):  
Kinetic Model ◽  
Catalyst Deactivation ◽  
Fixed Bed ◽  
Acid Catalyst ◽  
Product Distribution ◽  
Operating Conditions ◽  
Zeolite Catalysts ◽  
Fixed Bed Reactor ◽  
Light Olefins ◽  
Feed Temperature

A study has been carried out on the effect of acid catalyst properties and operating conditions (methanol/n-butane ratio in the feed, temperature, space time, time on stream) on the yield of light olefins (C2-C4) in the simultaneous cracking of n-butane and methanol. The operation has been carried out in an isothermal fixed bed reactor in the 400-575 °C range, using catalysts prepared based on HZSM-5 zeolites (with different Si/Al ratio), HY, Ni/HZSM-5 and SAPO-18. The results are evidence of a synergism between the transformation reactions of both reactants, whose consequence is an increase in the yield of olefins that correspond to the transformation of methanol and the cracking of n-butane. Furthermore, catalyst deactivation by coke is significantly attenuated compared to the corresponding transformation of methanol. Based on the effect of operating conditions on product distribution, a kinetic model is proposed by combining the schemes corresponding to the transformation of individual components.

scholarly journals Performance of Activated Carbon Supported Cobalt Oxides and Iron Oxide Catalysts in Catalytic Cracking of Waste Cooking Oil

2021 ◽  
Author(s):  
Tavayogeshwary Thangadurai ◽  
Ching Thian Tye
Keyword(s):  
Activated Carbon ◽  
Catalytic Cracking ◽  
Catalyst Activity ◽  
Fixed Bed ◽  
Liquid Hydrocarbon ◽  
Waste Cooking Oil ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Cooking Oil ◽  
Hydrocarbon Yield

This work studied the catalyst activity of activated carbon (AC) supported Co, Fe and Co-Fe oxides in catalytic cracking of waste cooking oil. Reactions were carried out in a fixed bed reactor at 450 °C with WHSV 9 hr–1. Single metal Co/AC and Fe/AC catalysts with different metal loading (2.5–15 wt.%) and bimetal xCo-yFe/AC (x, y = 2.5 to 12.5 wt.%; x + y =15 wt.%) catalysts were investigated. Co/AC and Fe/AC catalysts both contributed to significant liquid yield with high selectivity towards C15 and C17 hydrocarbons. Fe/AC catalysts gave high C5 – C20 hydrocarbon yield whereas Co/AC attained more palmitic (C16) and oleic (C18) acid conversion. Synergistic effect in two metals Co-Fe/AC catalysts had further improved the liquid hydrocarbon yield (up to ~93 %) and fatty acid conversion (up to 94 %). The best catalyst, 10Co-5Fe/AC had been further tested under the effect of reaction temperature, feed flow rate (WHSV) and deactivation for its catalytic performance.

Dimethyl Ether Synthesis via Methanol Dehydration over Diatomite Catalyst Modified Using Hydrochloric Acid

2014 ◽  
Vol 931-932 ◽  
pp. 42-46 ◽  
Author(s):  
Watcharakorn Pranee ◽  
Pornsawan Assawasaengrat ◽  
Arthit Neramittagapong ◽  
Sutasinee Neramittagapong
Keyword(s):  
Hydrochloric Acid ◽  
Dimethyl Ether ◽  
Active Sites ◽  
Fixed Bed ◽  
Methanol Conversion ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Methanol Dehydration ◽  
Dimethyl Ether Synthesis ◽  
Ether Synthesis

The synthesis of dimethyl ether via methanol dehydration has been carried out over untreated-diatomite catalyst (DM) and hydrochloric acid modified treatment on diatomite catalyst (DMHC). The reactions were carried out in a fixed-bed reactor. The effects of hydrochloric acid modifications of diatomite on its catalytic performance were studied. The characterization such as XRD, SEM, FT-IR and FT-Raman had no deformation after HCl-modified treatment on catalysts. DMHC catalyst apparently gave the higher methanol conversion rate than DM due to the acidity while the selectivity of dimethyl ether from 250 to 350°C was slightly changed. The acidity was depended upon Al(IV) ions; nevertheless, both Al(V) and Al(VI) were affected and hence increasing the basic active sites. Not only was the competitively catalytic methanol dehydrogenation preferred with basic condition but also methanol-blocking water molecule interaction was the unwanted reaction. In this investigation, the chemical-bond arrangements of silicon and aluminium ions were proposed with solid MAS/NMR. The DMHC catalyst exhibited better DME yield than the DM catalyst, and it could be used as a selective catalyst for DME synthesis from methanol.

CO2 valorization into synthetic natural gas (SNG) using a Co–Ni bimetallic Y2O3 based catalysts

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Radwa A. El-Salamony ◽  
Sara A. El-Sharaky ◽  
Seham A. Al-Temtamy ◽  
Ahmed M. Al-Sabagh ◽  
Hamada M. Killa
Keyword(s):  
Reaction Mechanism ◽  
Natural Gas ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Molar Ratio ◽  
Impregnation Method ◽  
Synthetic Natural Gas ◽  
Methanation Reaction ◽  
Co2 Valorization

Abstract Recently, because of the increasing demand for natural gas and the reduction of greenhouse gases, interests have focused on producing synthetic natural gas (SNG), which is suggested as an important future energy carrier. Hydrogenation of CO2, the so-called methanation reaction, is a suitable technique for the fixation of CO2. Nickel supported on yttrium oxide and promoted with cobalt were prepared by the wet-impregnation method respectively and characterized using SBET, XRD, FTIR, XPS, TPR, and HRTEM/EDX. CO2 hydrogenation over the Ni/Y2O3 catalyst was examined and compared with Co–Ni/Y2O3 catalysts, Co% = 10 and 15 wt/wt. The catalytic test was conducted with the use of a fixed-bed reactor under atmospheric pressure. The catalytic performance temperature was 350 °C with a supply of H2:CO2 molar ratio of 4 and a total flow rate of 200 mL/min. The CH4 yield was reached 67%, and CO2 conversion extended 48.5% with CO traces over 10Co–Ni/Y2O3 catalyst. This encourages the direct methanation reaction mechanism. However, the reaction mechanism over Ni/Y2O3 catalyst shows different behaviors rather than that over bi-metal catalysts, whereas the steam reforming of methane reaction was arisen associated with methane consumption besides increase in H2 and CO formation; at the same temperature reaction.

scholarly journals Performance Analysis of TiO2-Modified Co/MgAl2O4 Catalyst for Dry Reforming of Methane in a Fixed Bed Reactor for Syngas (H2, CO) Production

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3347
Author(s):  
Arslan Mazhar ◽  
Asif Hussain Khoja ◽  
Abul Kalam Azad ◽  
Faisal Mushtaq ◽  
Salman Raza Naqvi ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Dry Reforming ◽  
Fixed Bed Reactor ◽  
Dry Reforming Of Methane ◽  
Catalyst Stability ◽  
Feed Ratio ◽  
Catalyst Loading ◽  
Impregnation Method

Co/TiO2–MgAl2O4 was investigated in a fixed bed reactor for the dry reforming of methane (DRM) process. Co/TiO2–MgAl2O4 was prepared by modified co-precipitation, followed by the hydrothermal method. The active metal Co was loaded via the wetness impregnation method. The prepared catalyst was characterized by XRD, SEM, TGA, and FTIR. The performance of Co/TiO2–MgAl2O4 for the DRM process was investigated in a reactor with a temperature of 750 °C, a feed ratio (CO2/CH4) of 1, a catalyst loading of 0.5 g, and a feed flow rate of 20 mL min−1. The effect of support interaction with metal and the composite were studied for catalytic activity, the composite showing significantly improved results. Moreover, among the tested Co loadings, 5 wt% Co over the TiO2–MgAl2O4 composite shows the best catalytic performance. The 5%Co/TiO2–MgAl2O4 improved the CH4 and CO2 conversion by up to 70% and 80%, respectively, while the selectivity of H2 and CO improved to 43% and 46.5%, respectively. The achieved H2/CO ratio of 0.9 was due to the excess amount of CO produced because of the higher conversion rate of CO2 and the surface carbon reaction with oxygen species. Furthermore, in a time on stream (TOS) test, the catalyst exhibited 75 h of stability with significant catalytic activity. Catalyst potential lies in catalyst stability and performance results, thus encouraging the further investigation and use of the catalyst for the long-run DRM process.

LPG Synthesis from Syngas over Cu/ZnO-Pd-β Catalysts Prepared by Ultrasonic Spray Pyrolysis

2015 ◽  
Vol 659 ◽  
pp. 252-256
Author(s):  
Sudarat Chaiwatyothin ◽  
Wittawat Ratanathavorn ◽  
Tharapong Vitidsant ◽  
Prasert Reubroycharoen
Keyword(s):  
Spray Pyrolysis ◽  
Fixed Bed ◽  
Ultrasonic Spray Pyrolysis ◽  
Product Distribution ◽  
Fixed Bed Reactor ◽  
Spherical Particles ◽  
Gaseous State ◽  
X Ray ◽  
Ultrasonic Spray ◽  
Co Conversion

Synthesis of nanoCu/ZnO catalyst for LPG production was prepared by ultrasonic spray pyrolysis (USP). Hollow spherical particles were obtained by USP technique using an aqueous solution of Cu (NO3)3.6H2O and Zn (NO3)3.3H2O with different concentration of 0.05, 0.1 and 0.5 molar under the pyrolysis temperatures of 600, 700 and 800°C. Mists of the solution were generated from the precursor solution by ultra sonic vibrators at frequency of ~1.7 MHz. The physicochemical properties of catalysts were characterized by X-ray diffraction, temperature-programmed reduction, scanning electron microscope, nitrogen adsorption-desorption, and energy dispersive X-ray spectrometer. The results showed that increasing in precursor concentration resulted in a large particle and particles size distributed in a range of 0.63-1.21 μm. Particles prepared at pyrolysis temperature 700°C exhibited homogeneous in size and shape compared to other temperature. The catalytic activity of nanoCu/ZnO-Pd-β catalysts was performed in a fixed-bed reactor for synthesizing LPG. The reaction took place at 260°C, 3.0 MPa, and the ratio of H2/CO = 2/1. All the products from the reactor were in gaseous state, and analyzed by on-line gas chromatography. The results showed that %CO conversion was high but decreased rapidly with increasing reaction time. Cu/ZnO catalyst prepared by co-precipitation gave higher %CO conversion than that prepared by ultrasonic spray pyrolysis. Moreover, hydrocarbon product distribution for Cu/ZnO catalyst produced at concentration 0.1 M 700°C by ultrasonic spray pyrolysis gave the highest LPG selectivity.

Effect of CO Conversion on the Product Distribution of a Co/Al2O3 Fischer–Tropsch Synthesis Catalyst Using a Fixed Bed Reactor

2012 ◽  
Vol 142 (11) ◽  
pp. 1382-1387 ◽  
Author(s):  
Dragomir B. Bukur ◽  
Zhendong Pan ◽  
Wenping Ma ◽  
Gary Jacobs ◽  
Burtron H. Davis
Keyword(s):  
Fixed Bed ◽  
Product Distribution ◽  
Tropsch Synthesis ◽  
Fixed Bed Reactor ◽  
Fischer Tropsch ◽  
Fischer Tropsch Synthesis ◽  
Co Conversion
Sign in / Sign up

Export Citation Format

Share Document