The Effect of Explosion in a Tunnel Tube on its Damage

2018 ◽  
Vol 774 ◽  
pp. 265-270
Author(s):  
Petr P. Prochazka ◽  
Martin J. Válek
Keyword(s):  
Gas Dynamics ◽  
Solid Phase ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Structure ◽  
Air Velocity ◽  
Shell Elements ◽  
Final Volume ◽  
Flat Shell ◽  
The Impact ◽  
Geometric Compatibility

The aim of the work is to study the impact of an explosion in a tube on its damage. The theory of Landau-Liftschitz gas dynamics and the damage criterion by the Hoek-Brown in the structure are applied. If the charge is placed centrically in the tube, it is fairly easy to predict both the locations and damage levels. Therefore, the paper is oriented to the case where the charge is placed eccentrically. Air movement is described by the solution of non-linear Euler’s equations by final volume element method, while the response of the fiber reinforced concrete structure of the tube to impact waves is described by the time dependent 20-nodes flat shell elements. In order to ensure the geometric compatibility along the interface between the two media (structure, air), gas dynamics in the air is described by block elements, while the shell is approximated by the finite element. In this way, the problem solved is divided into a description of the air velocity and pressure and the velocity and stress in the solid phase, separately; interaction of the effects caused by the explosion initiated inside of the tube and its impact on the solid phase is concentrated along the interface between these two media. The calculation focuses on the early stages of interaction development when most likely damage is assumed.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

Development of Strategies for Glycopeptide Synthesis: An Overview on the Glycosidic Linkage

2020 ◽  
Vol 24 (21) ◽  
pp. 2475-2497
Author(s):  
Andrea Verónica Rodríguez-Mayor ◽  
German Jesid Peralta-Camacho ◽  
Karen Johanna Cárdenas-Martínez ◽  
Javier Eduardo García-Castañeda
Keyword(s):  
Chemical Synthesis ◽  
Solid Phase ◽  
Building Blocks ◽  
Heterogeneous Environments ◽  
Phase Synthesis ◽  
Low Concentrations ◽  
Biological Sources ◽  
Synthetic Routes ◽  
The Impact ◽  
Potential Use

Glycoproteins and glycopeptides are an interesting focus of research, because of their potential use as therapeutic agents, since they are related to carbohydrate-carbohydrate, carbohydrate-protein, and carbohydrate-lipid interactions, which are commonly involved in biological processes. It has been established that natural glycoconjugates could be an important source of templates for the design and development of molecules with therapeutic applications. However, isolating large quantities of glycoconjugates from biological sources with the required purity is extremely complex, because these molecules are found in heterogeneous environments and in very low concentrations. As an alternative to solving this problem, the chemical synthesis of glycoconjugates has been developed. In this context, several methods for the synthesis of glycopeptides in solution and/or solid-phase have been reported. In most of these methods, glycosylated amino acid derivatives are used as building blocks for both solution and solid-phase synthesis. The synthetic viability of glycoconjugates is a critical parameter for allowing their use as drugs to mitigate the impact of microbial resistance and/or cancer. However, the chemical synthesis of glycoconjugates is a challenge, because these molecules possess multiple reaction sites and have a very specific stereochemistry. Therefore, it is necessary to design and implement synthetic routes, which may involve various protection schemes but can be stereoselective, environmentally friendly, and high-yielding. This review focuses on glycopeptide synthesis by recapitulating the progress made over the last 15 years.

Introduction to geomicrobiology

2018 ◽  
Author(s):  
David L. Kirchman
Keyword(s):  
Fossil Fuels ◽  
Solid Phase ◽  
Direct Reduction ◽  
Iron Oxidation ◽  
Mineral Dissolution ◽  
Precipitation Process ◽  
Soluble Ions ◽  
Chemolithoautotrophic Bacteria ◽  
The Impact

Geomicrobiology, the marriage of geology and microbiology, is about the impact of microbes on Earth materials in terrestrial systems and sediments. Many geomicrobiological processes occur over long timescales. Even the slow growth and low activity of microbes, however, have big effects when added up over millennia. After reviewing the basics of bacteria–surface interactions, the chapter moves on to discussing biomineralization, which is the microbially mediated formation of solid minerals from soluble ions. The role of microbes can vary from merely providing passive surfaces for mineral formation, to active control of the entire precipitation process. The formation of carbonate-containing minerals by coccolithophorids and other marine organisms is especially important because of the role of these minerals in the carbon cycle. Iron minerals can be formed by chemolithoautotrophic bacteria, which gain a small amount of energy from iron oxidation. Similarly, manganese-rich minerals are formed during manganese oxidation, although how this reaction benefits microbes is unclear. These minerals and others give geologists and geomicrobiologists clues about early life on Earth. In addition to forming minerals, microbes help to dissolve them, a process called weathering. Microbes contribute to weathering and mineral dissolution through several mechanisms: production of protons (acidity) or hydroxides that dissolve minerals; production of ligands that chelate metals in minerals thereby breaking up the solid phase; and direct reduction of mineral-bound metals to more soluble forms. The chapter ends with some comments about the role of microbes in degrading oil and other fossil fuels.

Statistical micromechanical damage model for SH-SFRC under tensile load considering the interfacial slip-softening and matrix spalling effects

2021 ◽  
pp. 105678952110112
Author(s):  
Hehua Zhu ◽  
Xiangyang Wei ◽  
J Woody Ju ◽  
Qing Chen ◽  
Zhiguo Yan ◽  
...  
Keyword(s):  
Strain Hardening ◽  
Steel Fiber ◽  
Damage Model ◽  
Fiber Reinforced Concrete ◽  
Uniaxial Tensile ◽  
Interfacial Slip ◽  
Fiber Reinforced ◽  
Micromechanical Damage ◽  
The Impact ◽  
Micromechanical Damage Model

Strain hardening behavior can be observed in steel fiber reinforced concretes under tensile loads. In this paper, a statistical micromechanical damage framework is presented for the strain hardening steel fiber reinforced concrete (SH-SFRC) considering the interfacial slip-softening and matrix spalling effects. With a linear slip-softening interface law, an analytical model is developed for the single steel fiber pullout behavior. The crack bridging effects are reached by averaging the contribution of the fibers with different inclined angles. Afterwards, the traditional snubbing factor is modified by considering the fiber snubbing and the matrix spalling effects. By adopting the Weibull distribution, a statistical micromechanical damage model is established with the fracture mechanics based cracking criteria and the stress transfer distance. The comparison with the experimental results demonstrates that the proposed framework is capable of reproducing the SH-SFRC’s uniaxial tensile behavior well. Moreover, the impact of the interfacial slip-softening and matrix spalling effects are further discussed with the presented framework.

A solid-phase extraction method that eliminates matrix effects of complex pulp mill effluents for the analysis of lipophilic wood extractives

2020 ◽  
Vol 35 (4) ◽  
pp. 577-588
Author(s):  
Sebastian España Orozco ◽  
Philipp Zeitlinger ◽  
Karin Fackler ◽  
Robert H. Bischof ◽  
Antje Potthast
Keyword(s):  
Solid Phase Extraction ◽  
Matrix Effects ◽  
Solid Phase ◽  
Internal Standard ◽  
Pulp Mill ◽  
Phase Extraction ◽  
Wood Extractives ◽  
Wood Extractive ◽  
Pulp Mill Effluents ◽  
The Impact

AbstractThe extraction of lipophilic wood extractives from pulp and paper process waters proves to be a challenging task, due to harsh and alternating process and sample conditions. This study has determined the potential use of polymeric sorbents for solid-phase extraction (SPE) and compared to classical silica-based reversed-phase packed columns, with polymeric hydrophilic-lipophilic balanced (HLB) cartridges being the sorbent with the most potential. Recovery functions were obtained with an internal standard mixture representative for the main lipophilic wood extractive groups, which are fatty acids and alcohols, sterols, sterol esters and triglycerides. The impact of pH, sample volume and sample matrix, expressed as TOC and cations, on the retention behavior of lipophilic extractives during SPE of industrial samples were determined with polymeric HLB sorbent. High variations in the composition of pulp mill matrices led to different optimal extraction conditions. Thus, a new SPE protocol was developed, which bypasses matrix interferences and omits the loss of analytes due to sample preparation. The method is applicable to different pulp mill effluents with large discrepancies in pH and sample matrices, resulting in recoveries >90 % with RSD <5 % for all lipophilic wood extractives.

scholarly journals Solid-Phase Extraction Embedded Dialysis (SPEED), an Innovative Procedure for the Investigation of Microbial Specialized Metabolites

Marine Drugs ◽  
2021 ◽  
Vol 19 (7) ◽  
pp. 371
Author(s):  
Phuong-Y Mai ◽  
Géraldine Le Goff ◽  
Erwan Poupon ◽  
Philippe Lopes ◽  
Xavier Moppert ◽  
...  
Keyword(s):  
Solid Phase Extraction ◽  
Solid Phase ◽  
Chemical Space ◽  
Molecular Profile ◽  
Phase Extraction ◽  
Specialized Metabolites ◽  
Streptomyces Albidoflavus ◽  
Cultivation Process ◽  
The Impact

Solid-phase extraction embedded dialysis (SPEED technology) is an innovative procedure developed to physically separate in-situ, during the cultivation, the mycelium of filament forming microorganisms, such as actinomycetes and fungi, and the XAD-16 resin used to trap the secreted specialized metabolites. SPEED consists of an external nylon cloth and an internal dialysis tube containing the XAD resin. The dialysis barrier selects the molecular weight of the trapped compounds, and prevents the aggregation of biomass or macromolecules on the XAD beads. The external nylon promotes the formation of a microbial biofilm, making SPEED a biofilm supported cultivation process. SPEED technology was applied to the marine Streptomyces albidoflavus 19-S21, isolated from a core of a submerged Kopara sampled at 20 m from the border of a saltwater pond. The chemical space of this strain was investigated effectively using a dereplication strategy based on molecular networking and in-depth chemical analysis. The results highlight the impact of culture support on the molecular profile of Streptomyces albidoflavus 19-S21 secondary metabolites.

scholarly journals A Study of the Impact of Graphite on the Kinetics of SPS in Nano- and Submicron WC-10%Co Powder Compositions

Ceramics ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 331-363
Author(s):  
Eugeniy Lantcev ◽  
Aleksey Nokhrin ◽  
Nataliya Malekhonova ◽  
Maksim Boldin ◽  
Vladimir Chuvil'deev ◽  
...  
Keyword(s):  
Activation Energy ◽  
Solid Phase ◽  
Continuous Heating ◽  
Diffusion Creep ◽  
Hard Alloys ◽  
Fine Grained ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
The Impact ◽  
Kinetics Of

This study investigates the impact of carbon on the kinetics of the spark plasma sintering (SPS) of nano- and submicron powders WC-10wt.%Co. Carbon, in the form of graphite, was introduced into powders by mixing. The activation energy of solid-phase sintering was determined for the conditions of isothermal and continuous heating. It has been demonstrated that increasing the carbon content leads to a decrease in the fraction of η-phase particles and a shift of the shrinkage curve towards lower heating temperatures. It has been established that increasing the graphite content in nano- and submicron powders has no significant effect on the SPS activation energy for “mid-range” heating temperatures, QS(I). The value of QS(I) is close to the activation energy of grain-boundary diffusion in cobalt. It has been demonstrated that increasing the content of graphite leads to a significant decrease in the SPS activation energy, QS(II), for “higher-range” heating temperatures due to lower concentration of tungsten atoms in cobalt-based γ-phase. It has been established that the sintering kinetics of fine-grained WC-Co hard alloys is limited by the intensity of diffusion creep of cobalt (Coble creep).

Experimental manipulations of the biomass of introduced carp (Cyprinus carpio) in billabongs. II. Impacts on benthic properties and processes1

1997 ◽  
Vol 48 (5) ◽  
pp. 445 ◽  
Author(s):  
A. I. Robertson ◽  
M. R. Healey ◽  
A. J. King
Keyword(s):  
Algal Biomass ◽  
Solid Phase ◽  
Negative Impact ◽  
Oxygen Demand ◽  
Sediment Oxygen Demand ◽  
Sediment Surface ◽  
Nutrient Concentrations ◽  
Nutrient Ratios ◽  
Biofilm Development ◽  
The Impact

Two billabongs on the floodplain of the Murrumbidgee River, Australia, were partitioned in half with impermeable plastic barriers and the biomass of carp was manipulated to establish high- and low-carp biomass treatments in each billabong. Measurements of benthic variables (rates of particle settlement, biofilm development, sediment respiration, macrophyte detritus decomposition, sediment solid-phase nutrient concentrations and benthic algal biomass) were performed over four months from summer to winter 1995. Rates of particle settlement were greater in the high-carp treatment of each billabong throughout the experiment. High carp biomass had a negative impact on the autotrophic component of the biofilm developing on wood blocks placed at different heights above the sediment surface but the mechanism responsible differed between billabongs. Sediment oxygen demand became greater in the presence of a higher biomass of carp during the experiment but time courses differed between billabongs. Manipulations of carp biomass did not influence algal biomass on the sediment surface, the rate of decomposition of macrophyte detritus or sediment solid-phase nutrients or nutrient ratios. The impact of carp on benthic and surficial processes was significant but the mechanisms of change differed between billabongs.

Concrete and Fiber Reinforced Concrete Subjected to Impact Loading

1985 ◽  
Vol 64 ◽  
Author(s):  
Surendra P. Shah
Keyword(s):  
Fracture Toughness ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Basic Material ◽  
Strain History ◽  
Moderate Increase ◽  
Fiber Reinforced ◽  
The Impact

ABSTRACTDespite its extensive use, low tensile strength has been recognized as one of the major drawbacks of concrete. Although one has learned to avoid exposing concrete structures to adverse static tensile load, these cannot be shielded from short duration dynamic tensile stresses. Such loads originate from sources such as impact from missiles and projectiles, wind gusts, earthquakes and machine vibrations. The need to accurately predict the structural response and reserve capacity under such loading has led to an interest in the mechanical properties of the component materials at high rates of straining.One method to improve the resistance of concrete when subjected to impact and/or impulsive loading is by the incorporation of randomly distributed short fibers. Concrete (or Mortar) so reinforced is termed fiber reinforced concrete (FRC). Moderate increase in tensile strength and significant increases in energy absorption (toughness or impact-resistance) have been reported by several investigators in static tests on concrete reinforced with randomly distributed short steel fibers. A theoretical model to predict fracture toughness of FRC is proposed. This model is based on the concept of nonlinear elastic fracture mechanics.As yet no standard test methods are available to quantify the impact resistance of such composites, although several investigators have employed a variety of tests including drop weight, swinging pendulums and the detonation of explosives. These tests though useful in ascertaining the relative merits of different composites do not yield basic material characteristics which can be used for design.The author has recently developed an instrumented Charpy type of impact test to obtain basic information such as load-deflection relationship, fracture toughness, crack velocity and load-strain history during an impact event. From this information, a damage based constitutive model was proposed. Relative improvements in performance due to the addition of fibers as observed in the instrumented tests are also compared with other conventional methods.

Test and Study on Impact of Corrosion on Bond Force between Steel and Concrete

2010 ◽  
Vol 36 ◽  
pp. 176-181
Author(s):  
Xian Feng He ◽  
Shou Gang Zhao ◽  
Yuan Bao Leng
Keyword(s):  
Reinforced Concrete ◽  
Corrosion Rate ◽  
Concrete Structure ◽  
Steel Corrosion ◽  
Reinforced Concrete Structure ◽  
Bond Force ◽  
Steel Bars ◽  
Protection Layer ◽  
Corrosion Of Steel ◽  
The Impact

The corrosion of steel will have a bad impact on the safety of reinforced concrete structure. In severe cases, it may even be disastrous. In order to understand the impact of steel corrosion on the structure, tests are carried out to study corrosion and expansion rules of steel bars as well as the impact rules of corrosion on bond force between steel and concrete. The results show that wet and salty environment will result in steel corrosion; relatively minor corrosion will not cause expansion cracks of protection layers; when steel rust to a certain extent, it will cause cracks along the protection layer; when there exists minor corrosion in steel and the protection layer does not have expansion cracks, the bond force is still large and rapidly decreases as the corrosion rate increases.

Sign in / Sign up

Export Citation Format

Share Document